Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [openswan]

129 questions
0
votes
0 answers

Can't connect Cisco 2621 to AWS EC2 Openswan site to site vpn

I am configuring Site-to-Site vpn between my home Cisco 2621 router and Amazon EC2 instance running openswan. I keep on getting the following message on the openswan server: " NO_PROPOSAL_CHOSEN " My Cisco 2621 router config and Openswan config are…
user1896576
  • 21
  • 2
0
votes
0 answers

OpenSwan VPN IPSEC Tunnel Connection

I was hoping this website would be able to help with solving this issue since I've been running in circles on my end! I am using OpenSwan to setup an IPSec tunnel between a VPN server on Rackspace and a VPN server on AWS. I've gone through several…
Nare
  • 55
  • 2
  • 10
0
votes
1 answer

Malformed Payload recieved from juniper firewall to libreswan while setting up an IPSec Tunnel

I have a CentOS system with libreswan behind a router with static IP, and I have been trying to setup an IPSec tunnel with a server at remote location having juniper firewall. The IPSec VPN settings on the remote server are done via firewall. I have…
packet
  • 3
  • 3
0
votes
1 answer

openSwan VPN is up can't ping remote subnet

When I run the command ipsec auto status i get the following output: ...... 172.16.255.1/32===104.131.13.155<104.131.13.155>:17/1701...41.203.65.124<41.203. 65.124>===10.100.108.51/32; erouted; eroute owner: #13 ....... 000 #13:…
Oladipo Olasemo
  • 111
  • 6
0
votes
1 answer

OpenSwan on Amazon EC2 - max number of retransmissions reached STATE_MAIN_I3. Possible authentication failure:

We are communicating with one of our clients over a VPN Tunnel. Openswan tunnel was working perfectly fine before. Today we attached an Elastic IP to the server and rebooted. Since then the tunnel is not starting up. These are the steps we have…
Gaurav Srivastava
  • 101
  • 2
0
votes
1 answer

Can't ping public endpoints when IPSec tunnel is up

I'm using openswan to link two machines via IPSec. The tunnel comes online fine and I have connectivity to each endpoint via the VPN. However, when the tunnel is up, I lose connectivity to the public endpoint IP addresses. For example, pinging site…
user98651
  • 95
  • 1
  • 2
  • 11
0
votes
1 answer

Openswan L2TP setup to allow admin user access to AWS VPC

I've got an ssh bastion host, but managing the ssh whitelist is annoying, opening ssh to the world is suboptimal. I'd like to tuck a vpn server in front. Can't get openvpn to stay connected for more than an hour (I'm using 2fa and either openvpn or…
jorfus
  • 715
  • 7
  • 14
0
votes
1 answer

IPsec VPN between Fortigate 60C and openswan up, but no traffic

I get visual confirmation that the tunnel is working from the fortigate GUI but, it also says i don't have 1 byte of traffic, the linux server also confirms the tunnel is open but i can't ping nowhere, my conn conn office #left side is home …
Julio Villalba
  • 41
  • 1
  • 5
0
votes
1 answer

CentOS 7 ipsec hardware rngd erorr

ipsec verify Hardware RNG detected, testing if used properly [FAILED] Hardware RNG is present but 'rngd' is not running. No harware random used! Someone suggest to edit /etc/sysconfig/rngd, add following line EXTRAOPTIONS="-r…
Jichao
  • 2,937
  • 4
  • 17
  • 14
0
votes
1 answer

OpenSwan Dead Peer Detection for Mac WIFI clients

I am running an OpenSwan server to facilitate client-server connections into a secure data centre. I have a problem with the standard L2TP over IPSEC client in MacOS, specifically when using WIFI. When I connect for the first time, it works fine.…
Garreth McDaid
  • 3,399
  • 26
  • 41
0
votes
0 answers

Site-to site Configuration between OpenSwan and Cisco ASA

I am making site-to-site vpn connection using amazon ec2 linux and cisco asa router ( please note i donot have access to router only configuration is provided.) CISCO ASA CONFIGURATION : Palisades Peer: xx.xx.xxx.xxx …
Himanshu Singhal
  • 1
  • 1
  • 1
0
votes
0 answers

iptables DNAT packets into an openswan IPSEC tunnel

I have the following network setup: +-----------------------------------+ | | +------------------------+ | …
Christian Anton
  • 1
  • 1
0
votes
0 answers

Openswan malfunction since update

For security reasons i performed and update from a previous version of openswan to U2.6.32/K2.6.18-194.el5 (netkey) Since that moment i've been experiencing constant tunnel drops, i've checked the /var/log/secure log but failed to id the…
Alonimus
  • 36
  • 5
0
votes
1 answer

IP Addresses over IPSec

I've got four hosts setup as follows: I've got an IPSec tunnel via OpenSwan over the internet between Servers B and C. Servers A and D are configured to route traffic to the other via B and C respectively. Servers A and B are on one private…
Alex
  • 29
  • 2
0
votes
0 answers

OpenSwan IPsec connection drops after 30 seconds

I'm trying to connect from my Linux Mint 16 box to a CloudStack server through IPsec L2TP. Building up the connection works (pings work across the tunnel). However 30 seconds later the IPsec tunnel gets terminated out of the blue. What could cause…
drcore
  • 1
  • 3
1 2 3
…
8 9