Gemstone

A gemstone (also called a gem, fine gem, jewel, precious stone, or semi-precious stone) is a piece of mineral crystal which, in cut and polished form, is used to make jewelry or other adornments.[1][2][3] However, certain rocks (such as lapis lazuli and opal) and occasionally organic materials that are not minerals (such as amber, jet, and pearl) are also used for jewelry and are therefore often considered to be gemstones as well. Most gemstones are hard, but some soft minerals are used in jewelry because of their luster or other physical properties that have aesthetic value. Rarity is another characteristic that lends value to a gemstone.

Several terms redirect here. For other uses, see Gemstone (disambiguation), Gem (disambiguation), Gems (disambiguation), Jewels (disambiguation) and Precious Stone (disambiguation).
Group of precious and semiprecious stones—both uncut and faceted—including (clockwise from top left) diamond, uncut synthetic sapphire, ruby, uncut emerald, and amethyst crystal cluster.

Apart from jewelry, from earliest antiquity engraved gems and hardstone carvings, such as cups, were major luxury art forms. A gem maker is called a lapidary or gemcutter; a diamond cutter is called a diamantaire.

Characteristics and classification
A selection of gemstone pebbles made by tumbling rough rock with abrasive grit, in a rotating drum. The biggest pebble here is 40 mm (1.6 in) long.

The traditional classification in the West, which goes back to the ancient Greeks, begins with a distinction between precious and semi-precious; similar distinctions are made in other cultures. In modern use the precious stones are diamond, ruby, sapphire and emerald, with all other gemstones being semi-precious.[4] This distinction reflects the rarity of the respective stones in ancient times, as well as their quality: all are translucent with fine color in their purest forms, except for the colorless diamond, and very hard, with hardnesses of 8 to 10 on the Mohs scale. Other stones are classified by their color, translucency and hardness. The traditional distinction does not necessarily reflect modern values, for example, while garnets are relatively inexpensive, a green garnet called tsavorite can be far more valuable than a mid-quality emerald.[5] Another unscientific term for semi-precious gemstones used in art history and archaeology is hardstone. Use of the terms 'precious' and 'semi-precious' in a commercial context is, arguably, misleading in that it deceptively implies certain stones are intrinsically more valuable than others, which is not necessarily the case.

In modern times gemstones are identified by gemologists, who describe gems and their characteristics using technical terminology specific to the field of gemology. The first characteristic a gemologist uses to identify a gemstone is its chemical composition. For example, diamonds are made of carbon (C) and rubies of aluminium oxide (Al
2O
3). Many gems are crystals which are classified by their crystal system such as cubic or trigonal or monoclinic. Another term used is habit, the form the gem is usually found in. For example, diamonds, which have a cubic crystal system, are often found as octahedrons.

Gemstones are classified into different groups, species, and varieties.[6] For example, ruby is the red variety of the species corundum, while any other color of corundum is considered sapphire. Other examples are the emerald (green), aquamarine (blue), red beryl (red), goshenite (colorless), heliodor (yellow) and morganite (pink), which are all varieties of the mineral species beryl.

Gems are characterized in terms of refractive index, dispersion, specific gravity, hardness, cleavage, fracture and luster. They may exhibit pleochroism or double refraction. They may have luminescence and a distinctive absorption spectrum.

Material or flaws within a stone may be present as inclusions.

Gemstones may also be classified in terms of their "water". This is a recognized grading of the gem's luster, transparency, or "brilliance".[7] Very transparent gems are considered "first water", while "second" or "third water" gems are those of a lesser transparency.[8]

Value
Spanish emerald and gold pendant at Victoria and Albert Museum
Enamelled gold, amethyst and pearl pendant, about 1880, Pasquale Novissimo (1844–1914), V&A Museum number M.36-1928

Gemstones have no universally accepted grading system. Diamonds are graded using a system developed by the Gemological Institute of America (GIA) in the early 1950s. Historically, all gemstones were graded using the naked eye. The GIA system included a major innovation: the introduction of 10x magnification as the standard for grading clarity. Other gemstones are still graded using the naked eye (assuming 20/20 vision).[9]

A mnemonic device, the "four Cs" (color, cut, clarity, and carats), has been introduced to help the consumer understand the factors used to grade a diamond.[10] With modification, these categories can be useful in understanding the grading of all gemstones. The four criteria carry different weight depending upon whether they are applied to colored gemstones or to colorless diamonds. In diamonds, cut is the primary determinant of value, followed by clarity and color. The ideal cut diamond will sparkle, to break down light into its constituent rainbow colors (dispersion), chop it up into bright little pieces (scintillation), and deliver it to the eye (brilliance). In its rough crystalline form, a diamond will do none of these things; it requires proper fashioning and this is called "cut". In gemstones that have color, including colored diamonds, the purity and beauty of that color is the primary determinant of quality.

