Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [check-snmp]

14 questions
2
votes
5 answers

Issue warnings with text output of check_snmp in Nagios

I'm trying to configure Icinga to query the SMART status of the hard drives loaded into a storage array I'm configuring. The issue I've run into is the response from the array when querying the OID of a drive is text, and not a number. ./check_snmp…
DKNUCKLES
  • 4,028
  • 9
  • 45
  • 60
2
votes
2 answers

check_snmp warning & critical thresholds with negative values

I'm querying some signal level values measured in dBm, and the SNMP host on the remove device reports the values as negative values, ie, -90 dBm. However, check-snmp seems to be incapable of dealing with negative numbers as part of its threshold…
Oesor
  • 300
  • 1
  • 2
  • 16
1
vote
1 answer

Unable to provide check_snmp_int.pl data to Graphite and JasperReports

I am an absolute beginner with Icinga and I have already tried several desperate attempts at finding a solution to it. After finally bringing check_snmp_int.pl to give me performance data I've tried to provide this data to JasperReports and…
GHUrekMazino
  • 11
  • 3
1
vote
1 answer

Nagios Core to monitor Cisco VPN Tunnel

I am able to see if a VPN tunnel is up using check_snmp. The OID for one of my tunnels is .1.3.6.1.4.1.9.9.171.1.2.3.1.35.3002962. When the tunnel is up, no problems. The problem, is when the tunnel is down, because the OID is gone.…
systems1984
  • 11
  • 3
1
vote
1 answer

Get information about inodes via snmp for linux

I want to check inodes via snmp for linux system, set up check. I could not find the correspondent MIB. Can any one help me to get information about inodes prozent ?
Abdou
  • 11
  • 1
  • 2
1
vote
3 answers

nagios check_snmp reverse - CRITICAL=0 OK=1

I need to check the status of power supply units Cisco 7604 using Nagios. I decided to use the plugin check_snmp: /usr/local/libexec/nagios/check_snmp -H 192.168.150.200 -o 1.3.6.1.4.1.9.9.91.1.1.1.1.4.13 SNMP OK - 1 |…
Allan Sundry
  • 53
  • 1
  • 2
  • 8
1
vote
2 answers

check_snmp with snmpv3 protocol giving "Unkown Report message" error

I'm trying to add a nagios command to use snmpv3 for monitoring printer status messages. When using the check_snmp command, I get the following error: External command error: snmpget: Unknown Report message Here is the command I'm typing…
John
  • 111
  • 1
  • 5
1
vote
1 answer

How to change Nagios check_snmp configuration to use SNMP v3

I posted this on SuperUser but I realized this question is probably more relevant here. I am trying to check uptime via Nagios's check_snmp plugin on a SNMP version 3 enabled UPS. I'm able to do an snmpget call specifying version 3 with the proper…
DuckReconMajor
  • 41
  • 1
  • 4
0
votes
2 answers

bidirectional Bandwidth measurement snmp with remote office

Hello I have a dedicated system for monitoring connected to the network in all remote offices. Our main/nagios server have connection to all. I want to get the bidirectional Bandwidth measurement between the dedicated system and nagios server.…
Sanctriell
  • 1
0
votes
0 answers

check_snmp plugin on nagios returns: External command error: snmpget: Authentication failure (incorrect password, community or key)

I’m trying to check the uptime of a Cisco 2960X switch on Nagios with check_snmp plugin but I always get the following error: [root@nagios]# /usr/lib64/nagios/plugins/check_snmp -P 3 -U snmpv3user -L authPriv -a MD5 -A v3p4ssword#1 -x DES -X…
Pedro Roeseler
  • 11
  • 2
0
votes
1 answer

Nagios check_snmp (New Response) CRITICAL 7

I have got a new critical figure / output as 7 SNMP CRITICAL - *7* What does above 7 refer to?
Zahid Hussain
  • 1
  • 1
  • 1
0
votes
1 answer

nagios check_snmp ifoperstatus not OK

I'm reading Monitoring Routers and Switches page, in particular "Monitoring SNMP Status Information" section. quote: In the example above, the "-o ifOperStatus.1" refers to the OID for the operational status of port 1 on the switch. The "-r 1"…
alexus
  • 12,342
  • 27
  • 115
  • 173
0
votes
1 answer

Automatically adding comments to snmpd.conf

I have a snmpd.conf which looks like this. I would like the comments to auto-fill i.e. make the file human readable with explanations. If it were one file, I could have done copy/paste from default one, but there are many different ones. Is there a…
Prashanth Sundaram
  • 451
  • 4
  • 10
0
votes
1 answer

check_snmp plugin timedout icinga2

I am new to icinga, and at the moment I am trying to monitor a paloalto firewall running paOS 9.0 with OID 1.3.6.1.2.1.25.3.3.1.2.1 (hrProcessorLoad.1), but I have problems with the check_snmp plugin that is costantly timing out and I don't know…
msana
  • 3
  • 1