Mark 10 torpedo

The Mark 10 torpedo was a torpedo put into use by the United States in 1915. It was derived from the Mark 9 aircraft torpedo converted to submarine use.[3] It was used as the primary torpedo in the R- and S-class submarines.[4] It used alcohol-water steam turbine propulsion.[5] It was succeeded by the problematic Mark 14 torpedo, but remained in service in S-boats & fleet submarines through the Pacific War.[6] The Mark 10 featured the largest warhead (497 lb (225 kg) of TNT) of any U.S. torpedo developed at that time.[1] Stockpiles of Mark 10 Mod 3 torpedoes were used extensively during the first part of World War II due to short supply of the newer and longer (246 in (6.2 m) Mark 14s, with some fleet submarines carrying a mixture of both types on patrol.[7]

Mark 10 torpedo
Type	Anti-surface ship torpedo[1]
Place of origin	United States
Service history
In service	1915–1945
Used by	United States Navy
Wars	World War II
Production history
Designer	E. W. Bliss Company and Naval Torpedo Station[1]
Designed	1915[1]
Manufacturer	Naval Torpedo Station[1][1]
Variants	Mod 3[2]
Specifications
Mass	2215 pounds[1]
Length	195 inches[1]
Diameter	21 inches[1]
Effective firing range	3500 yards[1]
Warhead	Mk 10 Mod 3, TNT[1]
Warhead weight	497 pounds[1]
Detonation mechanism	Mk 3 contact exploder[1]
Engine	Steam turbine[1]
Propellant	Alcohol[1]
Maximum speed	36 knots[1]
Guidance system	gyro, straight running[1]
Launch platform	Submarines[1]

Mark 10 torpedoes, and those developed at the same time (Mark 9 air- and Mark 8 surface ship-launched) used essentially the same control package (the Ulan gear) as the newer Mark 14 for depth and direction. The running depth could be set to between 5 and 35 m (16 and 115 ft). The gyro angle could be set for a new course up to 90 degrees port or starboard from the current course of the submarine before launch. The Mark 10 would run out of the tube straight ahead for the "reach", then turn to a new, pre-set course, through a total angular targeting of 180 degrees over the end of the submarine, and then run on this intercept course straight to the target.

To use a Mark 10 Mod 3 (the earlier Mark 10 torpedo mod numbers would not work) torpedo in fleet submarine tubes required a gyro angle setting spindle adapter be slipped into the torpedo housing to extend the reach of the spindle into the torpedo. In pre-fleet submarines, the gyro setting machinery was on the outside of the tube,[8] while the fleet submarine gyro spindles are on the inside of the tube.[9]

The Mark 10 torpedo had the same "deep running" problem (where actual running depth was greater than that set before launch) as the Mark 14.[10] By January 5, 1942 the Bureau of Ordnance informed Commander, Submarines, Pacific Fleet the Mark 10 torpedoes ran four feet deeper than set. Because the Mark 10 used Mark 3-1 and Mark 3-3 exploder mechanism with contact-only firing,[11] it suffered none of the problems with prematures or duds the Mark 14 did. However, for a short period at the beginning of the war, the Mark 10 was viewed as more reliable, and in some cases preferred over the Mark 14.

See also

• American 21 inch torpedo

References

1. "Torpedo History: Torpedo Mk10". Retrieved 12 June 2013.
2. "United States of America Torpedoes Pre-World War II". Retrieved 24 June 2013.
3. Naval Underwater Systems Center, Newport, Rhode Island, "History of U.S. Navy Torpedo Development"
4. "Mk 10 Submarine-Launched Anti-Surface Torpedo"
5. "NEWPORT AND NAVY TORPEDOES - AN ENDURING LEGACY" Archived 2010-12-04 at the Wayback Machine
6. Blair, Clay, Jr. Silent Victory (Philadelphia: Lippincott, 1975).
7. United States Submarine Operations in World War II
8. US Navy Ordinance Department. 21 Inch Submerged Torpedo Tube OP 1085. US Navy. Page 90, figure 172.
9. US Navy Ordinance Department (1944). 21 Inch Submerged Torpedo Tube, OP 1086 page 124. US Navy.
10. Roscoe, Theodore. United State Submarine Operations in World War II, p. 253
11. OP 1634, U.S. Navy Torpedoes, General Data 1945, p. 21.