Alkali–silica reaction

The alkali–silica reaction (ASR), more commonly known as "concrete cancer", is a swelling reaction that occurs over time in concrete between the highly alkaline cement paste and the reactive non-crystalline (amorphous) silica found in many common aggregates, given sufficient moisture.

Characteristic crack pattern associated with the alkali–silica reaction affecting a concrete step barrier on a US motorway. Note the typical fatty aspect of the silicagel exudations imbibing the concrete surface along the two sides of the cracks.[1][2]

This reaction causes the expansion of the altered aggregate by the formation of a soluble and viscous gel of sodium silicate (Na2SiO3 • nH2O, also noted Na2H2SiO4 • nH2O, or N-S-H (sodium silicate hydrate), depending the adopted convention). This hygroscopic gel swells and increases in volume when absorbing water: it exerts an expansive pressure inside the siliceous aggregate, causing spalling and loss of strength of the concrete, finally leading to its failure.

ASR can lead to serious cracking in concrete, resulting in critical structural problems that can even force the demolition of a particular structure.[3][4] The expansion of concrete through reaction between cement and aggregates was first studied by Thomas E. Stanton in California during the 1930s with his founding publication in 1940.[5]

Chemistry
Typical crack pattern of the alkali-silica reaction (ASR). The gel exudations through the concrete cracks have a characteristic yellow color and a high pH. The fatty aspect of the exudations imbibing the concrete porosity along the cracks is also a distinctive feature of ASR.

To attempt to simplify and to stylize a very complex set of various reactions, the whole ASR reaction, after its complete evolution (ageing process) in the presence of sufficient Ca2+ cations available in solution, could be compared to the pozzolanic reaction which would be catalysed by the undesirable presence of excessive concentrations of alkali hydroxides (NaOH and KOH) in the concrete. It is a mineral acid-base reaction between NaOH or KOH, calcium hydroxide, also known as portlandite, or (Ca(OH)2), and silicic acid (H4SiO4, or Si(OH)4). For simplifying, after a complete exchange of the alkali cations with the calcium ions released by portlandite, the alkali-silica reaction in its ultimate stage leading to calcium silicate hydrate (C-S-H) could be schematically represented as following:

Ca(OH)2 + H4SiO4 → Ca2+ + H2SiO42− + 2 H2O → CaH2SiO4 • 2H2O

Here, the silicic acid H4SiO4, or Si(OH)4, which is equivalent to SiO2 · 2 H2O represents hydrous or amorphous silica for the sake of simplicity in aqueous chemistry.

Indeed, the term silicic acid has traditionally been used as a synonym for silica, SiO2. Strictly speaking, silica is the anhydride of orthosilicic acid, Si(OH)4.

SiO2↓ + 2 H2O ⇌ Si(OH)4

An ancient industrial notation referring to H
2SiO
3, metasilicic acid, is also often used to depict the alkali-silica reaction. However, the metasilicic acid, H
2SiO
3, or SiO(OH)
2, is a hypothetic molecule which has never been observed, even in extreme diluted solutions because H
2SiO
3 is unstable and continue to hydrate.

Indeed, contrary to the hydration of CO2 which consumes only one water molecule and stops at H2CO3, the hydration of SiO2 consumes two water molecules and continues one step further to form H4SiO4. The difference in hydration behaviour between SiO2 and CO2 is explained by thermodynamic reasons (Gibbs free energy) and by bond energy or steric hindrance around the central atom of the molecule.

That is why the more correct geochemical notation referring to the orthosilicic acid Si(OH)
4 really existing in dilute solution is preferred here. However, the main advantage of the now deprecated, but still often used, industrial notation referring to the metasilicate anion (SiO2–
3), which also does not exist in aqueous solution, is its greater simplicity and its direct similitude in notation with the carbonate (CO2–
3) system.

One will also note that the NaOH and KOH species (alkali hydroxides, also often simply called alkali to refer to their strongly basic character) which catalyze and accelerate the silica dissolution in the alkali-silica reaction do not explicitly appear in this simplified representation of the ultimate reaction with portlandite, because they are continuously regenerated from the cation exchange reaction with portlandite. As a consequence, they disappear from the global mass balance equation of the catalyzed reaction.

Silica dissolution mechanism
Anhydrous and hydrated silica surface with siloxane and silanol groups along with surface bound water molecules.

The surface of solid silica in contact with water is covered by siloxane bonds (≡Si–O–Si≡) and silanol groups (≡Si–OH) sensitive to an alkaline attack by OH−
 ions.

The presence of these oxygen-bearing groups very prone to form hydrogen bonds with water molecules explains the affinity of silica for water and makes colloidal silica very hydrophile.

Siloxane bonds may undergo hydrolysis and condensation reactions as schematically represented hereafter:

Siloxane bond between two silicon atoms.
≡Si–O–Si≡ + H
2O   ↔   ≡Si–OH + HO–Si≡
=Si=O + H
2O   ↔   =Si(–OH)
2
Chemical structure of a silanol group.

On the other hand, silanol groups can also undergo protonation/deprotonation:

≡Si–OH   ↔   ≡Si–O−
 + H+
.

These equilibria can be shifted towards the right side of the reaction leading to silica dissolution by increasing the concentration of hydroxide anion (OH–), i.e., by increasing the pH of the solution.

Alkaline hydrolysis of siloxane bonds occurs by nucleophilic substitution of OH– onto a silicon atom, while another –O–Si group is leaving to preserve the tetravalent character of Si atom:

≡Si–O–Si≡ + OH−
   →   ≡Si–OH + –O–Si≡
=Si=O + OH−
   →   =SiO(OH)−

Deprotonation of silanol groups:

≡Si–OH + OH−
   →   ≡Si–O−
 + H
2O.

