MacBook Air 13" Late 2020 Antenna Bar Replacement

Written By: Carsten Frauenheim
  • Comments: 33
MacBook Air 13" Late 2020 Antenna Bar Replacement

Difficulty

Moderate

Steps

12

Time Required

10 - 30 minutes

Introduction

Use this guide to remove or replace the antenna bar in a Late 2020 MacBook Air (M1).

  1. VPEGroiLj2rq1TsX

    • Before starting this procedure, you should disable your Mac's Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide to disable Auto Boot.

    • If your MacBook is running Big Sur v11.1 or later, disabling Auto Boot may not work. You can proceed normally, but make sure to disconnect the battery as soon as you're inside.

    • Completely power off and unplug your MacBook before you start. Close the display and flip the entire laptop upside-down.

    • Use a P5 driver to remove the following screws:

    • Two 7.9 mm screws

    • Two 7.3 mm screws

    • Six 2.6 mm screws

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your MacBook.

    ESD safe mat, plugged into ground, with a wrist strap, also grounded, are the best best to protect the logic board.

    Robin Ray -

    Re-Assembly Tip: Before putting the screws back in, snap the lower case on and test to make sure the MacBook powers up. When I first re-assembled, I became very nervous I did something wrong because it would not power on. It turns out I just needed to plug the laptop into a power source for it to power up (despite having a good charge before disassembly). It was the perfect way to test the new USB-C ports!

    Austin -

    Big points to this one, especially for mentioning needing to plug the laptop in. The bottom case needs to be screwed in and laptop needs to be plugged in before it will boot.

    Bayden Yazalina -

    Wiha 4PL driver for these screws.

    Greg Worrel -

    Printing out all the images from this Ifixit guide prior to starting and using duct tape help me keep track of screws.

    raju midjdeya -

  2. JM2r2fTloLj1HGHv
    JM2r2fTloLj1HGHv
    qWKL1OR1c1CmZJKh
    qfGXhnWu5SInbUHj

    • Wedge your fingers between the display and the lower case and pull upward to pop off the lower case.

    • Remove the lower case.

    • To reinstall the lower case:

    • Set it in place and press firmly to engage the two hidden clips underneath. You should feel and hear them snap into place.

    Los tornillos se ruedan fácilmente :(

    Mishelle Cerón -

  3. NWhygZ3NuFfSLrCC
    NWhygZ3NuFfSLrCC
    kRYFRljHKcJHQMni
    VevmEYadgKPXgXRH

    • Use the flat end of a spudger to pry up and unlatch the metal locking arm on the battery connector.

    • Make sure the metal arm is completely free of the locking tab before lifting the battery connector. The metal locking arm should easily unlatch.

    • Lift straight up on the metal locking arm to pull the battery connector out of its socket on the logic board.

    • During reassembly, press the battery connector straight down into its socket, making sure it sits flush within the socket.

    • If necessary, push the rear, wire side of the connector into place first, then rock the front of the connector into place.

    Reassembly: I had difficulty going straight down. The connector has some angled edges that made it difficult. Instead, I slotted the wire side in first, then rocked it forward towards the hinge into position.

    Sean K -

    If having difficulty in flipping the bar up, place the machine vertical and not that there is a small “locking nib” that the bar has to clear. You may have to give the bar honest persuasion to clear the nib.

    Harry Dulcamara -

  4. pMA6bFPjPuCcCuXw

    • Use a T3 Torx driver to remove the 1.4 mm screw securing the antenna cable cover.

    • If your T3 bit feels a bit too loose, you may need to use a T4.

    I needed a T4 for this

    MaFt Morley -

    Wiha tools T3 fit perfectly.

    Robin Ray -

    I found this screw difficult to reinstall. Very small and fiddly. 15-20 minutes on this step.

    Harry Dulcamara -

    The T3/T4 screws are tiny!!!

    raju midjdeya -

    To reinstall a tiny screw first turn it counterclockwise until you feel it engage the tread, then turn them clockwise to tighten it.

    Patrick Langvardt -

  5. DolxfCVyMJbuVaYK

    • Remove the antenna cable cover.

    Make sure the 90 degree bend on the cover is towards the hinge when reassembling. It will fit in backwards, but will cause problems.

    Robin Ray -

  6. YjXHvrYawVQGdCsF
    YjXHvrYawVQGdCsF
    ghAw1ida5JywpKYy
    Gei2HaBBD4QLOChH

    • Use a pair of tweezers to grip the antenna connector close to its base.

    • Pull straight up to disconnect the cable.

    • Repeat for the second antenna cable.

    • During reassembly, hold the connectors in place and gently press them straight down. The connectors “snap” into their sockets.

    These are tiny, and hard to reconnect. The key was to position the cables so their ends are very close to the posts on the board.

    dexter -

    Yep. Good call. Me too folks.