Physical characteristics that make a colored stone valuable are color, clarity to a lesser extent (emeralds will always have a number of inclusions), cut, unusual optical phenomena within the stone such as color zoning (the uneven distribution of coloring within a gem) and asteria (star effects). Ancient Greeks, for example, greatly valued asteria gemstones, which they regarded as powerful love charms, and Helen of Troy was known to have worn star-corundum.[11]

Aside from the diamond, the ruby, sapphire, emerald, pearl (not, strictly speaking, a gemstone), and opal[12] have also been considered to be precious. Up to the discoveries of bulk amethyst in Brazil in the 19th century, amethyst was considered a "precious stone" as well, going back to ancient Greece. Even in the last century certain stones such as aquamarine, peridot and cat's eye (cymophane) have been popular and hence been regarded as precious.

Today the gemstone trade no longer makes such a distinction.[13] Many gemstones are used in even the most expensive jewelry, depending on the brand-name of the designer, fashion trends, market supply, treatments, etc. Nevertheless, diamonds, rubies, sapphires, and emeralds still have a reputation that exceeds those of other gemstones.[14]

Rare or unusual gemstones, generally understood to include those gemstones which occur so infrequently in gem quality that they are scarcely known except to connoisseurs, include andalusite, axinite, cassiterite, clinohumite and red beryl.[15]

Gemstone pricing and value are governed by factors and characteristics in the quality of the stone. These characteristics include clarity, rarity, freedom from defects, beauty of the stone, as well as the demand for such stones. There are different pricing influencers for both colored gemstones, and for diamonds. The pricing on colored stones is determined by market supply-and-demand, but diamonds are more intricate. Diamond value can change based on location, time, and on the evaluations of diamond vendors.[16]

Proponents of energy medicine also value gemstones on the basis of alleged healing powers.[17]

Grading

There are a number of laboratories which grade and provide reports on gemstones.[13]

  • Gemological Institute of America (GIA), the main provider of education services and diamond grading reports
  • International Gemological Institute (IGI), independent laboratory for grading and evaluation of diamonds, jewelry and colored stones
  • Hoge Raad voor Diamant (HRD Antwerp), The Diamond High Council, Belgium is one of Europe's oldest laboratories; its main stakeholder is the Antwerp World Diamond Centre
  • American Gemological Society (AGS) is not as widely recognized nor as old as the GIA
  • American Gem Trade Laboratory which is part of the American Gem Trade Association (AGTA), a trade organization of jewelers and dealers of colored stones
  • American Gemological Laboratories (AGL), owned by Christopher P. Smith
  • European Gemological Laboratory (EGL), founded in 1974 by Guy Margel in Belgium
  • Gemmological Association of All Japan (GAAJ-ZENHOKYO), Zenhokyo, Japan, active in gemological research
  • The Gem and Jewelry Institute of Thailand (Public Organization) or GIT, the Thailand's national institute for gemological research and gem testing, Bangkok[18]
  • Gemmology Institute of Southern Africa, Africa's premium gem laboratory
  • Asian Institute of Gemological Sciences (AIGS), the oldest gemological institute in South East Asia, involved in gemological education and gem testing
  • Swiss Gemmological Institute (SSEF), founded by Henry Hänni, focusing on colored gemstones and the identification of natural pearls
  • Gübelin Gem Lab, the traditional Swiss lab founded by Eduard Gübelin
  • Institute for Gems and Gold Research of VINAGEMS (Vietnam), founded by Dr. Van Long Pham

Each laboratory has its own methodology to evaluate gemstones. A stone can be called "pink" by one lab while another lab calls it "padparadscha". One lab can conclude a stone is untreated, while another lab might conclude that it is heat-treated.[13] To minimise such differences, seven of the most respected labs, AGTA-GTL (New York), CISGEM (Milano), GAAJ-ZENHOKYO (Tokyo), GIA (Carlsbad), GIT (Bangkok), Gübelin (Lucerne) and SSEF (Basel), have established the Laboratory Manual Harmonisation Committee (LMHC), for the standardization of wording reports, promotion of certain analytical methods and interpretation of results. Country of origin has sometimes been difficult to determine, due to the constant discovery of new source locations. Determining a "country of origin" is thus much more difficult than determining other aspects of a gem (such as cut, clarity, etc.).[19]

