Nintendo Switch Lite Battery Disconnection

Step 1

Before beginning this repair, make sure that the device is completely turned off.
Use a Y00 screwdriver to remove the four 6.3 mm-long screws securing the back panel.
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

All my screws got stripped any ideas on how to remove?

Almost A Mammal -

A Y0 screwdriver seemed to work better for me.

Tommy Morrill -

What type of screw driver do I use to un screw the screws and which way

Luca Capito -

Y 0.6 was all I had but it seemed to fit perfectly

Trevor -

Step 2

Use a JIS 000 driver or an official iFixit PH 000 driver to remove the following screws securing the back panel:
Two 3.6 mm-long screws on the top of the device
Two 3.6 mm-long screws on the bottom of the device
To prevent these tight screws from stripping, apply firm downward force, work slowly and try a different screwdriver if the screws won't come out.

I accidentally stripped the back screw and now I can't open it. I removed all the other screws. What should I do?

tiggytiger555 -

Step 3

Insert an opening tool into the left speaker grille on the bottom of the device.
Twist the opening tool to release the clips securing the back panel.
Avoid inserting the opening tool further than required to prevent damage to the speaker module.

Step 4

Slide the opening tool around the bottom-left corner to release the clips on the left side of the device.

Step 5

Insert an opening tool into the right speaker grille on the bottom of the device.
Twist the opening tool to release the clips.
Avoid inserting the opening tool further than required to prevent damage to the speaker module.

Step 6

Slide and pry the opening tool around the bottom-right corner to release the clips on the right side of the device.

Step 7

Continue sliding and prying the opening tool along the gap on the top of the device to release the clips.

Step 8

Lift the bottom edge of the back panel, opening it like a book.
Remove the back panel.

Step 9

Use a JIS 000 driver or an official iFixit PH 000 driver to remove the following four screws:
Three 3.1 mm screws
One 4.5 mm screw

There are four screws instead of three mentioned

Khurram Chaudry -

it doesnt mention 3 anywhere, and it labels all four

Ezi -

With how easy it seems to be to do serious damage with the next few steps, I figured I'd say that realistically you can skip steps 9-13 when doing this repair. While they provide a bit of extra security by disconnecting the battery, the left stick is completely accessible and replaceable without touching the heat shield or anything underneath (And steps 17 and 18 disconnect power from the daughter board regardless).

Nate -

i stripped a &&^&^$^ screw

SpongebobFan254 -

Well I actually removed the screw right next to the 4.5 screw. I did not realize it till my son showed me why the plate wouldn't release. Ha ha, it's funny now but yeah not a big deal. I could have bent it badly assuming I took all screws out though. For anyone reading this before going in. 👍

Toastninja -

Step 10

Use a spudger or your fingers to lift the shield plate up and out of the device.
You may feel a bit of resistance. This is normal, since the shield plate is slightly bonded to the heat sink with thermal paste.
Remove the shield plate.
Clean off the old thermal paste from the shield plate and heat sink using isopropyl alcohol and a microfiber cloth. Apply new thermal paste to the heat sink before reassembly.

You may need to replace the thermal paste on the heat sink.

ahoz28 -

Step 11

Use an opening tool or your fingernail to flip up the small, hinged locking flap on the motherboard interconnect cable's ZIF connector.

The clip broke off when trying to remove this cable. Audio only works through headphones and the display now won’t turn on after the clip broke. Does anyone know where I could get a clip or how I could fix it without it?

Alexz Zepeda -

Mi è successa la stessa cosa è non so come ripararla! Chissà se c’è un modo!

Paolo De Falco -

Step 12

Do Not Use Metal Tweezers! Some fixers state that metallic tweezers can short circuit the ribbon cable/connector. It might be safer to just use nylon-tipped or ceramic-tipped tweezers.
Use a pair of tweezers to slide the interconnect cable out of its connector on the motherboard.

I turned the unit off beforehand, I used tweezers just like the instructions said (ifixit branded) , my device sparked and now it won’t turn back on

User Service -

The flap came off is it important or is there a way t fix it?

Jose Cruz R Rangel Cordero -

We're you able to get it working without the white flap? My screen is not working after putting it back together and i noticed this white flap was falling off

Jimmy “Ghost” Trost -

Did you get it working without the white flap? Everything on the switch works fine except for audio going through headphones and the display not turning on.

Alexz Zepeda -

do not use metal sharp pointed tweezers! you will rip your ribbon cable. Use the inside of a Bic type pen or something else dull and plastic to pull the cable away by putting the pen part where the first bend is.

Christopher Bales (C.J.) -

Anyone figure out how to fix this? my device shorted in this step.

Acord -

Step 13

Use the point of a spudger to pry the battery connector straight up and out of its socket on the motherboard.

Caution the connector may not be properly soldered onto the motherboard. For me it snapped off the pins and now have to find a place to get that fixed if even possible. may have bricked it.

Craig Osman - 30/01/21

Yup, broke the connector right off the motherboard. Thanks, ifixit -_-

Justin Kerr - 14/04/21

I backed out when I reached this point. I couldn't risk damaging it. Do u just need to pull it up? Did you mean that it might have been soldered shut below?

Jannalyzer -

You should just need to pull straight up, but make sure you’re pulling on the wires or the gray plug—do not pull on the black socket or it can snap off of the motherboard.

Adam O'Camb -

I pulled straight up from the south side on under 2 or three wires and held down the device as I pulled and the gray connector disconnected from the black connector on the Switch. Just be careful at this part.

Jon -

With how easy it seems to be to do serious damage at this point, I figured I'd say that realistically you can skip steps 9-13 when doing this repair. While they provide a bit of extra security by disconnecting the battery, the left stick is completely accessible and replaceable without touching the heat shield or anything underneath (And steps 17 and 18 disconnect power from the daughter board regardless).

Nate -

just broke my connector... ifixit PLEASE put a warning on how fragile the solder on this connector is.

Nate Mascis -

Note for this step, you do not need to apply a lot of force. I used two tools here: small screwdriver to hold down the black base, and one side of fine-tipped tweezers to get under all 3 wires. Gently, push down on the tweezers to push the wires upwards, which should force the gray connector up and off the base. It did not take a lot of force. Take your time and it will be fine. Again, like others have said, do NOT pull or pry up the black base.

Christopher Gillett - 23/09/23