NICAM

Near Instantaneous Companded Audio Multiplex (NICAM) is an early form of lossy compression for digital audio. It was originally developed in the early 1970s for point-to-point links within broadcasting networks.[1] In the 1980s, broadcasters began to use NICAM compression for transmissions of stereo TV sound to the public.

This article is about a compression form for digital audio. For the media content rating institute, see Netherlands Institute for the Classification of Audiovisual Media.

History

Near-instantaneous companding

The idea was first described in 1964. In this, the 'ranging' was to be applied to the analogue signal before the analogue-to-digital converter (ADC) and after the digital-to-analogue converter (DAC).[2] The application of this to broadcasting, in which the companding was to be done entirely digitally after the ADC and before the DAC, was described in a 1972 BBC Research Report. [3]

NICAM was originally intended to provide broadcasters with six high-quality audio channels within a total bandwidth of 2048 kbit/s. This figure was chosen to match the E1 primary multiplex rate, and systems using this rate could make use of the planned PDH national and international telecommunications networks.

Several similar systems had been developed in various countries, and in about 1977/78 the BBC Research Department conducted listening tests to evaluate them. The candidates were:

  • A RAI system which used A-law companding to compress 14-bit linear PCM samples into 10 bits (14:10)
  • A NICAM-type system proposed by Télédiffusion de France (14:9)
  • NICAM-1 (13:10)
  • NICAM-2 (14:11)
  • NICAM-3 (14:10)

It was found that NICAM-2 provided the best sound quality, but reduced programme-modulated noise to an unnecessarily low level at the expense of bit rate. NICAM-3, which had been proposed during the test to address this, was selected as the winner.[4][5]

Audio is encoded using 14 bit pulse-code modulation at a sampling rate of 32 kHz.

Broadcasts to the public

NICAM's second role – transmission to the public – was developed in the 80s by the BBC. This variant was known as NICAM-728, after the 728 kbit/s bitstream it is sent over. It uses the same audio coding parameters as NICAM-3.

The first NICAM digital stereo programme was the First Night of the 92nd edition of the Proms which was broadcast on BBC2 from the Crystal Palace transmitting station in London on 18 July 1986, though programmes were not advertised as being broadcast in stereo on the BBC until some five years later, when the majority of the country's transmitters had been upgraded to broadcast NICAM, and a large number of BBC programmes were being made in stereo.

The BBC publicly launched their NICAM stereo service in the United Kingdom on Saturday 31 August 1991 (see 1991 in television) though other UK broadcasters ITV and Channel 4 advertised this capability some months earlier. Channel 4 began tests much earlier in February 1989 via the Crystal Palace transmitter in London.

It has been standardized as ETS EN 300 163.[6]

Nations using NICAM public broadcasts

Several European countries (as well as one Asian country) have implemented NICAM with the PAL and SECAM TV systems[7][8][9]

Some Asia-Pacific nations have implemented NICAM

  • Hong Kong (commonly used for dual language for programming containing both Cantonese and English/Mandarin/Japanese/Korean soundtracks; planned to cease by 2020 when digital TV broadcasting transition is complete and analogue TV transmissions will be stopped)
  • Singapore (Full switchover to DVB-T2 and DVB-C complete by 1 January 2019. NICAM became historical from that date.)
  • Macau
  • Guangzhou
  • Beijing (BTV)
  • South Africa (SABC1, SABC2, etv)
  • Malaysia
    • Used by TV1, TV2, ntv7, 8TV, and TV9 around Klang Valley. TV3 also uses NICAM on their VHF transmission frequency (Channel 12) in the Klang Valley, but uses Zweikanalton on their UHF transmission frequency (Channel 29).
  • New Zealand (Full switchover to DVB-T complete by 1 December 2013. NICAM became historical from that date.)
  • Indonesia
    • Television stations in Indonesia use NICAM Stereo for analogue television. Full switchover to DVB-T2 is expected to complete by 2020 by which all analogue broadcasting have ceased.
  • Thailand
    • Used on Channel 3 and Channel 9 MCOT HD (Except Thai PBS usually broadcast in stereo but analog broadcast has been cease on 16 June 2018; Switched to terrestrial DVB-T2)

Some other countries use Zweikanalton analogue stereo instead. Analogue stereo conversion thus begins.

