Questions tagged [fan]
57 questions
0
votes
1 answer
HP ML310e Gen8 v2 is really noisy
I have a ML310e Gen8 v2 and a problem on initial setup the server.
The problem is with the Fan noise and speed.
The server is fully updated with the latest firmware available from HP and the setting in BIOS for Thermal Control is set to Optimal.
But…
networkpro
- 61
- 2
- 10
0
votes
1 answer
ProLiant DL120 G7 manually increase fan speed
Because of the applications wich are running on my ProLiant DL120 G7 it has usually high cpu loads. That is no problem, all running very well. But the CPU temp hits 75 degree celsius, and the fan's are just rotating at 50% speed. I would like to…
xattr
- 1
- 1
0
votes
2 answers
Netgear (gsm7224v1) 24-port gigabit switch exhaust fans
I own a Netgear GSM7224v1 (link) 24-port gigabit switch at home. The switch is about 2 years old and works just fine. The two exhaust fans however, are making quite a bit of noise even after I've cleaned them out with an air can, the fans constantly…
osij2is
- 3,875
- 2
- 23
- 31
0
votes
1 answer
Use ipmi to control fan speed on ASRock X570D4U-2L2T server
Problem
I can't use ipmi to control fan speed.
I have an X570D4U-2L2T motherboard with a Ryzen 5600x and am running Ubuntu 21.04.
Can the community advise how I might use ipmitool or ipmiutil to control the fan speeds – either to set a constant…
Jim
- 1
0
votes
1 answer
What to do with a Poweredge 1950 with a failed fan speed sensor?
For some reason (and it's possibly coincidentally suspicious that I needed to get a bit of extra slack on the SATA cable that is wrapped around/under fan module 1, so I gave it a firm pull..) my 1950 PE server is now reporting E1311 and E1313, "Fan…
Caius Jard
- 165
- 1
- 1
- 8
0
votes
1 answer
Server Fans Never Slow Down After Speeding Up
I have a server motherboard in a large tower case with several hard disks installed. It's basically a media server that serves over CIFS.
I'm using the 'sensors' command on Linux to monitor the system temperatures. It typically runs around 70c, but…
kmac.mcfarlane
- 11
- 1
0
votes
1 answer
Hp DL360 G8 fans noise after PCI (GPU) installation
i have a problem After Install a Graphic Card in my Server
When i USE PCI slot my Server fans increase to 40%
and when i Get off Graphic card They return Normal (19%)
I Use This Server as Home Workstation and It is important not to make noise
ILO 4…
-1
votes
1 answer
Intel Xeon server fan
I am building a server from scratch.
I plan on using this box with this motherboard and this processor. Oddly, the processor specs say that it does not come with a fan.
In general, are processor fans a standard size, and will most fans fit most…
MirroredFate
- 467
- 5
- 8
-1
votes
6 answers
Experience of replacing fans in Dell Poweredge 1850
I've recently aquired a Dell Poweredge 1850 (1U rackmount server). Spec wise, it's great for what I need it for (running VMWare with a few VMs, pfSense firewall etc). The problem is it's not going to sit in a server room / data centre and the fans…
Chris Pont
- 119
- 1
- 6
-1
votes
0 answers
Fan management dell t5500
I have a dell T5500 than i run with linux mint 20.3.
Recently one the fan start to have that issue that it starts to go full speed all the time.
When running the command sensors to check on the temperature in the case, i can see the…
Vincent
- 1
-2
votes
2 answers
HP ProLiant DL380e Gen8 has high fan speed after installing second CPU
Today I installed a second CPU in our HP ProLiant DL380e Gen8, and after booting the fans all went to 99.96%. This causes the server to make an enormous amount of noise.
Could it damage the server? What could I do to fix this?
I already removed all…
Maarten Ureel
- 239
- 2
- 5
- 12
-2
votes
1 answer
Replacing a loud fan in a 1RU server
I just bought a firewall that is very loud. The biggest problem is the two fans in the back (2 x Sunon 40mm fans) running at full speed.
The firewall is 1RU with pfSense installed on it.The CPU is a Pentium 4 2.8 GHZ with a heat sink on top.
The air…
Jojje
- 17
- 2