7

How can I determine which /dev/sdX device my usb stick is plugged into?

I am running Ubuntu 9.04.

jldupont
  • 1,779
  • 4
  • 23
  • 27

4 Answers4

10

You may want to use /dev/disk/by-id or /dev/disk/by-uuid/ instead. These never change for a given device, whatever /dev/sdXX your pluggable drives have.

wazoox
  • 6,782
  • 4
  • 30
  • 62
9

Execute sudo blkid : it will show block device names:

/dev/sdc1: UUID="004A31DB4A31CDE2" LABEL="WinGamer" TYPE="ntfs"
/dev/sdd1: LABEL="0DAY" UUID="9b14c03b-7251-434f-bbb9-eac42b2db927" TYPE="ext2"
/dev/sdg5: LABEL="QFAT" UUID="4257-E346" TYPE="vfat"
/dev/sdg6: LABEL="BACKUP-HDD" UUID="fee45c66-11bd-49fa-a62a-4a541716e8e1" TYPE="ext2"
kolypto
  • 10,738
  • 12
  • 51
  • 66
3

on a command line, do a ls /media and you will usually see it.

e.g. on my system:

$ ls /media
cdrom  cdrom0  cdrom1  floppy  floppy0  LaCie

LaCie is my usb stick

failing that try

$ lsusb

on my system

$ lsusb
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
...
Bus 001 Device 004: ID 059f:1028 LaCie, Ltd 
...

If it shows up there but not in /media, you will need to figure out mounting, or ask another question..

Finally, I can type "mount" and look through the output for your answer, or in my case:

$ mount | grep LaCie
/dev/sdb on /media/LaCie type vfat (rw,nosuid,nodev,uhelper=hal,shortname=mixed,uid=1000,utf8,umask=077,flush)
Dennis Williamson
  • 60,515
  • 14
  • 113
  • 148
2

It will depend. Type dmesg at the console and the output should show the USB stick being mounted.

Here is some example output:

[ 2699.328853] Initializing USB Mass Storage driver...
[ 2699.339045] scsi4 : SCSI emulation for USB Mass Storage devices
[ 2699.345916] usbcore: registered new interface driver usb-storage
[ 2699.345922] USB Mass Storage support registered.
[ 2699.350764] usb-storage: device found at 3
[ 2699.350767] usb-storage: waiting for device to settle before scanning
[ 2704.353322] usb-storage: device scan complete
[ 2704.354353] scsi 4:0:0:0: Direct-Access     USB      DISK 2.0         0403 PQ: 0 ANSI: 0 CCS
[ 2704.374592] sd 4:0:0:0: [sdb] 3981312 512-byte hardware sectors: (2.03 GB/1.89 GiB)
[ 2704.415233] sd 4:0:0:0: [sdb] Write Protect is off
[ 2704.415239] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 2704.415242] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 2704.418087] sd 4:0:0:0: [sdb] 3981312 512-byte hardware sectors: (2.03 GB/1.89 GiB)
[ 2704.419100] sd 4:0:0:0: [sdb] Write Protect is off
[ 2704.419105] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 2704.419107] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 2704.419114]  sdb: sdb1
[ 2704.421024] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 2704.421093] sd 4:0:0:0: Attached scsi generic sg2 type 0

In my case its the sdb device that is assigned after I plug in a USB stick, since I have just the one internal hard drive in my laptop (sda).

faultyserver
  • 1,904
  • 1
  • 16
  • 20
  • Thanks! I saw the dmesg message "sdc: sdc1" which I hope is the correct path ;-) – jldupont Oct 23 '09 at 16:12
  • This works, but is the ghetto way to do it. The other answers are better, IMO – Kamil Kisiel Oct 23 '09 at 17:09
  • @Kamil - Your right, this IS the ghetto way to do it but its also the easiest/simplest, especially for a newcomer. If you need to script up a solution then several of the other answers would do nicely, I would imagine :-) – faultyserver Oct 23 '09 at 21:19