Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [hba]

HBAs are host bus adapters. They are a type of special purpose network card specifically designed for talking to storage systems. Typically via Fiber Channel, SCSI or eSATA.

Host Bus Adapters are special purpose "network" devices for talking to storage systems. They use storage protocols (SCSI, Fiber Channel, etc.) to communicate with a SAN or set of disks.

They can be expansion boards installed in a server, or an on board option, much like 'conventional' network cards.

Because of the specific needs of storage they tend to be lower latency than you would get from a conventional ethernet network card.

90 questions
1
vote
1 answer

Is there a list of linux compatible RAID/HBA cards?

I purchased an LSI Logic HW RAID controller on ebay without doing much research and discovered the hell of 10-year old proprietary drivers and command line tools with no documentation. I'd like to avoid that experience again, and so I'm looking at…
bweber13
  • 141
  • 4
1
vote
1 answer

HP Proliant ML350 Gen9 Server with Debian Linux Kernel Does not boot HBA mode SAS drives. initramfs timeout. long disk detection. disks not recognized

This is what I have: 1- HP Proliant ML350 Gen9 with SAS LFF (3.5 inch) Disks running in HBA mode. 2- Debian Linux version 10 (Buster) Kernel Does not boot HBA mode SAS drives normaly. I have to go to recovery mode in order to boot then press ctrl+D…
superlinux
  • 141
  • 5
0
votes
1 answer

Possible to use SAS-2 and SAS-3 HBA in the same system?

I'm wondering if it is possible to use a SAS-2 HBA in a "SAS-3" system. I have a Supermicro X11DPH-T and have attempted to install an LSI 9201-16e. From what I understood (which may be wrong), a PCIe 2.0 card may be installed in a PCIe 3.0 slot,…
Liczyrzepa
  • 455
  • 4
  • 13
0
votes
1 answer

Configure single LTO tape drive over Fiber Channel HBA

How do you set up a single tape storage drive over an FC HBA? As far as I can tell, these things are not "plug and play". The tape drive I bought is an lto-5 FC taken from a tape library. I have everything on and plugged in, but I am not seeing the…
teziroct
  • 1
  • 2
0
votes
1 answer

How is FC HBA card compatibility on Ubuntu? [Solved]

I have a server running on Ubuntu 16.04, and need to connect this server to a SAN storage via FC. I wonder which kind of HBA FC card does Ubuntu support? For example, this card is suggested by a local supplier, but Ubuntu is not in supported…
Hiep Ho
  • 101
  • 3
0
votes
0 answers

LSI 9211-8 or 9650se for a ZFS Pool

I'm putting together a white box (smartos) for our dev team with some of the leftover hardware we have. The server chassis I'm going to use has 8 swappable drives and I'm trying to determine which hba card to use for the ZFS Pool. I have both the…
chris
  • 103
  • 5
0
votes
0 answers

RAID Controller Firmware Issue

Background: I'm a Linux newbie with very limited knowledge, I wanted to build a RAID 10 for our startup after experiencing a complete loss of several terabytes of data from Dropbox recently. Setup: I spun up an Ubuntu 16.04 (Desktop) machine and…
Alex Iravani
  • 1
0
votes
1 answer

CentOS7 and LSI-9200-8E: How to see all external drives?

I'm working on a low-budget configuration change that involves a migration from a working reflashed IBM M1010 (LSI9220-8i) environment to a newer server running an LSI9200-8e SAS HBA. Everything works fine on the old server, but it uses lots of…
Steve Bonds
  • 874
  • 2
  • 10
  • 19
0
votes
1 answer

Compatibility criteria between PCIe component and the motherboard

I have a Gigabyte (GA-B85-HD3 2.0) motherboard and an LSI SA9201-16e, however am not seeing the BIOS configuration menu for the card on boot. The motherboard only has one PCIe slot that can accept the card (8x 2.0), the graphics card slot (16x 3.0).…
J Collins
  • 191
  • 7
0
votes
3 answers

Reconnecting SAS equipment

I need to reconfigure the cabling between some LTO tape drives and a server. Are they plug and play or do I need to do any configuration? From what I've read so far, it seems that recycling the power on the server and the drives should be enough. We…
Rich M
  • 273
  • 2
  • 15
0
votes
2 answers

install grub in a usb and boot proxmox from another drive

Good morning my friends! I'm tryng a solution before buy some new hardware. So this is my situation: I have some beautifull hp dl360p gen8 that comes with an p420i hardware raid controller. What I'm tryng to build is a proxmox+ceph cluster for my…
silvered.dragon
  • 111
  • 3
0
votes
0 answers

How to find wwn through EFI Shell?

I have not installed any OS in the server. HBA card is attached to the server and after power ON it enters into EFI shell. I entered below command and it show FC driver drivers Output like 17F 00000629 D N Y 2 0 HP Fibre Channel Driver…
KKD
  • 101
  • 4
0
votes
1 answer

How to find out driver and firmware version of my ESXi Fiber Channel HBA? (via SSH)

I have an ESXi 5.5 Server (HP DL380 G7). How can i figure out the driver and firmeware version of my HP-QLOGIC Fiber Channel HBA via SSH? I think i am too stupid... :-/ Thx for help.
frupfrup
  • 853
  • 3
  • 13
  • 27
0
votes
1 answer

HDD LEDs stopped working after exchanged raid controller in HP DL380 G5

I recently went ahead and exchanged the p400 RAID controller in my HP DL380 G5 server with an LSI HBA card (SAS 9207-8i). I did this to get better disk compatibility, and I didn't need RAID functionality. I popped a few Samsung SSDs in the machine…
Benjamin Hammer Nørgaard
  • 143
  • 4
0
votes
1 answer

Can I use Emulex LP9802DC-E Dual Channel PCI-X host bus adapter to replace failed LP9002DC-E?

One LP9002DC-E HBA card has failed, and I have trouble finding an exact replacement. However, I was able to find a supplier for LP9802DC-E. From what I can understand on paper, the only substantial difference is that LP9002DC-E uses 66MHz PCI-X, and…
user1985553
  • 103
  • 2
1 2 3 4
5
6