Optical fiber connector

An optical fiber connector terminates the end of an optical fiber, and enables quicker connection and disconnection than splicing. The connectors mechanically couple and align the cores of fibers so light can pass. Better connectors lose very little light due to reflection or misalignment of the fibers. In all, about 100 different types of fiber optic connectors have been introduced to the market.[1]

LC (top) and ST (bottom) optical fiber connectors, both with protective caps in place.

Application

Optical fiber connectors are used to join optical fibers where a connect/disconnect capability is required. Due to the polishing and tuning procedures that may be incorporated into optical connector manufacturing, connectors are often assembled onto optical fiber in a supplier's manufacturing facility. However, the assembly and polishing operations involved can be performed in the field, for example, to terminate long runs at a patch panel.

Optical fiber connectors are used in telephone exchanges, for customer premises wiring, and in outside plant applications to connect equipment and cables, or to cross-connect cables.

Most optical fiber connectors are spring-loaded, so the fiber faces are pressed together when the connectors are mated. The resulting glass-to-glass or plastic-to-plastic contact eliminates signal losses that would be caused by an air gap between the joined fibers.

Performance of optical fiber connectors can be quantified by insertion loss and return loss. Measurements of these parameters are now defined in IEC standard 61753-1. The standard gives five grades for insertion loss from A (best) to D (worst), and M for multimode. The other parameter is return loss, with grades from 1 (best) to 5 (worst).

A variety of optical fiber connectors are available, but SC and LC connectors are the most common types of connectors on the market.[2] Typical connectors are rated for 500–1,000 mating cycles.[3] The main differences among types of connectors are dimensions and methods of mechanical coupling. Generally, organizations will standardize on one kind of connector, depending on what equipment they commonly use.

In many data center applications, small (e.g., LC) and multi-fiber (e.g., MTP/MPO) connectors have replaced larger, older styles (e.g., SC), allowing more fiber ports per unit of rack space.

Outside plant applications may require connectors be located underground, or on outdoor walls or utility poles. In such settings, protective enclosures are often used, and fall into two broad categories: hermetic (sealed) and free-breathing. Hermetic cases prevent entry of moisture and air but, lacking ventilation, can become hot if exposed to sunlight or other sources of heat. Free-breathing enclosures, on the other hand, allow ventilation, but can also admit moisture, insects and airborne contaminants. Selection of the correct housing depends on the cable and connector type, the location, and environmental factors.

Types

Many types of optical connector have been developed at different times, and for different purposes. Many of them are summarized in the tables below.