Gem dealers are aware of the differences between gem laboratories and will make use of the discrepancies to obtain the best possible certificate.[13]

Cutting and polishing
Raw sapphire stones stored in a rural commercial cutting plant in Thailand.
A diamond cutter in Amsterdam in the Netherlands in 2012

A few gemstones are used as gems in the crystal or other form in which they are found. Most however, are cut and polished for usage as jewelry. The two main classifications are stones cut as smooth, dome shaped stones called cabochons, and stones which are cut with a faceting machine by polishing small flat windows called facets at regular intervals at exact angles.

Stones which are opaque or semi-opaque such as opal, turquoise, variscite, etc. are commonly cut as cabochons. These gems are designed to show the stone's color or surface properties as in opal and star sapphires. Grinding wheels and polishing agents are used to grind, shape and polish the smooth dome shape of the stones.[20]

Gems which are transparent are normally faceted, a method which shows the optical properties of the stone's interior to its best advantage by maximizing reflected light which is perceived by the viewer as sparkle. There are many commonly used shapes for faceted stones. The facets must be cut at the proper angles, which varies depending on the optical properties of the gem. If the angles are too steep or too shallow, the light will pass through and not be reflected back toward the viewer. The faceting machine is used to hold the stone onto a flat lap for cutting and polishing the flat facets.[21] Rarely, some cutters use special curved laps to cut and polish curved facets.

Colors
Nearly 300 variations of diamond color exhibited at the Aurora display at the Natural History Museum in London.

The color of any material is due to the nature of light itself. Daylight, often called white light, is all of the colors of the spectrum combined. When light strikes a material, most of the light is absorbed while a smaller amount of a particular frequency or wavelength is reflected. The part that is reflected reaches the eye as the perceived color. A ruby appears red because it absorbs all the other colors of white light, while reflecting the red.

A material which is mostly the same can exhibit different colors. For example, ruby and sapphire have the same primary chemical composition (both are corundum) but exhibit different colors because of impurities. Even the same named gemstone can occur in many different colors: sapphires show different shades of blue and pink and "fancy sapphires" exhibit a whole range of other colors from yellow to orange-pink, the latter called "padparadscha sapphire".[22]

This difference in color is based on the atomic structure of the stone. Although the different stones formally have the same chemical composition and structure, they are not exactly the same. Every now and then an atom is replaced by a completely different atom, sometimes as few as one in a million atoms. These so-called impurities are sufficient to absorb certain colors and leave the other colors unaffected.

For example, beryl, which is colorless in its pure mineral form, becomes emerald with chromium impurities. If manganese is added instead of chromium, beryl becomes pink morganite. With iron, it becomes aquamarine.

Some gemstone treatments make use of the fact that these impurities can be "manipulated", thus changing the color of the gem.[6]

Treatment

Gemstones are often treated to enhance the color or clarity of the stone. Depending on the type and extent of treatment, they can affect the value of the stone. Some treatments are used widely because the resulting gem is stable, while others are not accepted most commonly because the gem color is unstable and may revert to the original tone.[23]

Heat

Heat can either improve or spoil gemstone color or clarity. The heating process has been well known to gem miners and cutters for centuries, and in many stone types heating is a common practice. Most citrine is made by heating amethyst, and partial heating with a strong gradient results in “ametrine” – a stone partly amethyst and partly citrine. Aquamarine is often heated to remove yellow tones, or to change green colors into the more desirable blue, or enhance its existing blue color to a deeper blue.[24]

Nearly all tanzanite is heated at low temperatures to remove brown undertones and give a more desirable blue / purple color.[25] A considerable portion of all sapphire and ruby is treated with a variety of heat treatments to improve both color and clarity.

When jewelry containing diamonds is heated (for repairs) the diamond should be protected with boric acid; otherwise the diamond (which is pure carbon) could be burned on the surface or even burned completely up. When jewelry containing sapphires or rubies is heated, those stones should not be coated with boracic acid (which can etch the surface) or any other substance. They do not have to be protected from burning, like a diamond (although the stones do need to be protected from heat stress fracture by immersing the part of the jewelry with stones in water when metal parts are heated).

