Fresnel zone

A Fresnel zone (/freɪˈnɛl/ fray-NEL), named after physicist Augustin-Jean Fresnel, is one of a series of confocal prolate ellipsoidal regions of space between and around a transmitter and a receiver. Transmitted radio, sound, or light waves can follow slightly different paths before reaching a receiver, especially if there are obstructions or reflecting objects between the two. The waves can arrive at slightly different times and will be slightly out of phase due to the different path lengths. Depending on the magnitude of the phase shift, the waves can interfere constructively or destructively. The size of the calculated Fresnel zone at any particular distance from the transmitter and receiver can help to predict whether obstructions or discontinuities along the path will cause significant interference.

Fresnel zone: D is the distance between the transmitter and the receiver; r is the radius of the first Fresnel zone (n=1) at point P. P is d1 away from the transmitter, and d2 away from the receiver.

Significance

In any wave-propagated transmission between a transmitter and receiver, some amount of the radiated wave propagates off-axis (not on the line-of-sight path between transmitter and receiver). This can then deflect off of objects and then radiate to the receiver. However, the direct-path wave and the deflected-path wave may arrive out of phase, leading to destructive interference when the phase difference is a half-integer multiple of the period. The n-th Fresnel zone is defined as the locus of points in 3D space such that a 2-segment path from the transmitter to the receiver that deflects off a point on that surface will be between n-1 and n half-wavelengths out of phase with the straight-line path. The boundaries of these zones will be ellipsoids with foci at the transmitter and receiver. In order to ensure limited interference, such transmission paths are designed with a certain clearance distance determined by a Fresnel-zone analysis.

The dependence on the interference on clearance is the cause of the picket-fencing effect when either the radio transmitter or receiver is moving, and the high and low signal strength zones are above and below the receiver's cut-off threshold. The extreme variations of signal strength at the receiver can cause interruptions in the communications link, or even prevent a signal from being received at all.

Fresnel zones are seen in optics, radio communications, electrodynamics, seismology, acoustics, gravitational radiation, and other situations involving the radiation of waves and multipath propagation. Fresnel zone computations are used to anticipate obstacle clearances required when designing highly directive systems such as microwave parabolic antenna systems. Although intuitively, line-of-sight between transmitter and receiver seems to be all that is required for a strong antenna system, because of the complex nature of radio waves, obstructions within the first Fresnel zone can cause significant weakness, even if those obstructions are not blocking the line-of-sight signal path. For this reason, it is valuable to do a calculation of the size of the 1st, or primary, Fresnel zone for a given antenna system. Doing this will enable the antenna installer to decide if an obstacle, such as a tree, is going to make a significant impact on signal strength. The rule of thumb is that the primary Fresnel zone would ideally be 80% clear of obstacles, but must be at least 60% clear.

Spatial structure

First Fresnel zone avoidance

Fresnel zones are confocal prolate ellipsoidal shaped regions in space (e.g. 1, 2, 3), centered around the line of the direct transmission path (path AB on the diagram). The first region includes the ellipsoidal space which the direct line-of-sight signal passes through. If a stray component of the transmitted signal bounces off an object within this region and then arrives at the receiving antenna, the phase shift will be something less than a quarter-length wave, or less than a 90º shift (path ACB on the diagram). The effect regarding phase-shift alone will be minimal. Therefore, this bounced signal can potentially result in having a positive impact on the receiver, as it is receiving a stronger signal than it would have without the deflection, and the additional signal will potentially be mostly in-phase. However, the positive attributes of this deflection also depends on the polarization of the signal relative to the object (see the section on polarization below).

The 2nd region surrounds the 1st region but excludes the first region. If a reflective object is located in the 2nd region, the stray sine-wave which has bounced from this object and has been captured by the receiver will be shifted more than 90º but less than 270º because of the increased path length, and will potentially be received out-of-phase. Generally this is unfavorable. But again, this depends on polarization (explained below).