Fiber connector types

Short name	Long form	Coupling type	Screw thread	Ferrule diameter	Standard	Typical applications	Notes	Image
Avio (Avim)	Aviation Intermediate Maintenance	Screw	?			Aerospace and avionics
ADT-UNI		Screw	?	2.5 mm		Measurement equipment
DMI	Diamond Micro Interface[4]	Clip	n/a	2.5 mm		Printed circuit boards
LSH or E-2000 [5]		Snap, with light and dust-cap	n/a	2.5 mm	IEC 61754-15	Telecom, DWDM systems;
EC		push-pull type	n/a		IEC 1754-8[6]	Telecom and CATV networks
ELIO		Bayonet	n/a	2.5 mm	ABS1379	PC or UPC
ESCON	Enterprise Systems Connection	Snap (duplex)[1]	n/a	2.5 mm		IBM mainframe computers and peripherals
F07				2.5 mm	Japanese Industrial Standard (JIS)	LAN, audio systems; for 200 μm fibers, simple field termination possible, mates with ST connectors
F-3000		Snap, with light and dust-cap	n/a	1.25 mm	IEC 61754-20	Fiber To The Home (LC Compatible)
FC	Ferrule Connector or Fiber Channel[7]	Screw	M8×0.75[8]	2.5 mm	IEC 61754-13[6]	Datacom, telecom, measurement equipment, single-mode lasers[9]	[upper-alpha 1][upper-alpha 2]
Fibergate		Snap, with dust-cap	n/a	1.25 mm		Backplane connector
FJ	Fiber-Jack[11] or Opti-Jack[7]	Snap (duplex)[1]	n/a	2.5 mm		Building wiring, wall outlets
LC	Lucent Connector,[7] Little Connector,[12] or Local Connector[12]	Snap	n/a	1.25 mm	IEC 61754-20[6]	High-density connections, SFP and SFP+ transceivers, XFP transceivers[9]	[upper-alpha 3]
Lucxis				1.25 mm	ARINC 801	PC (straight physical contact) or APC (angled physical contact) configurations
LX-5		Snap, with light- and dust-cap	n/a		IEC 61754-23	High-density connections; rarely used
M12-FO		Duplex screw	M16	2.5 mm	EN 61754-27, ISO/IEC 61754-27	Machine, process and plant engineering. IP-67 dust and water resistant
MIC	Media Interface Connector	Snap	n/a	2.5 mm		Fiber distributed data interface (FDDI)
MPO or MTP	Multiple-Fiber Push-On/Pull-off[7]	Snap (multiplex push-pull coupling)	n/a	2.5×6.4 mm[13]	IEC-61754-7;[6] EIA/TIA-604-5 (FOCIS 5)	SM or MM multi-fiber ribbon. Same ferrule as MT, but more easily reconnectable.[13] Used for indoor cabling and device interconnections. MTP is a brand name for an improved connector, which intermates with MPO.[14]	[upper-alpha 4]
MT	Mechanical Transfer	Snap (multiplex)[1]	n/a	2.5×6.4 mm		Pre-terminated cable assemblies; outdoor applications[13]
MT-RJ	Mechanical Transfer Registered Jack or Media Termination - recommended jack[7]	Snap (duplex)[1]	n/a	2.45×4.4 mm	IEC 61754-18	Duplex multimode connections	[upper-alpha 5]
MU	Miniature unit[7]	Snap	n/a	1.25 mm	IEC 61754-6	Common in Japan[1]
SC	Subscriber connector,[7] square connector[7] or standard connector	Snap (push-pull coupling)	n/a	2.5 mm	IEC 61754-4[6]	Datacom and telecom; GPON; EPON; GBIC; MADI	[upper-alpha 6][upper-alpha 3]
SC-DC/ SC-QC	SC-Dual Contact/ SC-Quattro Contact[11]	Snap (push-pull coupling; duplex)	n/a	2.5 mm	IEC 61754-4	Datacom and telecom; GPON; EPON; GBIC
SMA 905 F-SMA I	Sub Miniature A	Screw (also available as a keyed connector)	1/4"-36 UNS 2B	3.17 mm[16]	IEC 60874-2	Industrial lasers, optical spectrometers, military; telecom multimode	[upper-alpha 7]
SMA 906 F-SMA II	Sub Miniature A	Screw	1/4"-36 UNS 2B	Stepped; typ. 0.118 in (3.0 mm), then 0.089 in (2.3 mm)	IEC 60874-2	Industrial lasers, military; telecom multimode
SMC	Sub Miniature C	Snap	n/a	2.5 mm
ST or BFOC	Straight Tip[7] or Bayonet Fiber Optic Connector	Bayonet	n/a	2.5 mm	IEC 61754-2[6]	Datacom	[upper-alpha 8]
TOSLINK	Toshiba Link	Snap	n/a		most common is JIS F05	Digital audio
VF-45	Volition Fiber	Snap	n/a	None - V-grooves as guidance		Datacom
1053 HDTV	Broadcast connector interface	Push-pull coupling	n/a	Industry-standard 1.25 mm diameter ceramic ferrule		Audio & Data (broadcasting)
V-PIN	V-System	Snap (Duplex) Push-pull coupling	n/a			Industrial and electric utility networking; multimode 200 μm, 400 μm, 1 mm, 2.2 mm fibers

