MacBook Air 2022 (M2) Headphone Jack Replacement

Written By: Spencer Day
  • Comments: 1
MacBook Air 2022 (M2) Headphone Jack Replacement

Difficulty

Moderate

Steps

17

Time Required

30 - 45 minutes

Introduction

Use this guide to replace the headphone jack in your MacBook Air 2022 (M2).

  1. lquDimvZWHVcGkIF
    lquDimvZWHVcGkIF
    MrBPlfJiyDeCh3Xy
    GiVPDUTQKCcVHQEp

    • Before you begin, discharge your battery below 25%, as a charged lithium-ion battery can be dangerous if accidentally punctured.

    • Power off your MacBook Air and unplug all cables.

    • Close the display and flip the laptop upside down. Keep the lid closed until you've physically disconnected the battery.

  2. UU3OByKvXHdj5Y2H
    UU3OByKvXHdj5Y2H
    IiKX3lhcjAkhlYAf

    • Use a P5 Pentalobe driver to remove the four 6.4 mm screws securing the lower case:

    • Two screws with a short threaded portion near the hinges

    • Two screws with a long threaded portion near the front of the MacBook

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

  3. dokINhbATeVrKXtr
    dokINhbATeVrKXtr
    TjUylLnpiHfWk2sV
    m6fVPUBtNhtoYYHl

    • Apply a suction handle to the center of the lower case's front edge.

    • Pull up on the suction handle with strong, steady force to create a small gap between the lower case and the frame.

    • Insert an opening pick into the gap.

  4. BoDqyqxbGBlggTvo
    BoDqyqxbGBlggTvo
    pY1Qrw1jHD1iDd2b
    UBVsUaYNRIMIAlaU

    • During the next two steps you'll feel and hear four snapping clips release. If a clip doesn't release, insert your opening pick farther and try again.

    • Slide the pick to the bottom right corner to release the first clip.

    • Slide the pick around the corner and up the right edge to release the next two clips.

  5. BkegaQVYCGs6e6uo
    BkegaQVYCGs6e6uo
    uARqMGT1yaE2uhOn
    Lo1ugnNCtcNL1Qyj

    • Insert the opening pick in the original gap created with the suction handle.

    • Slide the opening pick to the bottom left corner and up the left edge to release the three remaining snapping clips.

  6. JxjCoOqbtL6riXKd
    JxjCoOqbtL6riXKd
    bXZHWpvubTHOOBVP
    AuNBkdMIobCVlYIC

    • Four sliding tabs along the back edge of the MacBook firmly secure the lower case. Separating these tabs requires a lot of force—consider using gloves to protect your hands from the sharp edges of the lower case.

    • Keep the lower case flat and firmly pull it straight away from the back edge, one corner at a time, to disengage the sliding tabs.

    • Don't pull up until the cover is completely separated.

  7. dQ1idM13kbRF6NQC
    dQ1idM13kbRF6NQC
    UqDpUWQXDrMQDWSf
    bXP3i6XCG1BSaeBP

    • Remove the lower case.

    • During reassembly:

    • Set the lower case in place and align the sliding tabs with the screw heads they slide over. Press down and slide the lower case toward the back edge to engage the tabs—it'll stop sliding as the tabs engage.

    • When one side is engaged, it may push the other out of alignment. Check both sides as you push, there should be no gap along the back edge.

    • Once the lower case is flush with the frame, press down firmly along the perimeter to engage the four snapping clips.

    • You'll hear and feel a distinct click as each clip snaps into place.

  8. DP2BQNffNgdKM1dp

    • Use a T3 Torx driver to remove the two 1.5 mm screws securing the battery connector cover.

    • Due to screw variances, you may need to use a T4 Torx instead. Keep this in mind whenever you encounter T3 Torx screws during this repair.

  9. 2UVCE1lqOt3ViR3I
    2UVCE1lqOt3ViR3I
    JCSnLNLOpWoUBEM2

    • Remove the battery connector cover.

  10. TLUsv2wJrhFsJtLN
    TLUsv2wJrhFsJtLN
    TnjVCuugvheTD3RO

    • Use an opening pick to pry up and disconnect the battery connector.

  11. s6djZEXH6AGUsesX
    s6djZEXH6AGUsesX
    cRuIff3pTNGbXEW2

    • Use a T3 Torx screwdriver to remove the two 1.5 mm screws securing the headphone jack connector cover.

  12. B1tRHjqBWZ66uL51
    B1tRHjqBWZ66uL51
    ApAyHuHZfdXQZuuF

    • Remove the headphone jack connector cover.

  13. VfquHsV3jdHIWsES
    VfquHsV3jdHIWsES
    nPfTYCFFLedR3TuU

    • Use the pointed end of a spudger to pry up and disconnect lid angle sensor press connector.

  14. cZudPVlU1tFCbxrW

    • Peel the lid angle sensor cable from the top of the headphone jack and move it out of the way.

  15. nERDUng1qTtaNKdb
    nERDUng1qTtaNKdb
    wEEYt4vnmiFvSlXs

    • Disconnect the headphone jack press connector.

  16. AYG1nvnnuuUotXp6
    AYG1nvnnuuUotXp6
    Q6alBhBjFbE3aGx6

    • Use a T5 Torx screwdriver to remove the two 4.8 mm screws securing the headphone jack.

  17. pCXrsiHoyBlWT4XQ
    pCXrsiHoyBlWT4XQ
    WZDVtutlxO5KMBFU
    bSru1GyV6ChZTQkV

    • Tilt the headphone jack towards the left edge of the laptop, dislodging it from its recess.

    • Lift the headphone jack straight up and remove it.

Conclusion

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before you install it.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting or check out our Answers community for help.

Author

Spencer Day

Member since: 14/09/22

49372 Reputation

0 comments