In the pH range 0 – 7, the solubility of silica is constant, but above pH 8, the hydrolysis of siloxane bonds and deprotonation of silanol groups exponentially increase with pH. This is why glass easily dissolves at high pH and does not withstand extremely basic NaOH/KOH solutions. Therefore, NaOH/KOH released during cement hydration attacks and dissolves the tridimensional network of silica present in the aggregates. Amorphous or poorly crystallized silica, as cryptocrystalline chalcedony or chert present in flints (in chalk) or rolled river gravels, is much more soluble and sensitive to alkaline attack by OH– anions than well crystallized silica such as quartz. Strained (deformed) quartz or chert exposed to freeze-thaw cycles in Canada and Nordic countries are also more sensitive to alkaline (high pH) solutions.

The species responsible for silica dissolution is the hydroxide anion (OH–). The high pH conditions are said to be alkaline and one also speaks of the alkalinity of the basic solutions. For the sake of electroneutrality, (OH–) anions need to be accompanied by positively charged cations, Na+ or K+ in NaOH or KOH solutions respectively. Na and K both belong to the alkali metals column in the Mendeleev table. When speaking of alkali's, one systematically refers to NaOH and KOH basic hydroxides, or their corresponding oxides Na2O and K2O in cement. Therefore, it is the hydroxide, or the oxide, component of the salt which is the only relevant chemical species for silica dissolution, not the alkali metal in itself. However, to determine the alkali equivalent content (Na2Oeq) in cement, because the need to maintain electroneutrality in solids or in solution, one directly measures the contents of cement in Na and K elements and one conservatively considers that their counter ions are the hydroxide ions. As Na+ and K+ cations are hydrated species, they also contribute to retain water in alkali-silica reaction products.

Osmotic processes (Chatterji et al., 1986, 1987, 1989) and the electrical double layer (EDL)[6] play also a fundamental role in the transport of water towards the concentrated liquid alkali gel explaining their swelling behavior and the deleterious expansion of aggregates responsible of ASR damages in concrete.

Catalysis of ASR by dissolved NaOH or KOH

The ASR reaction significantly differs from the pozzolanic reaction by the fact that it is catalysed by soluble alkali hydroxides (NaOH / KOH) at very high pH. It can be represented as follows using the classical geochemical notation for representing silica by the fully hydrated dissolved silica (Si(OH)4 or silicic acid: H4SiO4), but an older industrial notation also exists (H2SiO3, hemihydrated silica (does not exist), by analogy with carbonic acid):

2 Na(OH) + H4SiO4 → Na2H2SiO4 • 2H2O
the so-produced soluble alkali silicagel can then react with calcium hydroxide (portlandite) to precipitate insoluble calcium silicate hydrates (C-S-H phases) and regenerate NaOH for continuing the initial silica dissolution reaction:
Na2H2SiO4 • 2H2O + Ca(OH)2 → CaH2SiO4 • 2H2O + 2 NaOH

The sum, or the combination, of the two above mentioned reactions gives a general reaction resembling the pozzolanic reaction, but it is important to keep in mind that this reaction is catalysed by the undesirable presence in cement, or other concrete components, of soluble alkaline hydroxydes (NaOH / KOH) responsible for the dissolution of the silica (silicic acid) at high pH:

Ca(OH)2 + H4SiO4 → CaH2SiO4 • 2H2O

Without the presence of dissolved NaOH or KOH, responsible for the high pH (~13.5) of the concrete pore water, the amorphous silica of the reactive aggregates would not be dissolved and the reaction would not evolve. Moreover, the soluble sodium or potassium silicate is very hygroscopic and swells when it absorbs water. When the sodium silicate gel forms and swells inside a porous siliceous aggregate, it first expands and occupies the free porosity. When this latter is completely filled, if the soluble but very viscous gel cannot be easily expelled from the silica network, the hydraulic pressure rises inside the attacked aggregate and leads to its fracture. It is the hydro-mechanical expansion of the damaged siliceous aggregate surrounded by calcium-rich hardened cement paste which is responsible for the development of a network of cracks in concrete. When the sodium silicate expelled from the aggregate encounters grains of portlandite present in the hardened cement paste, an exchange between sodium and calcium cations occurs and hydrated calcium silicate (C-S-H) precipitates with a concomitant release of NaOH. In its turn, the regenerated NaOH can react with the amorphous silica aggregate leading to an increased production of soluble sodium silicate. When a continuous rim of C-S-H completely envelops the external surface of the attacked siliceous aggregate, it behaves as a semi-permeable barrier and hinders the expulsion of the viscous sodium silicate while allowing the NaOH / KOH to diffuse from the hardened cement paste inside the aggregate. This selective barrier of C-S-H contributes to increase the hydraulic pressure inside the aggregate and aggravates the cracking process. It is the expansion of the aggregates which damages concrete in the alkali-silica reaction.

Portlandite (Ca(OH)2) represents the main reserve of OH– anions in the solid phase as emphasized by Wang and Gillott (1991).[7] As long as portlandite, or the siliceous aggregates, has not become completely exhausted, the ASR reaction will continue. The alkali hydroxides are continuously regenerated by the reaction of the sodium silicate with portlandite and thus represent the transmission belt of the ASR reaction driving it to completeness. It is thus impossible to interrupt the ASR reaction. The only way to avoid ASR in the presence of siliceous aggregates and water is to maintain the concentration of soluble alkali (NaOH and KOH) at the lowest possible level in concrete, so that the catalysis mechanism becomes negligible.