Notes

1. FC connectors' floating ferrule provides good mechanical isolation. FC connectors need to be mated more carefully than the push-pull types due to the need to align the key, and due to the risk of scratching the fiber end face while inserting the ferrule into the jack. An FC connector should not be used in vibrating environments due to its threaded lock. FC connectors have been replaced in many applications by SC and LC connectors.[1]
2. There are two incompatible standards for key widths on FC/APC and polarization-maintaining FC/PC connectors: 2 mm (reduced or type R) and 2.14 mm (NTT or type N).[10] Connectors and receptacles with different key widths either cannot be mated, or will not preserve the angle alignment between the fibers, which is especially important for polarization-maintaining fiber. Some manufacturers mark reduced keys with a single scribe mark on the key and mark NTT connectors with a double scribe mark.
3. LC connectors have replaced SC connectors in corporate networking environments due to their smaller size; they are often found on small form-factor pluggable transceivers.
4. MPO (Multi-fiber Push On) is a connector for ribbon cables with four to twenty-four fibers.[15] Connectors for single-mode fiber have angled ends to minimize back-reflection, while multimode fiber versions typically have flat ends. MTP is a brand name for a version of the MPO connector with improved specifications. MTP and MPO connectors intermate.
5. MT-RJ (Mechanical Transfer Registered Jack) uses a form factor and latch similar to the 8P8C (RJ45) connectors. Two separate fibers are included in one unified connector. It is easier to terminate and install than ST or SC connectors. The smaller size allows twice the port density on a face plate than ST or SC connectors do. The MT-RJ connector was designed by AMP, but was later standardized as FOCIS 12 (Fiber Optic Connector Intermateability Standards) in EIA/TIA-604-12. There are two variations: pinned and no-pin. The pinned variety, which has two small stainless steel guide pins on the face of the connector, is used in patch panels to mate with the no-pin connectors on MT-RJ patch cords.
6. The push-pull design on SC connectors reduces the chance of fiber end face contact damage during connection. These are frequently found on older networking gear using GBICs.
7. The SMA connector was the first widely used standard connector, developed in the 1970s by Amphenol using the design geometry of the SMA RF connector.[17] It was designed for large-diameter multimode fiber applications, for which it is still widely used in industry and medicine. It lacks features important to communications applications, for which it is considered obsolete.
8. ST connectors have a key which prevents rotation of the ceramic ferrule, and a bayonet lock similar to a BNC shell. The single index tab must be properly aligned with a slot on the mating receptacle before insertion; then the bayonet interlock can be engaged, by pushing and twisting, locking at the end of travel which maintains spring-loaded engagement force on the core optical junction.

Obsolete connectors

Obsolete fiber connector types

Short name	Long form	Coupling type	Screw thread	Ferrule diameter	Standard	Typical applications
Biconic[1]		Screw		2.5 mm
D4 (NEC)[1]		Screw		2.0 mm		Japanese telecom in the 1970s and 1980s
Deutsch 1000		Screw				Telecom
DIN (LSA)		Screw			IEC 61754-3[6]	Telecom in Germany in 1990s, measurement equipment
OPTIMATE		Screw				Plastic fiber
OptoClip II		Snap (push-pull coupling)	n/a	None - bare fiber used	Proprietary Hüber & Suhner	Datacom and telecom, last made in 2005

Contact

Modern connectors typically use a physical contact polish on the fiber and ferrule end. This is a slightly convex surface with the apex of the curve accurately centered on the fiber, so that when the connectors are mated the fiber cores come into direct contact with one another.[18][19] Some manufacturers have several grades of polish quality, for example a regular FC connector may be designated FC/PC (for physical contact), while FC/SPC and FC/UPC may denote super and ultra polish qualities, respectively. Higher grades of polish give less insertion loss and lower back reflection.

Many connectors are available with the fiber end face polished at an angle to prevent light that reflects from the interface from traveling back up the fiber. Because of the angle, the reflected light does not stay in the fiber core but instead leaks out into the cladding. Angle-polished connectors should only be mated to other angle-polished connectors. The APC angle is normally 8 degrees, however, SC/APC also exists as 9 degrees in some countries. Mating to a non-angle polished connector causes very high insertion loss. Generally angle-polished connectors have higher insertion loss than good quality straight physical contact ones. "Ultra" quality connectors may achieve comparable back reflection to an angled connector when connected, but an angled connection maintains low back reflection even when the output end of the fiber is disconnected.