Operation

In order to provide mono "compatibility", the NICAM signal is transmitted on a subcarrier alongside the sound carrier. This means that the FM or AM regular mono sound carrier is left alone for reception by monaural receivers.

A NICAM-based stereo-TV infrastructure can transmit a stereo TV programme as well as the mono "compatibility" sound at the same time, or can transmit two or three entirely different sound streams. This latter mode could be used to transmit audio in different languages, in a similar manner to that used for in-flight movies on international flights. In this mode, the user can select which soundtrack to listen to when watching the content by operating a "sound-select" control on the receiver.


This is the spectrum of NICAM on the PAL system. On the SECAM L system, the NICAM sound carrier is at 5.85 MHz, before the AM sound carrier, and the video bandwidth is reduced from 6.5 MHz to 5.5 MHz.

NICAM currently offers the following possibilities. The mode is automatically selected by the inclusion of a 3-bit type field in the data stream.

  • One digital stereo sound channel.
  • Two completely different digital mono sound channels.
  • One digital mono sound channel and a 352 kbit/s data channel.
  • One 704 kbit/s data channel.

The four other options could be implemented at a later date. Only the first two of the ones listed are known to be in general use however.

NICAM packet transmission

The NICAM packet (except for the header) is scrambled with a nine-bit pseudo-random bit-generator before transmission.

  • The topology of this pseudo-random generator yields a bitstream with a repetition period of 511 bits.
  • The pseudo-random generator's polynomial is:
  • The pseudo-random generator is initialized with:

Making the NICAM bitstream look more like white noise is important because this reduces signal patterning on adjacent TV channels.

  • The NICAM header is not subject to scrambling. This is necessary so as to aid in locking on to the NICAM data stream and resynchronisation of the data stream at the receiver.
  • At the start of each NICAM packet the pseudo-random bit generator's shift register is reset to all ones.

NICAM transmission issues


There are some latent issues involved with the processing of NICAM audio in the transmission chain.

  • NICAM (unlike the Compact Disc standard) samples 14-bit audio at 32 kHz.
  • The upper frequency limit of a NICAM sound channel is 15 kHz due to anti-aliasing filters at the encoder.
  • The original 14-bit PCM audio samples are companded digitally to 10 bits for transmission.
  • NICAM audio samples are divided into blocks of 32. If all the samples in a block are quiet, such that the most significant bits are all zeros, these bits can be discarded at no loss.
  • On louder samples some of the least significant bits are truncated, with the hope that they will be inaudible.
  • A 3-bit control signal for each block records which bits were discarded.
  • Digital companding (using a CCITT J.17 pre-emphasis curve) ensures that the encoding and decoding algorithms can track perfectly.

NICAM carrier power

ITU (and CCITT) standards specify that the power level of the NICAM signal should be at -20 dB with respect to the power of the vision carrier.

  • The level of the FM mono sound carrier must be at least -13 dB.
  • Measuring the modulation level of the NICAM signal is difficult because the QPSK NICAM carrier waveform (unlike AM or FM modulated carrier waveforms) is not emitted at a discrete frequency.

When measured with spectrum analyser the actual level of the carrier (L) can be calculated using the following formula:

L(NICAM) = L(Measured) + 10 log (R/BWAnalyser) + K

  1. L(NICAM) = actual level of the NICAM carrier [dBμV]
  2. L(Measured) = measured level of the NICAM carrier [dBμV]
  3. R = -3 dB bandwidth of the signal [kHz]
  4. BWAnalyser = bandwidth of the spectrum analyser [kHz]
  5. K = logarithmic form factor of the spectrum analyser ~2 dB

note: if BWAnalyser is greater than R, the formula becomes L(NICAM) = L(Measured) + K

Differing features

NICAM sampling is not standard PCM sampling, as commonly employed with the Compact Disc or at the codec level in MP3, AAC or Ogg audio devices. NICAM sampling more closely resembles Adaptive Differential Pulse Code Modulation, or A-law companding with an extended, rapidly modifiable dynamic range.