Analogy with the soda lime and concrete carbonation

The alkali-silica reaction mechanism catalysed by a soluble strong base as NaOH or KOH in the presence of Ca(OH)2 (alkalinity buffer present in the solid phase) can be compared with the carbonation process of soda lime. The silicic acid (H2SiO3 or SiO2) is simply replaced in the reaction by the carbonic acid (H2CO3 or CO2).

(1) CO2 + 2 NaOH  →   Na2CO3 + H2O (CO2 trapping by soluble NaOH)
(2) Na2CO3 + Ca(OH)2 → CaCO3 + 2 NaOH   (regeneration of NaOH after reaction with lime)
sum (1+2) CO2 + Ca(OH)2 → CaCO3 + H2O   (global reaction)

In the presence of water or simply ambient moisture, the strong bases, NaOH or KOH, readily dissolve in their hydration water (hygroscopic substances, deliquescence phenomenon) and this greatly facilitates the catalysis process because the reaction in aqueous solution occurs much faster than in the dry solid phase.[8] The moist NaOH impregnates the surface and the porosity of calcium hydroxide grains with a high specific surface area.[9] Soda lime is commonly used in closed-circuit diving rebreathers and in anesthesia systems.[10][11]

The same catalytic effect by the alkali hydroxides (function of the Na2Oeq content of cement) also contributes to the carbonation of portlandite by atmospheric CO2 in concrete although the rate of propagation of the reaction front is there essentially limited by the CO2 diffusion within the concrete matrix less porous.[12]

The soda lime carbonation reaction can be directly translated into the ancient industrial notation of silicate (referring to the never observed metasilicic acid) simply by substituting a C atom by a Si atom in the mass balance equations (i.e., by replacing a carbonate by a metasilicate anion). This gives the following set of reactions also commonly encountered in the literature to schematically depict the continuous regeneration of NaOH in ASR:

(1) SiO2 + 2 NaOH  →   Na2SiO3 + H2O (SiO2 quickly dissolved by hygroscopic NaOH)
(2) Na2SiO3 + Ca(OH)2 → CaSiO3 + 2 NaOH   (regeneration of NaOH after reaction with portlandite)
sum (1+2) SiO2 + Ca(OH)2 → CaSiO3 + H2O   (global reaction resembling the Pozzolanic reaction)

If NaOH is clearly deficient in the system under consideration (soda lime or alkali-silica reaction), it is formally possible to write the same reactions sets by simply replacing the CO32- anions by HCO3− and the SiO32- anions by HSiO3−, the principle of catalysis remaining the same, even if the number of intermediate species differs.

Main sources of OH−
 in hardened cement paste

One can distinguish several sources of hydroxide anions (OH−
) in hardened cement paste (HCP) from the family of Portland cement (pure OPC, with BFS, or with cementitious additions, FA or SF).

Direct sources

OH−
 anions can be directly present in the HCP pore water or be slowly released from the solid phase (main buffer, or solid stock) by the dissolution of Ca(OH)
2 (portlandite) when its solubility increases when high pH value starts to drop. Beside these two main sources, ions exchange reactions and precipitation of poorly soluble calcium salts can also contribute to release OH−
 into solution.

Alkali hydroxides, NaOH and KOH, arise from the direct dissolution of Na
2O and K
2O oxides produced by the pyrolysis of the raw materials at high temperature (1450 °C) in the cement kiln. The presence of minerals with high Na and K contents in the raw materials can thus be problematic. The ancient wet manufacturing process of cement, consuming more energy (water evaporation) that the modern dry process, had the advantage to eliminate much of the soluble Na and K salts present in the raw material.

As previously described in the two sections dealing respectively with ASR catalysis by alkali hydroxides and soda lime carbonation, soluble NaOH and KOH are continuously regenerated and released into solution when the soluble alkali silicate reacts with Ca(OH)
2 to precipitate insoluble calcium silicate. Therefore, portlandite is the main buffer of OH−
 in the solid phase. As long as the stock of hydroxide in the solid phase is not exhausted, the alkali-silica reaction can continue to proceed until complete disparition of one of the reagents (Ca(OH)
2 or SiO
2) involved in the pozzolanic reaction.

Indirect sources

There exist also other indirect sources of OH−
, all related to the presence of soluble Na and K salts in the pore water of hardened cement paste (HCP). The first category contains soluble Na and K salts whose corresponding anions can precipitate an insoluble calcium salts, e.g., Na
2SO
4, Na
2CO
3, Na
3PO
4, NaB(OH)
4, Na
2B
4O
7, ... .

Hereafter, an example for calcium sulfate (gypsum, anhydrite) precipitation releasing sodium hydroxide:

Na
2SO
4 + Ca(OH)
2 → CaSO
4 + 2 NaOH

or, the reaction of sodium carbonate with portlandite, also important for the catalysis of the alkali–carbonate reaction as emphasized by Fournier and Bérubé (2000) and Bérubé et al. (2005):[13][14]

Na
2CO
3 + Ca(OH)
2 → CaCO
3 + 2 NaOH

However, not all Na or K soluble salts can precipitate insoluble calcium salts, such as, e.g., NaCl-based deicing salts:

2 NaCl + Ca(OH)
2 ← CaCl
2 + 2 NaOH

As calcium chloride is a soluble salt, the reaction cannot occur and the chemical equilibrium regresses to the left side of the reaction.