Angle-polished connections are distinguished visibly by the use of a green strain relief boot, or a green connector body. The parts are typically identified by adding "/APC" (angled physical contact) to the name. For example, an angled FC connector may be designated FC/APC, or merely FCA. Non-angled versions may be denoted FC/PC or with specialized designations such as FC/UPC or FCU to denote an "ultra" quality polish on the fiber end face. Two different versions of FC/APC exist: FC/APC-N (NTT) and FC/APC-R (Reduced). An FC/APC-N connector key will not fit into a FC/APC-R adapter key slot.

Mnemonics

MT-RJ connectors look like a miniature RJ-45 connector.

ST connectors refer to having a straight tip, as the sides of the ceramic tip are parallel—as opposed to the predecessor bi-conic connector which aligned as two nesting ice cream cones would.

SC is short for subscriber connector.[7] SMA is short for subminiature assembly.

Field-mountable connectors

Field-mountable optical fiber connectors are used to join optical fiber jumper cables that contain one single-mode fiber. Field-mountable optical fiber connectors are used for field restoration work and to eliminate the need to stock jumper cords of various sizes.

These assemblies can be separated into two major categories: single-jointed connector assemblies and multiple-jointed connector assemblies. According to Telcordia GR-1081,[20] a single-jointed connector assembly is a connector assembly where there is only one spot where two different fibers are joined together. This is the situation generally found when connector assemblies are made from factory-assembled optical fiber connector plugs. A multiple-jointed connector assembly is a connector assembly where there is more than one closely spaced connection joining different fibers together. An example of a multiple-jointed connector assembly is a connector assembly that uses the stub-fiber type of connector plug.

Attributes

Features of good connector design:

• Low insertion loss
• High return loss (low amounts of reflection at the interface)
• Ease of installation
• Low cost
• Reliability
• Low environmental sensitivity
• Ease of use

Analysis

• In general, the insertion loss should not exceed 0.75 dB and the return loss should be higher than 20 dB. Typical insertion repeatability, the difference in insertion loss between one plugging and another, is 0.2 dB.
• On all connectors, cleaning the ceramic ferrule before each connection helps prevent scratches and extends the connector life substantially.
• Connectors on polarization-maintaining fiber are sometimes marked with a blue strain relief boot or connector body. Sometimes a blue buffer tube is used on the fiber instead.[21]
• Hardened Fiber Optic Connectors (HFOCs) and Hardened Fiber Optic Adapters (HFOAs) are passive telecommunications components used in an outside plant environment. They provide drop connections to customers from fiber distribution networks. These components may be provided in pedestal closures,[note 1][22] aerial and buried closures and terminals, or equipment located at customer premises such as a Fiber Distribution Hub (FDH) or an optical network terminal unit.

These connectors, which are field-mateable and hardened for use in the OSP, are needed to support Fiber to the Premises (FTTP) deployment and service offerings. HFOCs are designed to withstand climatic conditions existing throughout the U.S., including rain, flooding, snow, sleet, high winds, and ice and sand storms. Ambient temperatures ranging from −40 °C (−40 °F) to 70 °C (158 °F) can be encountered.

Telcordia GR-3120[23] contains the industry’s most recent generic requirements for HFOCs and HFOAs.

Testing

Glass fiber optic connector performance is affected both by the connector and by the glass fiber. Concentricity tolerances affect the fiber, fiber core, and connector body. The core optical index of refraction is also subject to variations. Stress in the polished fiber can cause excess return loss. The fiber can slide along its length in the connector. The shape of the connector tip may be incorrectly profiled during polishing. The connector manufacturer has little control over these factors, so in-service performance may well be below the manufacturer's specification.

Testing fiber optic connector assemblies falls into two general categories: factory testing and field testing.

Factory testing is sometimes statistical, for example, a process check. A profiling system may be used to ensure the overall polished shape is correct, and a good quality optical microscope to check for blemishes. Insertion loss and return loss performance is checked using specific reference conditions, against a reference-standard single-mode test lead, or using an encircled flux compliant source for multi-mode testing. Testing and rejection (yield) may represent a significant part of the overall manufacturing cost.

