Kitchen Gourmet WM-6105 Disassembly

Written By: Giulia Puppin
  • Comments: 0
Kitchen Gourmet WM-6105 Disassembly

Difficulty

Easy

Steps

11

Time Required

20 - 30 minutes

Introduction

This is a disassembly guide for the Kitchen Gourmet Electric Hot Pot Model No. WM-6105 that allows you to access all of the components without permanently damaging any of them. This disassembly only requires use of a screwdriver. Further disassembly to replace individual components would require soldering, which is not covered in this guide.

  1. vjlWDHaJhQiVlrnW
    vjlWDHaJhQiVlrnW
    nRqEdMfRCdf3Vdej
    VSmSmKuRW2qH6LsS

    • Remove the three rubber feet.

    • You can pinch them quite hard to pull them out as they are not held in by adhesive.

  2. ulmghUTNPLMNKvZo
    ulmghUTNPLMNKvZo
    APKw3HYYWRRMKWMX
    uGXeF2V3cmDatHov

    • Remove the 7 12 mm Phillips #1 screws.

    • The white plastic bar holding two of the screws comes loose once they are unscrewed.

  3. DCNOQTABAxLOaYFW

    • Remove the white plastic bar holding the cord.

  4. qSFtOxORDCDDgH2I
    qSFtOxORDCDDgH2I
    frLQGcMtVEoWFNdM

    • Push the cord through the opening while pulling the base away from the body.

  5. IjrdOAYGM6fQ5Go6
    IjrdOAYGM6fQ5Go6
    lAyqlfnlj21Bv1OF
    xOLCYyGPWgNG1Suf

    • Flip the hot pot so it it right-side-up.

  6. UfpBpUND5gnrBipk
    UfpBpUND5gnrBipk
    HCftXF4P2acVGWJj
    YvSGYn2DyFmckVCA

    • Unscrew the single 8 mm Phillips screw holding the temperature dial in place.

  7. oxJ1cmYSUugIQuQs
    oxJ1cmYSUugIQuQs
    RZouc6NfjZaKGTvi
    SAykoSD3HbYd3wXP

    • Remove the dial from plastic housing knob.

  8. vDWdBdyA1qZnFtoW
    vDWdBdyA1qZnFtoW
    yTWnJIgmhloUHny2

    • Unscrew the eight 6 mm screws holding in the metal brackets.

  9. tvugGVMssisuL1L2
    tvugGVMssisuL1L2
    U4Rr5E2GUoBuHPoo
    TFQdXPwELdWhXrXV

    • Remove the metal brackets.

  10. SlQHHYQ6TQnDUtRu
    SlQHHYQ6TQnDUtRu
    VRxNpeS2UFmHp2yr

    • Unscrew the single screw holding down the clamp that connects the thermal switch (black cylinder) and the white wire to the body of the hot pot.

  11. WthwxWcy1EkGLYJ4
    WthwxWcy1EkGLYJ4
    NbKkGoT1xQmPtR5C
    EQALGMKJYqkws4Rx

    • Remove the clamp holding down the thermal switch and white wire.

    • There is thermal grease between the thermal switch and the metal base of the hot pot. Once the bracket comes off, and the switch comes unattached, you may need to reapply it if you plan to reattach the switch.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Giulia Puppin

Member since: 13/09/23

243 Reputation

0 comments