Introduction

This guide demonstrates how to disconnect the antenna cables from the daughterboard in your Dell Latitude 7410 laptop.

  1. ZGA51OPDJSxC2TYs
    • Use a Phillips screwdriver to loosen the eight captive screws securing the back cover.

  2. FLbNUScF6GTmQtVF
    FLbNUScF6GTmQtVF
    4AGQckNfxEpKoEKU
    • Insert an opening pick between the right edge of the back cover and the frame, just below the middle right screw.

  3. DTlPw2pqGIDkkYOf
    DTlPw2pqGIDkkYOf
    CUuCmdhYkBXTfkN2
    • Slide your pick along the right edge to release the clips securing the back cover.

  4. 1OHWpDCm1cXCoZYp
    1OHWpDCm1cXCoZYp
    slJJSckwBnuAAYor
    PYsuRNtnNHwJ6wCv
    • Insert your pick between the left edge of the back cover and the frame, next to the speaker cutout.

    • Slide your pick along the left edge to release the clips.

  5. x65QutnMkQPYHDWq
    x65QutnMkQPYHDWq
    XtCFfNqCafBooWsj
    UePh1xVQ2ittXubl
    • Insert your pick between the back cover and the right display-hinge to release the first clip along the back edge.

    • Slide your pick toward the left hinge until the second clip releases.

  6. qcvfJR5d3mXGNSqY
    qcvfJR5d3mXGNSqY
    EV6QgyotJEQ2Irhk
    • Insert your pick between the front edge of the back cover and the frame, just to the right of the bottom left screw.

    • Slide your pick toward the right edge until the front edge releases from the frame.

  7. oXxrAtcp2JqMPOsF
    oXxrAtcp2JqMPOsF
    GpA6xUysqbjJU5Fr
    • Remove the back cover.

  8. TyeDs4aNSeeQOfTG
    TyeDs4aNSeeQOfTG
    6VSAPrDuD1m6mYjw
    • Grab the black pull tab on the head of the battery connector and pull straight up to disconnect it.

  9. 1MsTNoGoMEmsVVGA
    1MsTNoGoMEmsVVGA
    5tI4IH2JV4RoMwhj
    6asEvvFpnYe6gu2R
    • If your laptop doesn't come with a WWAN card, skip the next two steps.

    • Use the flat end of a spudger to pry up the WWAN card cover from its clips on the I/O board.

    • Remove the cover.

  10. NPo5mXebMlME2oat
    NPo5mXebMlME2oat
    dJGQMYSYMuuBuVt6
    n36qB5c4WISKKlJ6
    • Use your Phillips screwdriver to remove the 3 mm screw securing the WWAN cable bracket.

    • Remove the cable bracket.

  11. DxRRm6eUJGrxnmyI
    DxRRm6eUJGrxnmyI
    uegXa2RYtH5CUci1
    hBbIsOm4K4h1BpJW
    • Use your Phillips screwdriver to remove the 3 mm screw securing the antenna cable bracket.

    • Remove the antenna cable bracket.

  12. ifNYMSVJ6KN21TWQ
    ifNYMSVJ6KN21TWQ
    ZpNC5ar6HgWVRwwT
    cuYV1TyhDe1FegSU
    • Use your spudger to disconnect the antenna press connectors labeled 1 and 2 by prying the heads of their connectors straight up.

    • To re-attach press connectors, carefully align and press down on one side until it clicks into place, then repeat on the other side. Don't press down in the middle. If the connector is misaligned, the pins can bend and cause permanent damage.

  13. 3aHrkPQRqauSCrTo
    3aHrkPQRqauSCrTo
    aiulFCbFFZcitlgb
    MysuAIKYmWlVJDlX
    • This step shows a laptop that didn't come with a WWAN card. If yours has one, disconnect and remove it now.

    • Lift the antenna cables out from their cable routing on the I/O board and move them away from the board.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Clay Eickemeyer

Member since: 19/09/22

65190 Reputation

0 comments