Radiation

Virtually all blue topaz, both the lighter and the darker blue shades such as "London" blue, has been irradiated to change the color from white to blue. Most greened quartz (Oro Verde) is also irradiated to achieve the yellow-green color. Diamonds are irradiated to produce fancy-color diamonds (which can occur naturally, though rarely in gem quality).

Waxing/oiling

Emeralds containing natural fissures are sometimes filled with wax or oil to disguise them. This wax or oil is also colored to make the emerald appear of better color as well as clarity. Turquoise is also commonly treated in a similar manner.

Fracture filling

Fracture filling has been in use with different gemstones such as diamonds, emeralds and sapphires. In 2006 "glass filled rubies" received publicity. Rubies over 10 carats (2 g) with large fractures were filled with lead glass, thus dramatically improving the appearance (of larger rubies in particular). Such treatments are fairly easy to detect.

Synthetic and artificial gemstones

Synthetic gemstones are distinct from imitation or simulated gems.

Synthetic gems are physically, optically, and chemically identical to the natural stone, but are created in a laboratory.[26] Imitation or simulated stones are chemically different from the natural stone, but may appear quite similar to it; they can be more easily-manufactured synthetic gemstones of a different mineral (spinel), glass, plastic, resins, or other compounds.

Examples of simulated or imitation stones include cubic zirconia, composed of zirconium oxide, synthetic moissanite, and un-colored, synthetic corrundum or spinels; all of which are diamond simulants. The simulants imitate the look and color of the real stone, but possess neither their chemical nor physical characteristics. In general, all are less hard than diamond. Moissanite actually has a higher refractive index than diamond, and when presented beside an equivalently sized and cut diamond will show more "fire".

Cultured, synthetic, or "lab-created" gemstones are not imitations: The bulk mineral and trace coloring elements are the same in both. For example, diamonds, rubies, sapphires, and emeralds have been manufactured in labs that possess chemical and physical characteristics identical to the naturally occurring variety. Synthetic (lab created) corrundum, including ruby and sapphire, is very common and costs much less than the natural stones. Small synthetic diamonds have been manufactured in large quantities as industrial abrasives, although larger gem-quality synthetic diamonds are becoming available in multiple carats.[27]

Whether a gemstone is a natural stone or synthetic, the chemical, physical, and optical characteristics are the same: They are composed of the same mineral and are colored by the same trace materials, have the same hardness and density and strength, and show the same color spectrum, refractive index, and birefringence (if any). Lab-created stones tend to have a more vivid color, since impurities common in natural stones are not present in a synthetic stone. Synthetics are made free of common naturally occurring impurities that reduce gem clarity or color, unless intentionally added in order to provide a more drab, natural appearance, or to deceive an assayer. On the other hand, synthetics often show flaws not seen in natural stones, such as minute particles of corroded metal from lab trays used during synthesis.

List of rare gemstones
  • Painite was discovered in 1956 in Ohngaing in Myanmar. The mineral was named in honor of the British gemologist Arthur Charles Davy Pain. In 2005, painite was described by the Guinness Book of World Records as the rarest gem mineral on earth.[28]
  • Hibonite was discovered in 1956 in Madagascar. It was named after the discoverer the French geologist Paul Hibon. Gem quality hibonite has been found only in Myanmar.[29]
  • Red beryl or bixbite was discovered in an area near Beaver, Utah in 1904 and named after the American mineralogist Maynard Bixby.
  • Jeremejevite was discovered in 1883 in Russia and named after its discoverer, Pawel Wladimirowich Jeremejew (1830–1899).
  • Chambersite was discovered in 1957 in Chambers County, Texas, US, and named after the deposit's location.
  • Taaffeite was discovered in 1945. It was named after the discoverer, the Irish gemologist Count Edward Charles Richard Taaffe.
  • Musgravite was discovered in 1967 in the Musgrave Mountains in South Australia and named for the location.
  • Grandidierite was discovered by Antoine François Alfred Lacroix (1863–1948) in 1902 in Tuléar province, Madagascar. It was named in honor of the French naturalist and explorer Alfred Grandidier (1836–1912).
  • Poudretteite was discovered in 1965 at the Poudrette Quarry in Canada and named after the quarry's owners and operators, the Poudrette family.
  • Serendibite was discovered in Sri Lanka by Dunil Palitha Gunasekera in 1902 and named after Serendib, the old Arabic name for Sri Lanka.
  • Zektzerite was discovered by Bart Cannon in 1968 on Kangaroo Ridge near Washington Pass in Okanogan County, Washington, USA. The mineral was named in honor of mathematician and geologist Jack Zektzer, who presented the material for study in 1976.
gollark: I really like the 2nd.
gollark: 2nd!
gollark: Concrete cuboids fit in everywhere.
gollark: Cool! Is it in ShutdownOS now?
gollark: /playerinfo perhaps.