Field testing is usually simpler. A special hand-held optical microscope is used to check for dirt or blemishes. A power meter and light source or an optical loss test set (OLTS) is used to test end-to-end loss, and an optical time-domain reflectometer may be used to identify significant point losses or return losses.

Notes

1. Pedestal terminal closures are intended to house passive telecommunications components used in an Outside Plant (OSP) environment. According to Telcordia GR-13, these closures may house such components as copper terminal blocks, coaxial taps, or passive fiber optic distribution equipment used for the distribution of telephone service and broadband services.

See also

• Optical fiber cable – color coding of connector boot and fiber cable jackets
• Optical attenuator – fiber optic attenuator
• Gap loss – attenuation sources and causes
• Index-matching material –a liquid/gel to reduce Fresnel reflection

References

1. "Connector identifier". The Fiber Optic Association. 2010. Retrieved Oct 18, 2014.
2. Silva, Mário Marques da (2016-01-06). Cable and Wireless Networks: Theory and Practice. CRC Press. ISBN 9781498746830.
3. Alwayn, Vivek (2004). "Fiber-Optic Technologies". Retrieved Aug 15, 2011.
4. "DMI datasheet" (PDF). DIAMOND SA. Archived from the original (PDF) on 10 October 2014. Retrieved 6 Oct 2014.
5. "European Union Intellectual Property Office (EUIPO): Trade mark information E-2000". Retrieved 2019-12-08.
6. "The History of Connectors - AFL Hyperscale". AFL Hyperscale. Retrieved 2018-11-05.
7. Keiser, Gerd (August 2003). Optical Communications Essentials. McGraw-Hill Networking Professional. p. 132–. ISBN 0-07-141204-2.
8. TIA Standard FOCIS-4, TIA-604-4-B
9. "Fiber Optic Connectors". Archived from the original on March 12, 2016. Retrieved Oct 18, 2014.
10. Sezerman, Omur; Best, Garland (December 1997). "Accurate alignment preserves polarization" (PDF). Laser Focus World. Retrieved December 7, 2016.
11. "Small Form Factor Fiber Optic Connectors Tutorial". Fiberstore. June 3, 2014. Retrieved Oct 18, 2014.
12. US patent 20140126875, Lou Guzzo, Inman, SC (US), "Connector Ferrule Holder", issued 2014-05-08
13. Shimoji, Naoko; Yamakawa, Jun; Shiino, Masato (1999). "Development of Mini-MPO Connector" (PDF). Furukawa Review (18): 92.
14. "Frequently asked questions". US Conec. Archived from the original on 21 April 2009. Retrieved 12 Feb 2009.
15. "MTP/MPO Fiber Solution".
16. "Amphenol Fiber Optics products catalog, SMA standard definition, page 131-132" (PDF). Retrieved 2019-02-28.
17. Neal Weiss (July 7, 2016). "What is an SMA connector and why do we care?". Fiber Optic Center. Retrieved August 16, 2018.
18. "The Importance of Geometry for Fiber Optic Connectors" (pdf). Corning Cable Systems. April 2006.
19. Yin, Ling; Huang, H.; Chen, W.K.; Xiong, Z.; Liu, Y.C.; Teo, P.L. (May 2004). "Polishing of fiber optic connectors" (PDF). International Journal of Machine Tools and Manufacture. 44 (6): 659–668. doi:10.1016/j.ijmachtools.2003.10.029.
20. "GR-1081, Generic Requirements for Field-Mountable Optical Fiber Connectors". Telcordia.
21. "Polarization maintaining fiber patchcords and connectors" (pdf). OZ Optics. Retrieved Feb 6, 2009.
22. GR-13-CORE, Generic Requirements for Pedestal Terminal Closures, Telcordia.
23. GR-3120, Generic Requirements for Hardened Fiber Optic Connectors (HFOCs) and Hardened Fiber Optic Adapters (HOFAs), Telcordia.

External links

• Fiber Optic Connector Reference
• How To Terminate Fiber Optic Connectors
• Fiber optic connector termination processes
• SC Connector termination anaerobic processes (Video)