Two's complement signing

The two's complement method of signing the samples is used,[10] so that:

  • 01111111111111 represents positive full-scale
  • 10000000000000 represents negative full-scale

±0 V has three binary representations
  • 00000000000001 represents 0 V, with no +/- distinction. This may have originated as a method to reduce the emergence of DC patterns from transmission of silent material.
  • 00000000000000 represents 0 V, with no +/- distinction
  • 11111111111111 represents 0 V, with no +/- distinction

Parity checking limited to only 6 of 10 bits

In order to strengthen parity protection for the sound samples, the parity bit is calculated on only the top six bits of each NICAM sample. Early BBC NICAM research showed that uncorrected errors in the least significant four bits were preferable to the reduced overall protection offered by parity-protecting all ten bits.

Recording

VCR
Main article: Videocassette recorder

VHS and Betamax home videocassette recorders (VCRs) initially only recorded the audio tracks by means of a fixed linear recording head, which was inadequate for recording NICAM audio; this significantly limited their sound quality. Many VCRs later included high quality stereo audio recording as an additional feature, in which the incoming high quality stereo audio source (typically FM radio or NICAM TV) was frequency modulated and then recorded, in addition to the usual audio and video VCR tracks, using the same high-bandwidth helical scanning technique used for the video signal. Full-size VCRs already made full use of the tape, so the high quality audio signal was recorded diagonally under the video signal, using additional helical scan heads and depth multiplexing. The mono audio track (and on some machines, a non-NICAM, non-Hi-Fi stereo track) was also recorded on the linear track, as before, to ensure backwards-compatibility of recordings made on Hi-Fi machines when played on non-Hi-Fi VCRs.

Such devices were often described as "HiFi audio", "Audio FM" / "AFM" (FM standing for "Frequency Modulation") and sometimes informally as "Nicam" VCRs (due to their use in recording the Nicam broadcast audio signal). They remained compatible with non-HiFi VCR players since the standard audio track was also recorded, and were at times used as an alternative to audio cassette tapes due to their superior frequency range and flat frequency response.

DVD

While recording in video mode (compatible with DVD-Video), most DVD recorders can only record one of the three channels (Digital I, Digital II, Analogue mono) allowed by the standard. Newer standard such as DVD-VR allows recording all the digital channels (in both stereo and bilingual mode), whereas the mono channel will be lost.

Flash memory and computer multimedia

Codecs for digital media on computers will often convert NICAM to another digital audio format to compress drive space.

gollark: q
gollark: Check the method reference.
gollark: It is in the documentation.
gollark: `canvas3d`
gollark: Or automatic mining, even.

See also

References
  1. Croll, M.G., Osborne, D.W. and Spicer, C.R. (1974), Digital sound signals: the present BBC distribution system and a proposal for bit-rate reduction by digital companding. IEE Conference publication No. 119, pp. 90–96
  2. Bartlett, C.J.C. and Greszczuk, J. (1964), Companding in a p.c.m. system. Symposium on Transmission Aspects of Communication Networks, London, IEE 1964, pp. 183–186.
  3. Osborne, D.W. (1972) Digital sound signals: further investigation of instantaneous and other rapid companding systems. BBC Research Dept. Report 1972/31.
  4. Jones, A.H. (1978), Digital coding of audio signals for point-to-point transmission. IEE Conference Publication No. 166, pp. 25–28
  5. Gilchrist, N.H.C. (1978), Digital sound signals: tests to compare the performance of five companding systems for high-quality sound signals. BBC Research Department Report 1978/26.
  6. ETSI ETS EN 300 163, (previously: EBU T 3266)
  7. "Broadcasting System Details". University of Surrey – Department of Electronic Engineering. Archived from the original on December 5, 2010. Retrieved 2007-08-30.
  8. Analogue TV technologies
  9. World-Wide T.V. Standards
  10. Steve Hosgood. ""All You Ever Wanted to Know About NICAM but were Afraid to Ask"". Archived from the original on February 14, 2005. Retrieved 2007-08-30.

Further reading

Related websites or technical explanations

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.