See also

References
  1. "Gemstone". Lexico. Oxford University Press.
  2. Webster Online Dictionary Archived 2007-06-03 at the Wayback Machine
  3. Alden, Nancy (2009). Simply Gemstones: Designs for Creating Beaded Gemstone Jewelry. New York, NY: Random House. p. 136. ISBN 978-0-307-45135-4.
  4. Precious Stones, Max Bauer, p. 2
  5. Wise, R. W., 2006, Secrets Of The Gem Trade, The Connoisseur's Guide To Precious Gemstones, Brunswick House Pr, pp. 3–8 ISBN 0-9728223-8-0
  6. Frangoulis, George (18 April 2015). "GEM HUNTER". Lulu.com.
  7. AskOxford.com Concise Oxford English dictionary online.
  8. Desirable diamonds: The world's most famous gem. by Sarah Todd.
  9. Wise, R. W., 2006, Secrets of The Gem Trade, The Connoisseur's Guide To Precious Gemstones, Brunswick House Pr, p.36 ISBN 0-9728223-8-0
  10. Wise, R. W., 2006, Secrets Of The Gem Trade, The Connoisseur's Guide To Precious Gemstones, Brunswick House Pr, p. 15
  11. Burnham, S.M. (1868). Precious Stones in Nature, Art and Literature. Bradlee Whidden. Page 251 URL: Helen of Troy and star corundum Archived 2010-10-13 at the Wayback Machine
  12. Church, A.H. (1905). "Definition of Precious Stones". Precious Stones considered in their scientific and artistic relations. His Majesty's Stationery Office, Wyman & Sons. p. 11. Archived from the original on 2007-09-29 – via Farlang.com.
  13. Secrets of the Gem Trade; The Connoisseur's Guide to Precious Gemstones, Richard W Wise, Brunswick House Press, Lenox, Massachusetts., 2003
  14. "5 Most Precious Stones". HowStuffWorks.com. 2009-11-09. Archived from the original on 2014-11-06.
  15. "A complete guide to Gemstones". Jewellery Monthly. 2015-04-02. Archived from the original on 2017-08-28.
  16. "Artificial treatment of gemstones". Dictionary of Gems and Gemology. Berlin, Heidelberg: Springer Berlin Heidelberg. 2009. pp. 50. doi:10.1007/978-3-540-72816-0_1308. ISBN 9783540727958.
  17. Katz, Michael (2005). Gemstone Energy Medicine: Healing Body, Mind and Spirit. Natural Healing Press. ISBN 9780924700248. Retrieved 2020-04-06.
  18. "The Gem and Jewelry Institute of Thailand (Public Organization)". Bangkok Post.
  19. "Rapaport report of ICA Gemstone Conference in Dubai". Diamonds.net. 2007-05-16. Archived from the original on 2011-07-26. Retrieved 2010-07-30.
  20. Kraus, Pansy D. (2007). Introduction to Lapidary. Krause Publications. ISBN 9780801972669.
  21. Vargas, Glenn; Vargas, Martha (2002). Faceting For Amateurs. ISBN 9780917646096.
  22. "Padparadscha Sapphires : 10 Tips On Judging The Rare Gem". The Natural Sapphire Company Blog. 2015-04-06. Retrieved 2018-01-19.
  23. Gemstone Enhancement: History, Science and State of the Art by Kurt Nassau
  24. Nassau, Kurt (1994). Gem Enhancements. Butterworth Heineman.
  25. "Tanzanite heating - the science". Archived from the original on 20 June 2016.
  26. Jewelers' circular-keystone: JCK. Chilton Company. 1994.
  27. "New process promises bigger, better diamond crystals". Carnegie Institution for Science. Archived from the original on 1 December 2010. Retrieved 7 January 2011.
  28. Folkard, Claire; Freshfield, Jackie; Masson, Carla; Dimery, Rob (12 December 2017). "Guinness World Records 2005". Guinness World Records Limited.
  29. "HIBONITE: A NEW GEM MINERAL" (PDF).
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.