So, a question arises: can NaCl or KCl from deicing salts still possibly play a role in the alkali-silica reaction? Na+
 and K+
 cations in themselves cannot attack silica (the culprit is their counter ion OH−
) and soluble alkali chlorides cannot produce soluble alkali hydroxide by interacting with calcium hydroxide. So, does it exist another route to still produce hydroxide anions in the hardened cement paste (HCP)?

Beside portlandite, other hydrated solid phases are present in HCP. The main phases are the calcium silicate hydrates (C-S-H) (the "glue" in cement paste), calcium sulfo-aluminate phases (AFm and AFt, ettringite) and hydrogarnet. C-S-H phases are less soluble (~ 10−5 M) than portlandite (CH) (~ 2.2 10−2 M at 25 °C) and therefore are expected to play a negligible role for the calcium ions release.

An anion-exchange reaction between chloride ions and the hydroxide anions contained in the lattice of some calcium aluminate hydrates (C-A-H), or related phases (C-A-S-H, AFm, AFt), is suspected to also contribute to the release of hydroxide anions into solution. The principle mechanism is schematically illustrated hereafter for C-A-H phases:

Cl−
 + (C-A-H)–OH → (C-A-H)–Cl + OH−

As a simple, but robust, conclusion, the presence of soluble Na and K salts can also cause, by precipitation of poorly soluble calcium salt (with portlandite, CH) or anion exchange reactions (with phases related to C-A-H), the release of OH−
 anions into solution. Therefore, the presence of any salts of Na and K in cement pore water is undesirable and the measurements of Na and K elements is a good proxy (indicator) for the maximal concentration of OH−
 in pore solution. This is why the total alkali equivalent content (Na
2O
eq) of cement can simply rely on the measurements of Na and K (e.g., by ICP-AES, AAS, XRF measurements techniques).

Alkali gel evolution and ageing

The maturation process of the fluid alkali silicagel found in exudations into less soluble solid products found in gel pastes or in efflorescences is described hereafter. Four distinct steps are considered in this progressive transformation.[7]

1. SiO
2 dissolution and Na
2SiO
3 formation (here, explicitly written in the ancient industrial metasilicate notation (based on the non-existing metasilicic acid, H
2SiO
3) to also illustrate the frequent use of this later in the literature):

2 NaOH + SiO
2 → Na
2SiO
3 · H
2O (young N-S-H gel)
this reaction is accompanied by hydration and swelling of the alkali gel leading to the expansion of the affected aggregates. The pH of the fresh alkali gel is very high and it has often a characteristic amber color. The high pH of young alkali gel exudations often precludes the growth of mosses at the surface of concrete crack infilling.

2. Maturation of the alkali gel: polymerisation and gelation by the sol–gel process. Condensation of silicate monomers or oligomers dispersed in a colloidal solution (sol) into a biphasic aqueous polymeric network of silicagel. Ca2+
 divalent cations released by calcium hydroxide (portlandite) when the pH starts to slightly drop may influence the gelation process.

3. Cation exchange with calcium hydroxide (portlandite) and precipitation of amorphous calcium silicate hydrates (C-S-H) accompanied by NaOH regeneration:

Na
2SiO
3 + Ca(OH)
2 → CaSiO
3 + 2 NaOH
Amorphous non-stoechiometric calcium silicate hydrates (C-S-H, the non-stoechiometry being denoted here by the use of dashes) can recrystallize into rosettes similar to these of gyrolite. The C-S-H formed at this stage can be considered an evolved calcium silicate hydrate.

4. Carbonation of the C-S-H leading to precipitation of calcium carbonate and amorphous SiO2 stylized as follows:

CaSiO
3 + CO
2 → CaCO
3 + SiO
2

As long as the alkali gel (Na
2SiO
3) has not yet reacted with Ca2+
 ions released from portlandite dissolution, it remains fluid and can easily exude from broken aggregates or through open cracks in the damage concrete structure. This can lead to visible yellow viscous liquid exudations (amber liquid droplets) at the surface of affected concrete.

When pH slowly drops due to the progress of the silica dissolution reaction, solubility of calcium hydroxide increases and the alkali gel reacts with Ca2+
 ions. Its viscosity increases due to gelation process and its mobility (fluidity) strongly decreases when C-S-H phases start to precipitate after reaction with calcium hydroxide (portlandite). At this moment, the calcified gel becomes hard, hindering therefore the alkali gel transport in concrete.

When the C-S-H gel is exposed to atmospheric carbon dioxide, it undergoes a rapid carbonation and white/yellow efflorescences appear at the surface of concrete. When the relatively fluid alkali gel continue to exude below the hardened superficial gel layer, it pushes the efflorescences out of the crack surface making them to appear in relief. Because the gel drying and carbonation reactions rates are faster than the gel exudation velocity (liquid gel expulsion rate through open cracks), in most of the cases, fresh liquid alkali exudates are not frequently encounterered at the surface of civil engineering concrete structures. Decompressed concrete cores can sometimes let observe fresh yellow liquid alkali exudations (viscous amber droplets) just after their drilling.

