New South Wales AD60 class locomotive

The AD60 class were Beyer-Garratt patent articulated four-cylinder, simple, non-condensing, coal-fired superheated, 4-8-4+4-8-4 heavy goods steam locomotives built by Beyer, Peacock and Company for the New South Wales Government Railways in Australia.

New South Wales AD60 class
6012 at the top of Cowan Bank
Type and origin Power type Steam Builder Beyer, Peacock and Company Manchester Serial number 7473–7497, 7528–7549 Build date 1952–1954, 1956 Total produced 42 (plus 5 as spares)
Specifications Configuration: ​  • Whyte 4-8-4+4-8-4 Gauge 4 ft 8 ^1⁄2 in (1,435 mm) Driver dia. 4 ft 7 in (1.397 m) Length 108 ft 7 in (33.096 m) Adhesive weight 282,000 lb (128,000 kg) later 317,000 lb (144,000 kg) Loco weight 562,000 lb (255,000 kg) later 582,000 lb (264,000 kg) Fuel type Coal Fuel capacity 14 long tons (14.2 t; 15.7 short tons) later 18 long tons (18.3 t; 20.2 short tons) Firebox:  • Firegrate area 65 sq ft (6.0 m^2) Boiler pressure 200 psi (1.38 MPa) Heating surface 3,030 sq ft (281 m^2) Superheater: ​  • Heating area 750 sq ft (70 m^2) Cylinders Four Cylinder size 19.25 in × 26 in (489 mm × 660 mm) later 19.875 in × 26 in (505 mm × 660 mm) Valve gear Walschaerts
Performance figures Tractive effort 59,560 lbf (264.9 kN) later 63,490 lbf (282.4 kN) Factor of adh. 4.73 or 4.99
Career Operators New South Wales Government Railways Class AD60 Number in class 42 Numbers 6001–6042 First run July 1952 Last run March 1973 (in service) Preserved 6029, 6039, 6040, 6042 Disposition 4 preserved, 38 scrapped

Design

AD60 Class Fittings and Controls

AD60 Beyer-Garratt Boiler

The AD60 Class 4-8-4+4-8-4 Beyer-Garratt patent consists of a boiler carried on a separate frame in the centre of the locomotive and supported by the frames of the two engines, one at each end. The locomotive thus consists of three parts: a water tank, a fixed chassis supporting a boiler and a rear engine unit carrying a coal bunker and water tank. The standard gauge coupled axle loading of 16 long tons (16.3 t; 17.9 short tons) and able to negotiate 6-chain (120 m) curves.

The design incorporated the most modern technology to minimise maintenance and repairs, including:

• integral cast steel engine bed frames incorporating the cylinders
• large steel boiler with roundtop firebox and flexible stays
• mechanical stoker
• roller bearings fitted to bogie, coupled wheels and crankpins
• valve gear operated by Hadfield powered reversing gear

Introduction

This was the only type of Garratt locomotive to operate on the New South Wales Government Railways. Designed to a light axle load of only 16 long tons (16.3 t; 17.9 short tons), they were intended for hauling feeder branch-line services to the main lines where heavier main-line locomotives could continue with the load.[1][2][3]

In 1949 twenty-five were initially ordered from Beyer, Peacock and Company, followed by a further twenty-five. Following a change of policy in favour of diesel traction, negotiations were entered into, in order to cancel the last part of the order. Forty-two complete locomotives were delivered, together with spare parts equating to approximately five further locomotives. The five sets of parts did not include engine unit frames. The cancellation contract stipulated that the NSWGR could not assemble the spare parts into complete locomotives without paying substantial royalties to Beyer-Peacock. The last three locomotives were cancelled completely and the assembly positions at the Gorton Works of Beyer-Peacock were sold to the South African Railways.

The locomotives were delivered in their five major component pieces: Front engine, rear engine, boiler-cab, rear bunker and front water tank. These five sub assemblies were built into a complete locomotive in NSW.

Locomotive 6002 was the first to enter service in July 1952 with the last, 6040 delivered on 2 January 1957.[1][3] The locomotives were the most powerful to operate in Australia but behind the D57 in terms of tractive effort.[4]

Improvements

Early trials established that the 14-long-ton (14.2 t; 15.7-short-ton) bunker was insufficient to allow the locomotives to operate from Enfield to Goulburn resulting in the bunkers being enlarged to carry 18 long tons (18 t; 20 short tons). Ventilation of the cabs caused considerable concern. Consequently, the class was banned from working through single-line tunnels, this ban also being in response to the difficulty crews would have climbing out in the event of failure within such tunnels. Amongst attempts to improve cab ventilation, 6011 was experimentally fitted in September 1952 with a large tube along the front bunker and boiler to funnel air from the front of the locomotive into the cab. It was unsuccessful and was removed in 1955. Some improvement was obtained by running the locomotives bunker first.[3]

Owing to the length and noise of the locomotive, crews found difficulty in hearing warning detonators. To rectify the situation, tubes were fitted to convey the sound from the leading wheels to the cab. This mechanism can still be seen today on 6040 at the NSW Rail Museum.[3]