The 3rd region surrounds the 2nd region and deflected waves captured by the receiver will have the same effect as a wave in the 1st region. That is, the sine wave will have shifted more than 270º but less than 450º (ideally it would be a 360º shift) and will therefore arrive at the receiver with the same shift as a signal might arrive from the 1st region. A wave deflected from this region has the potential to be shifted precisely one wavelength so that it is exactly in sync with the line-of-sight wave when it arrives at the receiving antenna.

The 4th region surrounds the 3rd region and is similar to the 2nd region. And so on.

If unobstructed and in a perfect environment, radio waves will travel in a relatively straight line from the transmitter to the receiver. But if there are reflective surfaces that interact with a stray transmitted wave, such as bodies of water, smooth terrain, roof tops, sides of buildings, etc., the radio waves deflecting off those surfaces may arrive either out-of-phase or in-phase with the signals that travel directly to the receiver. Sometimes this results in the counter-intuitive finding that reducing the height of an antenna increases the signal-to-noise ratio at the receiver.

Although radio waves generally travel in a straight line, fog and even humidity can cause some of the signal in certain frequencies to scatter or bend before reaching the receiver. This means that objects that are clear of the line of sight path will still potentially block parts of the signal. To maximize signal strength, one needs to minimize the effect of obstruction loss by removing obstacles from both the direct radio frequency line of sight (RF LoS) line and also the area around it within the primary Fresnel zone. The strongest signals are on the direct line between transmitter and receiver and always lie in the first Fresnel zone.

In the early 19th century, French scientist Augustin-Jean Fresnel discovered a method to calculate where the zones are — that is, whether a given obstacle will cause mostly in-phase or mostly out-of-phase deflections between the transmitter and the receiver.

Clearance

Several examples of how Fresnel zones can be disrupted

The concept of Fresnel zone clearance may be used to analyze interference by obstacles near the path of a radio beam. The first zone must be kept largely free from obstructions to avoid interfering with the radio reception. However, some obstruction of the Fresnel zones can often be tolerated. As a rule of thumb the maximum obstruction allowable is 40%, but the recommended obstruction is 20% or less.[1]

For establishing Fresnel zones, first determine the RF line of sight (RF LoS), which in simple terms is a straight line between the transmitting and receiving antennas. Now the zone surrounding the RF LoS is said to be the Fresnel zone.[2] The cross sectional radius of each Fresnel zone is the longest at the midpoint of the RF LoS, shrinking to a point at each vertex (which coincide with the antenna on each end, within the approximation made).

Formulation

Consider an arbitrary point P in the LoS, at a distance $d_{1}$ and $d_{2}$ with respect to each of the two antennas. To obtain the radius $r_{n}$ of zone $n$ , note that the volume of the zone is delimited by all points for which the difference in distances, between the direct wave ( $D=d_{1}+d_{2}$ ) and the reflected wave ( ${\overline {AP}}+{\overline {PB}}$ ) is the constant $n{\frac {\lambda }{2}}$ (multiples of half a wavelength). This effectively defines an ellipsoid with the major axis along ${\overline {AB}}$ and foci at the antennas (points A and B). So:

{\overline {AP}}+{\overline {PB}}-D=n{\frac {\lambda }{2}}

Re-writing the expression with the coordinates of point $P$ and the distance between antennas $D$ , it gives:

{\sqrt {d_{1}^{2}+r_{n}^{2}}}+{\sqrt {d_{2}^{2}+r_{n}^{2}}}-D=n{\frac {\lambda }{2}}

Assuming the distances between the antennas and the point $P$ are much larger than the radius, expanding the roots in series and retaining the first two terms, the expression simplifies to:

{\frac {r_{n}^{2}}{2}}\left({\frac {1}{d_{1}}}+{\frac {1}{d_{2}}}\right)=n{\frac {\lambda }{2}}

which can be solved for $r_{n}$ :[3]

r_{n}={\sqrt {n{\frac {d_{1}\ d_{2}}{D}}\lambda }},\quad d_{1},d_{2}\gg n\lambda ,

