OnePlus 9 5G Screen Replacement

Written By: Dominik Schnabelrauch

Comments: 1

Difficulty

Moderate

Steps

Time Required

1 - 2 hours

Introduction

Use this guide to replace the screen on your OnePlus 9 5G.

You'll need replacement adhesive for the rear glass and the screen in order to complete this repair.

Note: Retaining water resistance after the repair depends on how clean the mating surfaces are and how accurately the adhesive is reapplied. Your device will lose its factory-given IP (Ingress Protection) rating, however, only the T-Mobile versions of the OnePlus 9 5G offer an IP rating.

Tools

Parts

Step 1

Insert a SIM eject tool, bit, or straightened paper clip into the SIM card tray hole on the bottom edge of the phone.
Press firmly to eject the tray.

Step 2

Remove the SIM card tray from the phone.
When reinserting the SIM card, make sure it's in the proper orientation inside the tray.
A thin rubber gasket around the SIM tray provides water and dust protection. If this gasket is damaged or missing, replace the gasket or the entire SIM tray to protect your phone's internal components.

Step 3

Completely power off your phone before you begin.
Prepare an iOpener and apply it to the rear glass for at least three minutes to loosen the adhesive underneath.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

Step 4

Apply a suction handle to the rear glass, as close to the bottom edge as possible.
If your rear glass is badly cracked, covering it with a layer of clear packing tape may allow the suction handle to adhere. Alternatively, very strong tape may be used instead of the suction handle. If all else fails, you can superglue the suction handle to the broken rear glass.
Pull up on the suction handle with strong, steady force to create a gap between the glass and the frame.
If you have trouble creating a gap, apply more heat to further soften the adhesive.
Insert an opening pick into the gap.

Step 5

Slide the opening pick to the bottom right corner to slice the adhesive.
Leave the opening pick in place to prevent the adhesive from resealing.

Step 6

Insert a second opening pick underneath the bottom edge of the rear glass.
Slide the opening pick to the bottom left corner to slice the adhesive.
Leave the opening picks in place to prevent the adhesive from resealing.

Step 7

If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.
Insert a third opening pick underneath the bottom left corner of the rear glass.
Slide the opening pick along the left edge of your phone to slice the adhesive.
Leave the opening pick in the top left corner to prevent the adhesive from resealing.

Step 8

Insert a fourth opening pick underneath the top left corner of the rear glass.
Slide the opening pick along the top edge to slice the adhesive.
Leave the opening pick in the top right corner to prevent the adhesive from resealing.

Step 9

Insert a fifth and final opening pick underneath the top right corner of the rear glass.
Slide the opening pick along the right edge of the back cover to slice the remaining adhesive.

Step 10

Remove the rear glass.
If the rear glass is still stuck to the frame, slide an opening pick around the entire perimeter until the rear glass separates completely.
During reassembly secure the rear glass with pre-cut adhesive or double-sided adhesive tape. After installing the rear glass, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.

Step 11

Use a pair of tweezers to carefully peel the bottom right corner of the charging coil tape off of the daughterboard cover.

Step 12

Use a pair of tweezers to carefully peel the bottom left corner of the charging coil tape off of the loudspeaker.

Step 13

The flash assembly is held in place by mild adhesive and covers a motherboard cover screw.
Carefully slide an opening pick underneath the bottom edge of the flash assembly.
Use your opening pick to pry up the flash assembly.
Don't try to remove the flash assembly all the way during this procedure. Its cable is adhered to the backside of the motherboard cover.

Step 14

Use a Phillips screwdriver to remove the ten 3.8 mm-long screws securing the motherboard cover.
One of the motherboard cover screws is covered by a white water ingress sticker. To unfasten the screw you can puncture the sticker with your screwdriver.

Step 15

The motherboard cover is further held in place by tight plastic clips.
Insert a spudger underneath the bottom right edge of the motherboard cover.
Pry upwards to loosen the motherboard cover and create a gap.

Step 16

Insert an opening pick underneath the bottom right edge of the motherboard cover.
Slide the opening pick up along the right edge of the motherboard cover.
Twist the opening pick to release the plastic clips and pry up the motherboard cover.

Step 17

Use a pair of tweezers or your fingers to remove the motherboard cover.
The charging coil is attached to the motherboard cover and will lift up at the same time.

Step 18

Use a spudger to disconnect the battery cable by prying the connector straight up from its socket on the bottom left corner of the motherboard.
To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend and cause permanent damage.