Mechanism of concrete deterioration

The mechanism of ASR causing the deterioration of concrete can thus be described in four steps as follows:

  1. The very basic solution (NaOH / KOH) attacks the siliceous aggregates (silicic acid dissolution at high pH), converting the poorly crystallised or amorphous silica to a soluble but very viscous alkali silicate gel (N-S-H, K-S-H).
  2. The consumption of NaOH / KOH by the dissolution reaction of amorphous silica decreases the pH of the pore water of the hardened cement paste. This allows the dissolution of Ca(OH)2 (portandite) and increases the concentration of Ca2+ ions into the cement pore water. Calcium ions then react with the soluble sodium silicate gel to convert it into solid calcium silicate hydrates (C-S-H). The C-S-H forms a continuous poorly permeable coating at the external surface of the aggregate.
  3. The penetrated alkaline solution (NaOH / KOH) converts the remaining siliceous minerals into bulky soluble alkali silicate gel. The resulting expansive pressure increases in the core of the aggregate.
  4. The accumulated pressure cracks the aggregate and the surrounding cement paste when the pressure exceeds the tolerance of the aggregate.[15]

Structural effects of ASR

The cracking caused by ASR can have several negative impacts on concrete, including:[16]

  1. Expansion: The swelling nature of ASR gel increases the chance of expansion in concrete elements.
  2. Compressive strength: The effect of ASR on compressive strength can be minor for low expansion levels, to relatively higher degrees at larger expansion. (Swamy R.N. 1986) points out that the compressive strength is not very accurate parameter to study the severity of ASR; however, the test is done because of its simplicity.
  3. Tensile strength / Flexural capacity: Researches show that ASR cracking can significantly reduce the tensile strength of concrete; therefore reducing the flexural capacity of beams. Some research on bridge structures indicate about 85% loss of capacity as a result of ASR.
  4. Modulus of elasticity/UPV: The effect of ASR on elastic properties of concrete and ultrasound pulse velocity (UPV) is very similar to tensile capacity. The modulus of elasticity is shown to be more sensitive to ASR than pulse velocity.
  5. Fatigue: ASR reduces the load bearing capacity and the fatigue life of concrete (Ahmed T. 2000).
  6. Shear strength: ASR enhances the shear capacity of reinforced concrete with and without shear reinforcement (Ahmed T. 2000).

Mitigation

ASR can be mitigated in new concrete by several complementary approaches:

  1. Limit the alkali metal content of the cement. Many standards impose limits on the "Equivalent Na2O" content of cement.
  2. Limit the reactive silica content of the aggregate. Certain volcanic rocks are particularly susceptible to ASR because they contain volcanic glass (obsidian) and should not be used as aggregate. The use of calcium carbonate aggregates is sometimes envisaged as an ultimate solution to avoid any problem. However, while it may be considered as a necessary condition, it is not a sufficient one. In principle, limestone (CaCO3) is not expected to contain a high level of silica, but it actually depends on its purity. Indeed, some siliceous limestones (a.o., Kieselkalk found in Switzerland)[17] may be cemented by amorphous or poorly crystalline silica and can be very sensitive to the ASR reaction, as also observed with some Tournaisian siliceous limestones exploited in quarries in the area of Tournai in Belgium.[18] In Canada, the Spratt siliceous limestone is also particularly well known in studies dealing with ASR and is commonly used as the Canadian ASR reference aggregate. So, the use of limestone as aggregate is not a guarantee against ASR in itself.
  3. Add very fine siliceous materials to neutralize the excessive alkalinity of cement with silicic acid by deliberately provoking a controlled pozzolanic reaction at the early stage of the cement setting. Convenient pozzolanic materials to add to the mix may be, e.g., pozzolan, silica fume, fly ash, or metakaolin.[19] These react preferentially with the cement alkalis without formation of an expansive pressure, because siliceous minerals in fine particles convert to alkali silicate and then to calcium silicate without formation of semipermeable reaction rims.
  4. Another method to reduce the ASR is to limit the external alkalis that come in contact with the system.

In other words, as it is sometimes possible to fight fire with fire, it is also feasible to combat the ASR reaction by itself. A prompt reaction initiated at the early stage of concrete hardening on very fine silica particles will help to suppress a slow and delayed reaction with larger siliceous aggregates on the long term. Following the same principle, the fabrication of low-pH cement also implies the addition of finely divided pozzolanic materials rich in silicic acid to the concrete mix to decrease its alkalinity. Beside initially lowering the pH value of the concrete pore water, the main working mechanism of silica fume addition is to consume portlandite (the reservoir of hydroxyde (OH–) in the solid phase) and to decrease the porosity of the hardened cement paste by the formation of calcium silicate hydrates (C-S-H). However, silica fume has to be very finely dispersed in the concrete mix, because agglomerated flakes of compacted silica fume can themselves also induce ASR if the dispersion process is insufficient. This can be the case in laboratory studies made on cement pastes alone in the absence of aggregates. However, most often, in large concrete batches, silica fume is sufficiently dispersed during mixing operations of fresh concrete by the presence of coarse and fine aggregates.

As part of a study conducted by the Federal Highway Administration, a variety of methods have been applied to field structures suffering from ASR-affected expansion and cracking. Some methods, such as the application of silanes, have shown significant promise, especially when applied to elements such as small columns and highway barriers, whereas other methods, such as the topical application of lithium compounds, have shown little or no promise in reducing ASR-induced expansion and cracking.[20]

Curative treatment

There are no curative treatments in general for ASR affected structures. Repair in damaged sections is possible, but the reaction will continue. In some cases, when a sufficient drying of thin components (walls, slabs) of a structure is possible, and is followed by the installation of a watertight membrane, the evolution of the reaction can be slow down, and sometimes stopped, because the lack of water to continue to fuel the reaction. Indeed, water plays a triple role in the alkali-silica reaction: solvent for the reaction taking place, transport medium for the dissolved species reacting, and finally also reagent consumed by the reaction itself.

However, concrete at the center of thick concrete components or structures can never dry because water transport in saturated or unsaturated conditions is always limited by diffusion in the concrete pores (water present under the liquid form, or under the vapor state). The water diffusion time is thus proportional to the square of its transport distance. As a consequence, the water saturation degree inside thick concrete structures often remains higher than 80%, a level sufficient to provide enough water to the system and to maintain the alkali-silica reaction on going.