For a satellite-to-Earth link, $d_{2}\approx D$ and:[4]

r_{n}\approx {\sqrt {nd_{1}\lambda }}

Extended content

Note that when $d_{1}=0$ or $d_{2}=0\implies r_{n}=0$ , which implies that the foci coincide with the vertices of the ellipsoid. This is not correct and it's a consequence of the approximation made. Setting the point $P$ to one of the vertices it's possible to obtain the error $\epsilon$ of this approximation:

\epsilon +\left(\epsilon +D\right)-D=n{\frac {\lambda }{2}}\implies \epsilon =n{\frac {\lambda }{4}}

Since the distance between antennas is generally tens of km and $\lambda$ of the order of cm, the error is negligible for a graphical representation.

Maximum clearance

For practical applications, it is often useful to know the maximum radius of the first Fresnel zone. Using $n=1$ , $d_{1}=d_{2}=D/2$ , and $\lambda =c/f$ in the above formula gives

F_{1}={1 \over 2}{\sqrt {\lambda D}}={1 \over 2}{\sqrt {cD \over f}},

where

D

is the distance between the two antennas,

f

is the frequency of the transmitted signal,

c

≈ 2.997×10⁸ m/s is the speed of light in the air.

Substitution of the numeric value for $c$ followed by a unit conversion results in an easy way to calculate the radius of the first Fresnel zone $F_{1}$ , knowing the distance between the two antennas $D$ and the frequency of the transmitted signal $f$ :

$F_{1}\mathrm {[m]} =8.656{\sqrt {D\mathrm {[km]} \over f\mathrm {[GHz]} }}$
$F_{1}\mathrm {[ft]} =36.03{\sqrt {D\mathrm {[mi]} \over f\mathrm {[GHz]} }}$

gollark: Or booleans of lists.

gollark: IOYK HAS ELLK

gollark: I think there's a reverse state monad in which somehow the `s` flows in the opposite direction to the `a`.

gollark: Haskell.

gollark: Basically, I want to take a discord triple-backtick-delineated codeblock which has some extra stuff ending with a known string before it and extract its contents and language.

References

Coleman, Westcott, David, David (2012). Certified Wireless Network Administrator Official Study Guide. 111 River St. Hoboken, NJ 07030: John Wiley & Sons, Inc. p. 126. ISBN 978-1-118-26295-5.CS1 maint: location (link)
"Fresnel Zone Clearance". softwright.com. Retrieved 2008-02-21.
Tomasi, Wayne. Electronic Communication Systems - Fundamentals Through Advanced. Pearson. p. 1023.
Braasch, Michael S. (2017). "Multipath". Springer Handbook of Global Navigation Satellite Systems. Cham: Springer International Publishing. pp. 443–468. doi:10.1007/978-3-319-42928-1_15. ISBN 978-3-319-42926-7.

This article incorporates public domain material from the General Services Administration document: "Federal Standard 1037C". (in support of MIL-STD-188)

External links

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.

[1] Coleman, Westcott, David, David (2012). Certified Wireless Network Administrator Official Study Guide. 111 River St. Hoboken, NJ 07030: John Wiley & Sons, Inc. p. 126. ISBN 978-1-118-26295-5.CS1 maint: location (link)

[2] "Fresnel Zone Clearance". softwright.com. Retrieved 2008-02-21.

[3] Tomasi, Wayne. Electronic Communication Systems - Fundamentals Through Advanced. Pearson. p. 1023.

[Braasch_2017_pp._443–468-4] Braasch, Michael S. (2017). "Multipath". Springer Handbook of Global Navigation Satellite Systems. Cham: Springer International Publishing. pp. 443–468. doi:10.1007/978-3-319-42928-1_15. ISBN 978-3-319-42926-7.