Xbox One S All Digital Edition Power Supply Replacement

Written By: Jules Hajjar
  • Comments: 5
Xbox One S All Digital Edition Power Supply Replacement

Difficulty

Moderate

Steps

16

Time Required

45 minutes - 1 hour

Introduction

This guide showcases how the power supply can be replaced in case of a power issue on the Xbox One S All Digital Edition (Model 1681). Symptoms of a faulty power supply may be the Xbox turning on and off randomly or not turning on at all. Note that the entire console will have to be disassembled to properly replace the power supply without damaging other components. Disconnect all cables prior to disassembly.

  1. pQOTEpEZdGFtnU43
    pQOTEpEZdGFtnU43
    4AxKp1UNjhFsaaoC
    fXDtF2XrbZKCsQcr

    • Position the iFixit Opening Tool's riveted edge in between the top and bottom cover of the plastic enclosure.

    • Apply downward pressure on the iFixit Opening Tool until the security clip unlocks.

    • Repeat on different points of the plastic enclosure until the bottom cover is removed.

  2. PZgrJYjK2NxpISY1
    PZgrJYjK2NxpISY1
    jMOFSSw4qSCfPmAi

    • Remove the six 50 mm green screws (labeled F1-F6) from the metal chassis using a Torx 10 screwdriver.

    • These screws hold the top cover of the plastic enclosure to the chassis.

  3. INKa3TY3oQ2KBNhj
    INKa3TY3oQ2KBNhj
    rOtHrWrrFSEHA41u

    • Apply pressure to peel off the sides of the casing.

    • Separate the metal chassis from the top cover, lifting the back of the chassis up and away from the top cover.

    • The plastic back panel is meant to stay attached to the metal chassis.

  4. rX4AYhcYIAOLKTHY

    • Flip the metal enclosure so that the fan cover is on top.

  5. uHZC6KVdZAItFmSi
    uHZC6KVdZAItFmSi
    lEH54BlQTFmZwGDx

    • Remove the two 15mm screws from the front panel using the Torx T8 screwdriver.

  6. IOlnJ1k3CN6qdiMl
    IOlnJ1k3CN6qdiMl
    DKxqD4WS1XEVkIgj
    i2fdWxw3rRmwrUWo

    • Carefully slide the top metal case off the frame.

    • This may require shifting the case side to side as you slide up.

  7. kIMhFOvMcnNheJK5
    kIMhFOvMcnNheJK5
    mYKdsxXpCgsLpiNJ

    • Remove the three 15 mm screws with the Torx T8 Security Bit Screwdriver.

    • The top of the metal chassis has been removed in the picture, but is not necessary for the replacement.

  8. hAenPQWWq1dDuyW3

    • Carefully remove the WiFi Card from the metal chassis.

    Hello , I have a question.

    Can I play the xbox one all digital fully offline, without the wi-fi card plugged into it ?

    Il Lupo -

    You should be able to play offline without the card. This is assuming you downloaded whatever games you plan to play before removing the card.

    Sebastian Rosso -

  9. pmPxKamgv3RVeWp6
    pmPxKamgv3RVeWp6
    rYd6mi1yeoTTtRjr

    • Remove the four 15mm screws attaching the IR Blaster to the metal chassis with the Torx T8 Security screwdriver.

  10. IOLJsZyg6LCUJl2c
    IOLJsZyg6LCUJl2c
    UNXPcWlSQZg4FiQF

    • Carefully remove the IR Blaster from the metal chassis.

    • The connector is very fragile. Make sure you pull the board away from the case and not sideways.

  11. 2CUFWgLMTuE6iYHg
    2CUFWgLMTuE6iYHg
    ve6cGoAFv2EXehV2

    • Remove the eight 10mm screws from the bottom of the metal casing using the Torx T9 screwdriver.

    • Remove the four 15mm screws from the bottom of the heatsink fastener using the Torx T8 screwdriver.

  12. bVGBPhFXAjV4BNrQ
    bVGBPhFXAjV4BNrQ
    iuJpTTEFDoFE2YRy
    IE1F6LIMBoNOIeca

    • Remove the two plastic pieces from the motherboard.

  13. 26Q1woeyNdGijsgE
    26Q1woeyNdGijsgE
    OIY1FXeEXd1cRRcT
    WLUvwGl5lMVWxghm

    • Lift the motherboard up from the metal chassis.

    • The motherboard should easily separate from the metal chassis.

  14. eOHvBxKGc2w2ydfx
    eOHvBxKGc2w2ydfx
    OVPmXjTOeFeExsEY
    tbULXiJ2S5ZFOxZL

    • Gently lift the hard drive to free up some space around the power supply.

  15. yhslu3ZTkOdOVk3K
    yhslu3ZTkOdOVk3K
    4GM2vS5rVSHyMm5n

    • Lift the power supply up and away from the motherboard.

  16. jUKfSOuy65em43P2
    jUKfSOuy65em43P2
    LuniQR52jTEXeoG2

    • Disconnect the six pin connector from the motherboard.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Jules Hajjar

Member since: 10/10/19

1531 Reputation

3 comments

I replaced the power supply and my Xbox still isn't turning on. I used a power supply I got from this website. Please help

William Oliver -

Another issue could be the power button on the front power board. If possible, you could try to replace that as well.

Jules Hajjar -

replace the PSU and still boots up and shuts off

imafuxer -