Massive structures such as dams pose particular problems: they cannot be easily replaced, and the swelling can block spillway gates or turbine operations. Cutting slots across the structure can relieve some pressure, and help restore geometry and function.

Prevention of the risk

The only way to prevent, or to limit, the risk of ASR is to avoid one or several of the three elements in the critical triangle aggregate reactivity – cement alkali content – water:

  • by selecting non-reactive aggregates after testing them according to an appropriate standard test method (see next section);
  • by using a low-alkali (LA) cement: with a maximum alkali content expressed in Na
    2    O
    eq     < 0.60% of the cement mass, according to EN 197-1 European standard for cement,[21] or by limiting the total alkali content in concrete (e.g., less than 3 kg Na
    2    O
    eq    /m3 of concrete for a CEM I cement (OPC)). Example of standard for concrete in Belgium: NBN EN 206 and its national supplement NBN B 15-001;[22][23]
  • by limiting the contact of underground or meteoritic water infiltrations with the concrete structure (water tight membrane, roofing, sufficient water drainage, ...). This last precaution is always advisable when possible and the only one also sometimes applicable for existing ASR-affected concrete structures.

Methods for testing potential alkali reactivity

The American Society for Testing and Materials (ASTM International) has developed different standardized test methods for screening aggregates for their susceptibility to ASR:

  • ASTM C227: “Test Method for Potential Alkali Reactivity of Cement-Aggregate Combinations (Mortar-Bar Method)”
  • ASTM C289: "Standard Test Method for Potential Alkali-Silica Reactivity of Aggregates (Chemical Method)"
  • ASTM C295: “Guide for Petrographic Examination of Aggregate for Concrete”
  • ASTM C1260: “Test Method for Potential Reactivity of Aggregates (Mortar-Bar-Test)”. It is a rapid test of aggregates: immersion of mortar bars in NaOH 1 M at 80 °C for 14 days used to quickly identify highly reactive aggregates or quasi non-reactive aggregates. Beside an elevated temperature, the C1260 method also involves the use of a large quantity/inventory of NaOH in the solution in which the mortar bar is immersed. A large pool of OH– anions is thus available to diffuse inside the mortar bar to dissolve silica present in aggregates. Consequently, this test is very severe and may exclude valuable aggregates. In case of non-decisive results, the long-term ASTM C1293 test method has to be used for a final screening. The main advantage of the ASTM C1260 test is that it allows to quickly identify extreme cases: very insensitive or very reactive aggregates.
  • ASTM C1293: “Test Method for Concrete Aggregates by Determination of Length Change of Concrete Due to Alkali-Silica Reaction”. It is a long-term confirmation test (1 or 2 years) at 38 °C in a water-saturated moist atmosphere (inside a thermostated oven) with concrete prisms containing the aggregates to be characterised mixed with a high-alkali cement specially selected to induce ASR. The concrete prisms are not directly immersed in an alkaline solution, but wrapped with moist tissues and tightly packed inside a water-tight plastic foils.
  • ASTM C1567: "Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method)"

Other concrete prism methods have also been internationally developed to detect potential alkali-reactivity of aggregates or sometimes hardened concrete cores, e.g.:

  • The Oberholster method on which the ASTM C1260 test is based.
  • The Dungan method with superimposed additional thermal cycles.
  • The concrete microbar test was proposed by Grattan-Bellew et al. (2003) as a universal accelerated test for alkali-aggregate reaction.[24]
  • LCPC/IFSTTAR (1997) LPC-44. Alkali reaction in concrete. Residual expansion tests on hardened concrete.[25]
  • RILEM AAR-3 concrete prism method (storage at 38 °C).
  • RILEM AAR-4 concrete prism method (storage at 60 °C).
  • RILEM AAR-4 alternative method (storage at 60 °C).
  • German concrete test method (storage at 40 °C).
  • Norwegian concrete prism method (storage at 38 °C).

Known affected structures
Surface of a concrete pillar of the building of the National Gallery of Canada at Ottawa presenting the typical crack pattern of the alkali-silica reaction (ASR). Note the typical fatty aspect of the yellow silicagel exudations imbibing the concrete surface along the two sides of the cracks.

Australia

Belgium

Canada

Alkali-aggregate reactions (AAR), both alkali-silica (ASR) and alkali-carbonate (ACR, involving dolomite) reactions, were identified in Canada since the years 1950's.[38][39][40]

  • Many hydraulic dams are affected by ASR in Canada because of the wide use of reactive aggregates.[41] Indeed, reactive frost-sensitive chert is very often found in glacio-fluvial environments from which gravels are commonly extracted in Canada. Another reason is also the presence of reactive silica in Paleozoic limestones like the siliceous Ordovician limestone (Bobcaygeon Formation) from the Spratt's quarry near Ottawa in Ontario.[42] The Spratt's limestone aggregates (from the company "Spratt Sand and Gravel Limited") are widely used for ASR studies in Canada and worldwide as described by Rogers et al. (2000)[38] and also recommended by RILEM (International Union of Laboratories and Experts in Construction Materials, Systems, and Structures).[43]
  • Many bridges and civil engineering works of motorways.
  • Gentilly 2 nuclear power plant
  • Building of the National Gallery of Canada at Ottawa.