Step 19

Use a Phillips screwdriver to remove the five 3.8 mm-long screws securing the daugtherboard cover.
One of the daughterboard cover screws is covered by a white water ingress sticker. To unfasten the screw you can puncture the sticker with your screwdriver.

Step 20

Insert the point of a spudger underneath the top right edge of the daughterboard cover.
Pry upwards to loosen the daughterboard cover.

Step 21

Use a pair of tweezers or your fingers to remove the daughterboard cover.

Step 22

Use a spudger to disconnect the interconnect cable from the motherboard by prying the connector straight up from its socket.

Step 23

Slide one arm of a pair of tweezers underneath the metal bracket covering the interconnect cable.
Use your tweezers to lift and unhinge the metal bracket.
Remove the metal bracket.

Step 24

Use a spudger to disconnect the interconnect cable from the daughterboard by prying the connector straight up from its socket.

Step 25

Use a pair of tweezers or your fingers to remove the interconnect cable.

Step 26

Use a spudger to disconnect the antenna board cable and the fingerprints sensor from the daughterboard by prying the connectors straight up from their sockets.

Step 27

Slide one arm of a pair of tweezers under the black antenna cable until it‘s snug against the metal connector.
Disconnect the antenna cable by prying the connector straight up from the daughterboard.

Step 28

Slide one arm of a pair of tweezers under the white antenna cable until it‘s snug against the metal connector.
Disconnect the antenna cable by prying the connector straight up from the daughterboard.

Step 29

Use a Phillips driver to remove the 2.8 mm-long screw securing the daughterboard.

Step 30

Insert the point of a spudger underneath the top right corner of the daughterboard.
Pry upwards to loosen the daughterboard.

Step 31

Use a pair of blunt nose tweezers or your fingers to remove the daughterboard.
Before reinserting the daughterboard, make sure all cables that connect to it are out of the way.

Step 32

Use a spudger to disconnect the display cable by prying the connector straight up from its socket on the bottom right corner.

Step 33

Apply a heated iOpener to the screen for 3 minutes to loosen the adhesive underneath.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the device. The edge should feel slightly too hot to touch.

Step 34

Apply a suction handle to the bottom edge of the screen.
If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.
Pull up on the suction handle with strong, steady force and insert an iFlex between the screen and frame.
Make sure to insert the iFlex underneath the screen and not the plastic frame.
Depending on the age of your phone, this may be difficult. If you're having trouble, apply more heat to the bottom edge and try again.

Step 35

Insert an opening pick between the iFlex and the screen.
Remove the iFlex.

Step 36

Slide the opening pick to the bottom right corner of the screen to slice its adhesive.
Leave the opening pick in place to prevent the adhesive from resealing.

Step 37

Insert a second opening pick at the bottom right corner and slide it to the bottom left corner of the screen to slice the adhesive.
Leave the opening pick in place to prevent the adhesive from resealing.

Step 38

Insert a third opening pick underneath the bottom left corner of the screen.
Slide the opening pick along the left edge of the screen to slice the adhesive.
When slicing near the front facing camera, only insert the opening pick 2.5 mm to avoid damaging it.
Leave the opening pick in the top left corner to prevent the adhesive from resealing.

Step 39

If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener or heat gun for 1–2 minutes to reheat it.
Insert a fourth opening pick at the top left corner of the screen.
Slide the opening pick along the top edge of the phone to slice the adhesive.
Leave the opening pick in the top right corner to prevent the adhesive from resealing.

Step 40

Insert a fifth opening pick underneath the top right corner of the screen and slide it along the right edge of the phone to slice the remaining adhesive.
Don't try to remove the display all the way yet, the display cable is still threaded through the midframe.

Step 41

Flip the phone over.
Lift the bottom edge of the phone and carefully thread the display cable through its gap in the frame.

Step 42

Remove the screen.
During reassembly, follow this guide to install custom-cut adhesives for your device.

Very well written guide, with plenty of photos to show the way. Very nicely done!!

Jeff -

Conclusion

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before you install it.

To reassemble your device, follow these instructions in reverse order.

During reassembly, apply new adhesive where it's necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our OnePlus 9 5G answers community for help.

Author

Dominik Schnabelrauch

Member since: 23/11/16

201162 Reputation

OnePlus 9 5G Screen Replacement

Introduction

Tools

Parts

0 comments