rp-process

The rp-process (rapid proton capture process) consists of consecutive proton captures onto seed nuclei to produce heavier elements.[1] It is a nucleosynthesis process and, along with the s-process and the r-process, may be responsible for the generation of many of the heavy elements present in the universe. However, it is notably different from the other processes mentioned in that it occurs on the proton-rich side of stability as opposed to on the neutron-rich side of stability. The end point of the rp-process (the highest-mass element it can create) is not yet well established, but recent research has indicated that in neutron stars it cannot progress beyond tellurium.[2] The rp-process is inhibited by alpha decay, which puts an upper limit on the end point at ¹⁰⁴Te, the lightest observed alpha-decaying nuclide,[3] and the proton drip line in light antimony isotopes. At this point, further proton captures result in prompt proton emission or alpha emission, and thus the proton flux is consumed without yielding heavier elements; this end process is known as the tin–antimony–tellurium cycle.[4]

Nucleosynthesis of proton-rich nuclei by rapid proton capture

Conditions

The process has to occur in very high-temperature environments (above 10⁹ kelvins) so that the protons can overcome the large Coulomb barrier for charged-particle reactions. A hydrogen-rich environment is also a prerequisite due to the large proton flux needed. The seed nuclei needed for this process to occur are thought to be formed during breakout reactions from the hot CNO cycle. Typically proton capture in the rp-process will compete with (α,p) reactions, as most environments with a high flux of hydrogen are also rich in helium. The time scale for the rp-process is set by β⁺ decays at or near the proton drip line, because the weak interaction is notoriously slower than the strong interaction and electromagnetic force at these high temperatures.

Possible sites

Sites suggested for the rp-process are accreting binary systems where one star is a neutron star. In these systems the donor star is accreting material onto its compact partner star. The accreted material is usually rich in hydrogen and helium because of its origin from the surface layers of the donor star. Because such compact stars have high gravitational fields, the material falls with a high velocity towards the compact star, usually colliding with other accreted material en route, forming an accretion disk. In the case of accretion onto a neutron star, as this material slowly builds up on the surface, it will have a high temperature, typically around 10⁸ K. Eventually, it is believed that thermonuclear instabilities arise in this hot atmosphere, allowing the temperature to continue to rise until it leads to a runaway thermonuclear explosion of the hydrogen and helium. During the flash, the temperature quickly rises, becoming high enough for the rp-process to occur. While the initial flash of hydrogen and helium lasts only a second, the rp-process typically takes up to 100 seconds. Therefore, the rp-process is observed as the tail of the resulting X-ray burst.

See also

• p-nuclei

References

1. Lars Bildsten, "Thermonuclear Burning on Rapidly Accreting Neutron Stars" in The Many Faces of Neutron Stars, ed. R. Buccheri, J. van Paradijs, & M. A. Alpar (Kluwer), 419 (1998).
2. Schatz, H.; A. Aprahamian; V. Barnard; L. Bildsten; A. Cumming; et al. (April 2001). "End Point of the rp Process on Accreting Neutron Stars". Physical Review Letters. 86 (16): 3471–3474. arXiv:astro-ph/0102418. Bibcode:2001PhRvL..86.3471S. doi:10.1103/PhysRevLett.86.3471. PMID 11328001. Retrieved 2006-08-24.
3. Auranen, K.; et al. (2018). "Superallowed α decay to doubly magic ¹⁰⁰Sn" (PDF). Physical Review Letters. 121 (18): 182501. doi:10.1103/PhysRevLett.121.182501. PMID 30444390.
4. Lahiri, S.; Gangopadhyay, G. (2012). "Endpoint of rp process using relativistic mean field approach and a new mass formula". International Journal of Modern Physics E. 21 (8). arXiv:1207.2924. doi:10.1142/S0218301312500747.