France

Germany
  • East German Deutsche Reichsbahn used numerous concrete ties in the 1970s to replace previous wooden ties. However, the gravel from the Baltic Sea caused ASR and the ties had to be replaced earlier than planned, lasting well into the 1990s.
  • After reunification, many Autobahns in East Germany were refurbished with concrete that turned out to have been defective and affected by ASR, necessitating expensive replacement work.

New Zealand

United Kingdom

United States

See also
  • "Alkali Silica Reaction – an overview – ScienceDirect Topics". www.sciencedirect.com. Retrieved 28 April 2020.
  • Understanding cement website treatise on ASR
  • PCA treatise on ASR
  • Concrete Construction Net treatise of ASR
  • US Federal Highway Administration (FHWA) treatise on the use of lithium to prevent or mitigate ASR
  • Association of German Cement Works – Alkali-silica reaction – Overview

Reference textbooks
  • Sims, Ian; Poole, Alan B. (2017-08-01). Alkali-aggregate reaction in concrete: A world review. CRC Press. ISBN 978-1-317-48441-7.

References
  1. FHWA (2010-06-22). "Alkali-Silica Reactivity (ASR) – Concrete – Pavements – FHWA". Alkali-Silica Reactivity (ASR) Development and Deployment Program. Archived from the original on 8 August 2010. Retrieved 2010-07-28.
  2. Faridazar, Fred (2009-02-10). "Techbrief: Selecting candidate structures for lithium treatment: What to provide the petrographer along with concrete specimens, FHWA-HRT-06-069 – Pavements – FHWA". FHWA-HRT-06-069. Retrieved 2010-07-28.
  3. "Alkali–silica reaction in concrete". Understanding Cement. Archived from the original on 10 August 2007. Retrieved 2007-08-11.
  4. "Merafield Bridge in Plympton demolished". BBC News. Retrieved 2016-05-16.
  5. Stanton, T.E. (1940). "Expansion of concrete through reaction between cement and aggregate". Engineering News-Record. No. SP-249-1.
  6. Prezzi, Monica; Monteiro, Paulo J.M.; Sposito, Garrison (1997). "The alkali–silica reaction: Part I. Use of the double-layer theory to explain the behavior of reaction-product gels". ACI Materials Journal. 94 (1): 10–17. ISSN 0889-325X.
  7. Wang, H.; Gillott, J. E. (1991-07-01). "Mechanism of alkali-silica reaction and the significance of calcium hydroxide". Cement and Concrete Research. 21 (4): 647–654. doi:10.1016/0008-8846(91)90115-X. ISSN 0008-8846.
  8. Samari, Mohammad; Ridha, Firas; Manovic, Vasilije; Macchi, Arturo; Anthony, E. J. (2019). "Direct capture of carbon dioxide from air via lime-based sorbents". Mitigation and Adaptation Strategies for Global Change. doi:10.1007/s11027-019-9845-0. ISSN 1381-2386.
  9. Ševčík, Radek; Mácová, Petra; Sotiriadis, Konstantinos; Pérez-Estébanez, Marta; Viani, Alberto; Šašek, Petr (2016). "Micro-Raman spectroscopy investigation of the carbonation reaction in a lime paste produced with a traditional technology". Journal of Raman Spectroscopy. 47 (12): 1452–1457. Bibcode:2016JRSp...47.1452S. doi:10.1002/jrs.4929. ISSN 0377-0486.
  10. Adriani, J.; Byrd, M. L. (1941). "A study of carbon dioxide absorption appliances for anesthesia: The canister". Anesthesiology: The Journal of the American Society of Anesthesiologists. 2 (4): 450–455.
  11. Freeman, Brian S.; Berger, Jeffrey S. (2014). Anesthesiology Core Review: Part One Basic Exam. Chapter 17: Absorption of Carbon Dioxide. McGraw-Hill Education. Retrieved 22 April 2020 – via Access Medicine.
  12. Verbeck, G. (1958). "Carbonation of hydrated Portland cement". STP205-EB Cement and Concrete (West Conshohocken, PA: ASTM International: 17–36. doi:10.1520/STP39460S. ISBN 978-0-8031-5667-8.
  13. Fournier, B., & Bérubé, M. A. (2000). Alkali-aggregate reaction in concrete: a review of basic concepts and engineering implications. Canadian Journal of Civil Engineering, 27(2), 167-191. See the chemical equations on p. 168.
  14. Bérubé, M. A., Smaoui, N., Bissonnette, B., & Fournier, B. (2005). Outil d’évaluation et de gestion des ouvrages d’art affectés de réactions alcalis-silice (RAS). Études et Recherches en Transport, Ministère des Transports du Québec. See the chemical equations on pp. 3-4.
  15. Ichikawa, T.; Miura, M. (2007). "Modified model of alkali-silica reaction". Cement and Concrete Research. 37 (9): 1291–1297. doi:10.1016/j.cemconres.2007.06.008.
  16. "Structural Effects of ASR on Concrete Structures | FPrimeC Solutions". FPrimeC Solutions. 2016-10-28. Retrieved 2017-01-11.
  17. Funk, Hanspeter (1975). "The origin of authigenic quartz in the Helvetic Siliceous Limestone (Helvetischer Kieselkalk), Switzerland". Sedimentology. 22 (2): 299–306. Bibcode:1975Sedim..22..299F. doi:10.1111/j.1365-3091.1975.tb00296.x.
  18. Monnin, Y.; Dégrugilliers P.; Bulteel D.; Garcia-Diaz E. (2006). "Petrography study of two siliceous limestones submitted to alkali-silica reaction". Cement and Concrete Research. 36 (8): 1460–1466. doi:10.1016/j.cemconres.2006.03.025. ISSN 0008-8846.
