Nintendo Switch Lite Shield Plate Replacement

Written By: Craig Lloyd

Comments: 11

Nintendo Switch Lite Shield Plate Replacement

Difficulty

Moderate

Steps

Time Required

15 - 30 minutes

Introduction

Follow this guide to remove or replace the shield plate inside the Nintendo Switch Lite.

The Switch Lite uses JIS screws, but you can use a Phillips screwdriver in a pinch. Be very careful not to strip the screws. iFixit's Phillips bits are designed to be cross-compatible with JIS-style screws.

Note: Removing the shield plate will require cleaning off thermal paste and reapplying it to the heatsink.

Tools

Step 1

Before beginning this repair, make sure that the device is completely turned off.
Use a Y00 screwdriver to remove the four 6.3 mm-long screws securing the back panel.
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

All my screws got stripped any ideas on how to remove?

Almost A Mammal -

A Y0 screwdriver seemed to work better for me.

Tommy Morrill -

What type of screw driver do I use to un screw the screws and which way

Luca Capito -

Y 0.6 was all I had but it seemed to fit perfectly

Trevor -

Step 2

Use a JIS 000 driver or an official iFixit PH 000 driver to remove the following screws securing the back panel:
Two 3.6 mm-long screws on the top of the device
Two 3.6 mm-long screws on the bottom of the device
To prevent these tight screws from stripping, apply firm downward force, work slowly and try a different screwdriver if the screws won't come out.

I accidentally stripped the back screw and now I can't open it. I removed all the other screws. What should I do?

tiggytiger555 -

Step 3

Insert an opening tool into the left speaker grille on the bottom of the device.
Twist the opening tool to release the clips securing the back panel.
Avoid inserting the opening tool further than required to prevent damage to the speaker module.

Step 4

Slide the opening tool around the bottom-left corner to release the clips on the left side of the device.

Step 5

Insert an opening tool into the right speaker grille on the bottom of the device.
Twist the opening tool to release the clips.
Avoid inserting the opening tool further than required to prevent damage to the speaker module.

Step 6

Slide and pry the opening tool around the bottom-right corner to release the clips on the right side of the device.

Step 7

Continue sliding and prying the opening tool along the gap on the top of the device to release the clips.

Step 8

Lift the bottom edge of the back panel, opening it like a book.
Remove the back panel.

Step 9

Use a JIS 000 driver or an official iFixit PH 000 driver to remove the following four screws:
Three 3.1 mm screws
One 4.5 mm screw

There are four screws instead of three mentioned

Khurram Chaudry -

it doesnt mention 3 anywhere, and it labels all four

Ezi -

With how easy it seems to be to do serious damage with the next few steps, I figured I'd say that realistically you can skip steps 9-13 when doing this repair. While they provide a bit of extra security by disconnecting the battery, the left stick is completely accessible and replaceable without touching the heat shield or anything underneath (And steps 17 and 18 disconnect power from the daughter board regardless).

Nate -

i stripped a &&^&^$^ screw

SpongebobFan254 -

Well I actually removed the screw right next to the 4.5 screw. I did not realize it till my son showed me why the plate wouldn't release. Ha ha, it's funny now but yeah not a big deal. I could have bent it badly assuming I took all screws out though. For anyone reading this before going in. 👍

Toastninja -

Step 10

Use a spudger or your fingers to lift the shield plate up and out of the device.
You may feel a bit of resistance. This is normal, since the shield plate is slightly bonded to the heat sink with thermal paste.
Remove the shield plate.
Clean off the old thermal paste from the shield plate and heat sink using isopropyl alcohol and a microfiber cloth. Apply new thermal paste to the heat sink before reassembly.