Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [lom]

13 questions
8
votes
1 answer

LOM vs. NIC for iDRAC with Dell PowerEdge R720xd

I'm trying to get going with iDRAC 7 Express (no Enterprise license so we can't use the dedicated port). In the setup menu for iDRAC, it asks to choose which network interface to use for iDRAC. There are four choices: LOM1, LOM2, LOM3, and LOM4. …
CptSupermrkt
  • 233
  • 1
  • 3
  • 9
5
votes
1 answer

Resetting SP password using jumper P20 doesn't work on Sun Fire x4600 M2

The Sun Fire X4600 M2 Servers Service Manual says installing a shorting jumper across the P20 header pins will reset the SP password and clear the BIOS password. I installed the jumper then powered up the SP and the system fully as this note…
aculich
  • 3,520
  • 1
  • 25
  • 33
3
votes
1 answer

Identify and/or clear alarm on Sunfire X4200 via ILOM

I've got a customer with a remotely-hosted X4200 and all they know is that there is an amber alarm light on the front of the server. I've been asked to identify the offending component (if any) and clear the alarm if it's nothing to worry about. …
Temp Sun Support Guy
  • 31
  • 3
2
votes
2 answers

In hponcfg for iLO config, what's the difference between "YES" and "LOM" for "SHARED_NETWORK_PORT"?

If you get your iLO network settings using hponcfg for an HPe server - there is a setting called SHARED_NETWORK_PORT - with values of NO, YES, LOM, or FlexibleLOM. I am trying to determine what the actual difference is between the values of YES and…
Protonus
  • 41
  • 2
  • 6
1
vote
0 answers

Cisco CIMC "forgets" settings on power loss

I have a Cisco UCS C200 M2 server, and CIMC forgets every setting(which NIC to use, IP settings, admin password, etc)when the server is unplugged. I replaced the CMOS battery on the motherboard, and it didn't solve the problem.
Máté Varga
  • 11
  • 1
1
vote
1 answer

Sparc T5240 ILOM password grief

I'm trying to reset the ILOM root password on a SPARC Enterprise T5240. Neither of the 2 methods described below work for me, so I'm after further suggestions (short of guessing the root password - I've been trying that!). Method 1 - Jumper…
Plutext
  • 143
  • 1
  • 9
1
vote
3 answers

log in to v20z console using serial management

I have a Netra T1 (SPARC) which has LOM that enable to log in to the OS console locally for troubleshooting without plug in a monitor and keyboard. I also have a SunFire V20z (x86) which has a SP. However I do not find any equivalent command to…
conandor
  • 229
  • 3
  • 7
  • 18
1
vote
2 answers

Find the reason of why does Sunfire V100 (SunOS 5.9) server not start

I have a Sunfire V100 (SunOS 5.9) server which was working fine till 14th February 2014. After that day we can not access this server. Today I was able to connect server through a console and I got the following message on the hyper terminal of a…
Amit Raj
  • 111
  • 6
1
vote
3 answers

Sun LOM alerts

I'm monitoring Sun hardware using SNMP to gather information from the LOM card. One of the datapoints I'm monitoring is a voltage status MIB which alerts if any of the internal voltages becomes too high or low - with the thresholds being set,…
Jon Topper
  • 802
  • 9
  • 17
1
vote
1 answer

Does ILOM on recent Sun rackmount servers fully support Linux?

Do the recent Sun rackmount servers with ILOM fully support installation of Linux (Ubuntu or Fedora maybe) via the ILOM (connected by ssh) without having to hook up a display, kbd, and mouse? I have an old Sun v20z right now that will install…
orange80
  • 198
  • 2
  • 12
0
votes
2 answers

Sun LOM KVM not working on Linux

I have a set of SunFire X2100 and X2200 servers. If I attempt to use the remote KVM feature from my Ubuntu Linux box, the Java app loads and attempts to connect but receives an "Authentication Error" message. The same thing works fine from a…
Jon Topper
  • 802
  • 9
  • 17
0
votes
1 answer

HP FlexFabric 10Gb 2-Port 534FLB Adapter and vSphere 6.5

we have an HP C3000 blade enclosure equipped with 2 ProLiant BL460c Gen8 each with 1x HP FlexFabric 10Gb 2-Port 534FLB Adapter and 1x HP Flex-10 10Gb 2-port 530M Adapter. On interconnect bay 1 we have a HP 6125G/XG Blade Switch. Our problem is that…
Mihai Magdalin
  • 3
  • 1
0
votes
1 answer

Set boot device / access console (Dell iDRAC 8) using modern Linux

I have a Dell PowerEdge R730xd which I can only access using the iDRAC 8 web interface. I'm unable to launch the Java (JNLP) virtual console, which might be necessary to fix the issue. I'm also unable to access the SSH feature of the iLOM due to…
C-Otto
  • 294
  • 5
  • 16