  19. Ramlochan, Terrence; Michael Thomas; Karen A. Gruber (2000). "The effect of metakaolin on alkali-silica reaction in concrete". Cement and Concrete Research. 30 (3): 339–344. doi:10.1016/S0008-8846(99)00261-6. ISSN 0008-8846.
  20. "Publication Details for Alkali-Aggregate Reactivity (AAR) Facts Book - Pavements - FHWA". dot.gov.
  21. EN 197-1 European Standard. Cement – Part 1: Composition, specifications and conformity criteria for common cements.
  22. NBN EN 206:2013+A1:2016 Concrete – Specification, performance, production and conformity. Publication date: 11/2016.
  23. NBN B 15-001:2018. Concrete – Specification, performance, production and conformity – National supplement for Belgium to NBN EN 206:2013+A1:2016. Publication date: 07/2018.
  24. Grattan-Bellew, P.E.; G. Cybanski; B. Fournier; L. Mitchell (2003). "Proposed universal accelerated test for alkali-aggregate reaction: the concrete microbar test". Cement Concrete and Aggregates. 25 (2): 29–34.
  25. LCPC/IFSTTAR (1997) Alcali-réaction du béton. Essai d’expansion résiduelle sur béton durci. Projet de méthode d’essai LCP 44. Février 1997. 15 pp. MethodeDEssai-LCPC-ME44.pdf. https://www.ifsttar.fr/fileadmin/user_upload/editions/lcpc/MethodeDEssai/MethodeDEssai-LCPC-ME44.pdf
  26. "Adelaide Festival Plaza redevelopment".
  27. "Manly Daily | News Local Newspaper | Daily Telegraph | Manly Daily | Daily Telegraph".
  28. Anna Vlach, The Adelaide Advertiser, “Pat bridge load fears”, 8 August 2007, page 9.
  29. Jane Whitford Guardian Messenger December 14, 2011
  30. "404". www.architecture.com.au.
  31. "ASR first recognised in Belgium civil engineering structures — Service Public Wallon: Direction de l'expertise des ouvrages" (PDF). 2010-09-15.
  32. http://www.ondraf.be/, web site of ONDRAF/NIRAS announcing in September 2013 the discovery on the interim storage site of Belgoprocess at Dessel of 10 000 LILW drums affected or potentially affected by ASR.
  33. "MONA website: Conditioned radioactive waste affected by ASR in Belgium — Gelvaten niet geschikt voor berging" (PDF). 2014-03-01.
  34. "STORA website: Conditioned radioactive waste affected by ASR in Belgium — Gelvaten problematiek".
  35. "STORA website: Conditioned radioactive waste affected by ASR in Belgium — Nieuw opslaggebouw voor gelvaten". 2014-09-26.
  36. "STORA website: Conditioned radioactive waste affected by ASR in Belgium — Nieuw opslaggebouw voor gelvaten klaar in 2019". 2016-09-29.
  37. "NIRAS magazine June 2016: Conditioned radioactive waste affected by ASR in Belgium — Nieuw hoogtechnologisch opslaggebouw voor vaten met gelvorming, pp. 20-21" (PDF). 2016-06-01.
  38. Rogers, C., Grattan-Bellew, P. E., Hooton, R. D., Ryell, J., & Thomas, M. D. (2000). Alkali-aggregate reactions in Ontario. Canadian Journal of Civil Engineering, 27(2), 246-260.
  39. Fournier, B., & Bérubé, M. A. (2000). Alkali-aggregate reaction in concrete: a review of basic concepts and engineering implications. Canadian Journal of Civil Engineering, 27(2), 167-191.
  40. Bérubé, M. A., Smaoui, N., Bissonnette, B., & Fournier, B. (2005). Outil d’évaluation et de gestion des ouvrages d’art affectés de réactions alcalis-silice (RAS). Études et Recherches en Transport, Ministère des Transports du Québec.
  41. Du, Chongjiang (2010). "HRW-Hydro Review Worldwide: Dealing with alkali-aggregate reaction in hydraulic structures".
  42. Limestone Industries of Ontario, Volume 2 Ontario Geological Survey. Engineering and Terrain Geology Section Ontario, Ministry of Natural Resources, 1989 – Limestone – 196 pages
  43. Nixon, J. P., & Sims, I. (Eds.). (2016). RILEM recommendation of the prevention of damage by alkali-aggregate reactions in new concrete structures. Dordrecht: Springer.
  44. "Fairfield Bridge". Hamilton City Libraries. Archived from the original on 2009-10-23. Retrieved 2009-10-23.
  45. "Keybridge House, London - Building #1458". www.skyscrapernews.com.
  46. Laura Kemp, Wales on Sunday, “THE Millennium Stadium is suffering from concrete cancer, we can reveal”, 8 July 2007;
  47. "A38 Merafield Bridge replacement". www.highways.gov.uk. 27 August 2014. Archived from the original on 21 May 2016. Retrieved 16 May 2016.
  48. "Merafield Bridge in Plympton demolished". BBC News. 16 May 2016. Retrieved 14 August 2017.
  49. "Pebble Mill Studios". BUFVC. BUFC. Retrieved 27 March 2018.
  50. Warner, Brian (26 March 1992). "UK: Eight contractors prepare bids for £22m Royal Devon and Exeter Hospital redevelopment contract". Construction News.
  51. "The Royal Devon and Exeter Hospital". Exeter Memories. 7 January 2014.
  52. Report DSO-2014-03: Seminoe dam – Assessment of concrete by quantitative methods – The petrographic damage rating index.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.