WD-11

The WD-11 vacuum tube, a triode, was introduced by the Westinghouse Electric corporation in 1922 for their Aeriola RF model radio and found use in other contemporary regenerative receivers (used as a detector-amplifier) including the Regenoflex and Radiola series.

The WD11 and "RCA-11"[1] (and later simply named "11" by RCA[2] and Philips/Miniwatt[3]) have the following characteristics:

Socket: UV4 (also known as WD-4-Pin)
EIA/RETMA Base Diagram: 4F
Description: Detector Amplifier Triode
Filament: Directly-heated 1.1 V0.25 A
Plate (anode) Voltage: 90V135V maximum
Grid Voltage: -4.5V-10.5V
Plate Current 2.5 mA3.0 mA
Plate Resistance: 15.5 kilohms15 kilohms
Amplification Factor (mu): 6.66.6
Transconductance (gm or S): 0.425 mA/V0.44 mA/V
Power Output: (Po): 0.007 W0.04 W[4]
Grid-plate Capacitance (Cga): 3.3 pF
  1. RCA Receiving Tube Manual RC-13. 1937. p. 98.
  2. RCA Receiving Tube Manual RC-14. 1940. p. 157.
  3. "Miniwatt" Technical Data (6th ed.). Australia: The "Miniwatt" Electronics Division of Philips Electrical Industries Pty. Limited, N.S.W. 1958. p. 56.
  4. "WD 11". Retrieved 7 January 2013.

Drawbacks
Westinghouse WD-12
RCA UX-199

The WD-11's design was somewhat ill thought out, when the filament burns out it has a tendency to contact the plate, feeding high voltages back through the heater circuitry. It was replaced just a year later by higher performance tubes which were less likely to encounter this problem, Westinghouse Electric's WD-12 and General Electric's UX-199. No radios using the WD-11 tube were designed after 1924, RCA ceased production and issued a service bulletin describing how to retrofit existing sets to use the newer UX-199 triodes.

Collectiblity

Because of its rarity it has become one of the most valuable vacuum tubes in the world. New-old-stock units have sold for as much as US$180 and used tubes for over $100, more than the original price of the radios that use them. Collectors rarely, if ever use these tubes for fear of burning them out.

Substitution

Sets that use the costly WD-11 and UX-199 tubes can be modified to use the 1A5/GT octal power pentode (Which cost around $2.50) by wiring a 5.1 ohm resistor between the pins of the filament and fabricating an octal-to-four pin adaptor. The pin for the 1A5's suppressor is left unconnected and the screen connected to the plate.

The type 12 (also known as RCA-12) is electrically identical to the type 11, but with a more common UX4 base.

gollark: You should not let yourself be bound by the wrong and bad spending habits of the median family.
gollark: You might want to actually have savings, as a worrying amount of people apparently don't.
gollark: You might live in somewhere with higher cost of living, as many software types do.
gollark: This is also probably wrong. There are perfectly good reasons to spend more than the median family on some category, especially if the categories are particularly granular.
gollark: Oh, and lots of things (particularly computing equipment) are usable for fun *and* work purposes.

Here is a link on how to modify other tubes to use in place of a wd11:

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.