    Harry Dulcamara -

    So anyone that’s had experience with keyboard and antenna, connectors, or previous Apple iPhone products, knows that these antenna connectors go on from front to back so you kind of have to position the noncable end of the antenna cable first and then push it towards the back I’m not sure if that makes sense, but try from the front to the back connecting Put pressure on the front first and then put pressure towards the cable in if you do it wrong and put too much pressure in it, you can ruin the cables. Be careful with it.

    babs martin -

  7. 1VJvIwAxTOJogU5w

    • Use a T3 Torx driver to remove the two 1.5 mm screws securing the display cable connector cover.

    None of the screws in this repair are T3. All the smaller ones are T4. Which is good, ‘cause my (cheap) repair tool kit doesn’t have a T3.

    dexter -

    The T3 screws called out were indeed T3, not T4 on the MacBook Air I replaced the display on.

    --Mac Ace, Inc.

    Robin Ray -

    I dropped one of these - can they be purchased? Or is there a matching screw in an older MacBook Air? I have a ton of those for parts... :-)

    Jimmy Anderson -

    weird, for my model A2337 it is even T2 screws. tested it two times and I have the ifixit mako precision bit set.

    Otto Klassen -

    On my MacBook Air M1 Early 2020, I had to use a T4 bit on one of the screws. The other one came out with a T3. I am using a HyperTough 77-piece precision repair set.

    Raj Venkat -

  8. 4LyTebwNMFNoFqJf

    • Remove the display cable connector cover.

  9. yGHHGP6i2yHfUM4N
    yGHHGP6i2yHfUM4N
    NCZ4EGyX5OgOcx4R

    • Use the flat end of a spudger to pry the display cable connector straight off of the antenna board to disconnect it.

    • To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

    Since this step is the most crucial in the reassembly process I suggest connecting the flat cable to the board BEFORE placing the board in to its cavity in the antenna bar. MUCH easier and SAFER to do.

    J Patrick Dowling -

  10. 2b1wYIiFCJDuN2s5

    • Use a T5 Torx driver to remove the six screws securing the antenna bar:

    • Four 7.4 mm silver screws

    • Two 4.7 mm black screws

    Mine here is T6 Torx not T5.

    David Jones -

    When putting it back together, make sure to get the display cable connector out from under the antenna board before screwing the antenna bar back down. The connector has to go behind the bar in the little notch as the board goes through the opening in the bar.

    Matthew Granger -

    Mine here were Torx T4. Came with the kit.

    Jace Sheppard -

    My 4.7 mm screw is stripped.

    Any suggestions to get it removed?

    B S -

    B S,

    Darn, sorry that happened! Here's a guide with five different methods you can try to get it loose: How to Remove a Stripped Screw

    Best of luck!

    Carsten Frauenheim -

    These are T5. A T4 might work but you might strip it.

    A T6 shouldn't fit at all; if it does, your driver is either worn or just poor quality.

    maccentric -

  11. SAEGGdfncZdeZYYm
    SAEGGdfncZdeZYYm
    BAsqqhw4iQ4CWtpH
    qeEvDZBflVmW4Nlw

    • Insert the pointed end of a spudger into the gap between the antenna bar and display hinge.

    • Pivot the spudger against the hinge to pry up the end of the antenna bar.

    • Repeat for the other end of the antenna bar.

  12. Iokx4fkJ45pYlhlf
    Iokx4fkJ45pYlhlf
    TFAUPiYpoxIFaihc
    AanhCNNBiMLVkvFG

    • Use your fingers to pry the antenna bar straight up and away from the case.

    • The antenna bar is secured with some adhesive and may require some force to dislodge.

    • Thread the antenna board through the opening in the middle of the antenna bar.

    • Be careful to not put any strain on the antenna bar's ribbon cables.

    • Remove the antenna bar.

    Separating antennae bar from case after removing screws is challenging. Author’s directions are good but what needs to be addressed is a thin strip of adhesive on both sides of the bar that needs to be separated. the strips are located on the hinge edge of the logic board mount area. I used a metal, razor thin, wide, blade type spudger to gently “wedge” underneath the bar along both adhesive strips to loosen the bar and lift it up. Careful!

    Macrepair SF -

    Thanks for this hint!!

    Benjamin Bradshaw -

    Before removing the antenna bar see if the right side is slightly elevated than the left. Upon replacement I could not get the right side to sit as flush as the left. However it may be intentional to protect the wifi wires.

    Harry Dulcamara -

    I was stuck on this step (removing the antenna bar) but this video helped me: https://www.youtube.com/watch?v=tHhHNjzO...

    Matthias -

Conclusion

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Once you've completed your repair, your laptop may not power back on until connected to power.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Author

Carsten Frauenheim

Member since: 10/03/20

110978 Reputation

0 comments