When it became apparent that the Garratts would see more service on main lines than on the lighter branch lines, it was decided to increase the tractive effort of a number of the class by enlarging the cylinder diameter and by altering the weight distribution by removing liners from the bogies. This increased the axleload on each of the driving wheels by approximately 2 long tons (2.0 t; 2.2 short tons) with 30 locomotives treated. To distinguish these improvements the double plus sign ++ was painted after the number and they were nicknamed Super Garratts. These 30 were also fitted with dual controls for bunker first running and denoted DC. To accommodate them, 105-foot (32 m) turntables were installed at Broadmeadow, Enfield and Werris Creek depots.[3]

In September 1968, the highest numbered member of the class, 6042, although only eleven years old, was nearing the end of its service life and due to the policy of dieselisation, was scheduled for withdrawal rather than overhaul. However, with a need still for Garratts, Cardiff Locomotive Workshops assembled a Class 60 from spares it had on hand. Cardiff Workshops also wanted to show that a steam locomotive could be overhauled just as quickly or quicker than a diesel locomotive. In order to avoid paying the assembly royalties stipulated by Beyer - Peacock in the cancellation contract, it was decided to number the new locomotive "6042". For a very brief period there were two 6042's in existence until the original was hauled away and scrapped. However, the "new" 6042 carried the Beyer Peacock builders plates for 6043 (builder number 7545) for the next five years.[5]

Operation

The class initially entered service on the Main North and Main South and later Main Western line as far as Dubbo and Parkes. Because of their light axle load they were cleared to operate on the Crookwell, Captains Flat, Temora, Narrandera and Bourke lines.[1]

Typical workings in the mid 1960s would consist of bulk export coal and general goods movements :

Typical Class AD60 Traffic
Route	Traffic	Down (tons)	Up (tons)	Notes
Glenlee to Rozelle	Export Coal	1500
Gosford to Broadmeadow	Export Coal	1500		double headed AD60's
Gosford to Broadmeadow	General Freight	685 single	1100 assisted
Broadmeadow to Muswellbrook	General Freight	775	1150
Newstan/Awaba Colliery to Wangi PS	Export Coal	1075	1500T	assisted
Enfield to Goulburn	General Freight	900	1500
From Botany Oil Refineries	Petroleum	1000
Goulburn to Captains Flat	Mineral	600	600
Junee	Goods	600	600
Cootamundra to Stockinbingal	Goods	1000	1500
Up to Lithgow				assisting until electrification in 1957
Parkes to Goobang Junction	Goods	1000	1400	16T axle loading locos only
Dubbo to Merrygeen	Goods	1100	1000	16T axle loading locos only
Parkes to Bogan Gate/Tottenham	Goods	1000	1400	16T axle loading locos only
Portland to Pipers Flat	Cement	700
Pipers Flat to Wallerawang	Cement	1400
Dubbo to Werris Creek	Goods	1100
Lithgow to Bathurst	Goods	850	900
Orange to Parkes	Goods	600
Bathurst westward	Goods	850	900	dependent on grade
W44 Broken Hill	concentrates	575	600	double headed AD60's
Molong to Orange	Goods	600	600	double headed AD60's

Demise & preservation

6012 was the first of the class to be withdrawn in 1955. The next few to be withdrawn suffered accident damage in major collisions in 1961 (6003 Guerie) and 1963 (6028 Glenlee - rebuilt and returned to service by 1965). Dieselisation accounted for the other 40 (or 41) of the class from 1965. The last withdrawn was the replacement "6042" built in 1968 which operated the final New South Wales Government Railways steam service on 22 February 1973. Just five years old, it was also the natural choice to work a ceremonial end to steam working for State Government officials on 2 March 1973.

Preserved AD60 Class Locomotives
No.	Year	Current Organisation	Location	Status	Ref
6029	1956	Privately Owned	Thirlmere	Operational
6039	1956	Dorrigo Steam Railway & Museum	Dorrigo	Stored	Dorrigo Webpage
6040	1956	Transport Heritage NSW	Thirlmere	Static Exhibit	NSW Locomotive, Steam 6040
"6042"	1968	Dorrigo Steam Railway & Museum	Forbes	Stored	[6] Dorrigo Webpage

References

1. Oberg, Leon (1984). Locomotives of Australia 1850's - 1980's. Frenchs Forest: Reed Books. pp. 204–206. ISBN 0 730100 05 7.
2. Oberg, Leon (2007), Locomotives of Australia, 1854 to 2007 (4th ed.), Rosenberg Publishing, pp. 261–263, ISBN 978-1-877058-54-7
3. Grunbach, Alex (1989). A Compendium of New South Wales Steam Locomotives. Sydney: Australian Railway Historical Society, NSW Division. pp. 241–247. ISBN 0 909650 27 6.
4. Powerhouse Museum. "Sectioned Beyer Garratt locomotive model 6001". Powerhouse Museum, Australia. Retrieved 1 June 2014.
5. "20 Years Ago" Railway Digest September 1988 page 358
6. "Forbes Vintage Village Auction" Railway Digest January 1987 page 27

Further reading

• Gilbertson, CB (April 2003). "Remembering the 60 Class". Australian Railway History Bulletin. pp. 123–135.

External links

Media related to New South Wales AD60 class locomotives at Wikimedia Commons