Sony Cyber-Shot DSC-W330 LCD Display Replacement

Written By: Hunter Stewart
  • Comments: 1
Sony Cyber-Shot DSC-W330 LCD Display Replacement

Difficulty

Moderate

Steps

7

Time Required

15 minutes

Introduction

  1. gEtH4L1kZ4oQbRbR
    gEtH4L1kZ4oQbRbR
    eIg51RPwZrOSsmJp
    oG2nypRSTDyEOx2O

    • Begin by placing the camera flat against a surface and remove the nine (9) black screws. Each screw is of the same length and can be used interchangeably

    • Note: There are two (2) screws on each side, and five (5) on the bottom edge.

  2. GXgfjnRBDkTYfH3a
    GXgfjnRBDkTYfH3a
    nHBtReACUmmyKP1I
    ITEPPkaMWsaQAGwd

    • Use a plastic opening tool to carefully pry off the front casing.

    • Be careful to not to force the casing off. Simply move around the entire case separating where needed.

  3. YwjOJiFKiAbpes22
    YwjOJiFKiAbpes22
    S4BPtEjs5NO1R2nE
    DsEB1UfiFvYAmKEO

    • Flip the camera over 180 degrees and similarly pry off the rear casing.

  4. kXQkiHcFwLXNxvuS
    kXQkiHcFwLXNxvuS
    kWNGWIbpCSGDIPwP
    JrwCvCYUDJUFSNOq

    • Once the outer casings have been removed, the silver side trim should come loose from the camera.

    • Place the camera with the lens facing down. Use the plastic opening tool to pry off the side panel with the USB plug.

    • Note: If you wish to remove the top cover, see the LCD Display Replacement to remove the LCD screen before continuing to Step 5

  5. bti6XaqPImhSQSeX
    bti6XaqPImhSQSeX
    UyaKDDF6I6HElT1N
    n3smEJmqWqvpChbM

    • Place the camera with the lens facing down. Use the phillips head screwdriver to remove the silver screw in the corner near the photo capture button.

    • Flip the camera over. Use the plastic opening tool to detach the black clip near the capture button.

    • Grasp the top cover and gently remove it from the camera body.

  6. 2komHQFj63B2rLL5
    2komHQFj63B2rLL5
    uh1XG2KCmIp2FYTD
    YHrtULjFgGLtLFFG

    • After the outer casing is removed, lay the device display side up

    • Gently pry the LCD screen from the body of the camera.

    • Be careful not to damage the ribbon cables, they are still attached to the camera.

  7. OKet6DpEena1vokI
    OKet6DpEena1vokI
    JTfBNQ1WIPQPsKEF
    F1VusZJRwQYDNLQK

    • Flip the LCD Assembly around the edge of the camera

    • Note: Be careful not to rip the assembly from the camera. It is still attached by the ribbon cables!

    • Use the plastic opening tool to gently pry up the black tab locking the large ribbon cable to the battery housing.

    • Grasp the LCD display with your fingers and gently pull the large ribbon cable out of the connector.

    • The LCD display is now detached from the camera.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Hunter Stewart

Member since: 18/10/13

411 Reputation

One comment

What LCD screen can i replace it with

Matnor3339 -