Hypersonic wind tunnel

A hypersonic wind tunnel is designed to generate a hypersonic flow field in the working section, thus simulating the typical flow features of this flow regime - including compression shocks and pronounced boundary layer effects, entropy layer and viscous interaction zones and most importantly high total temperatures of the flow. The speed of these tunnels vary from Mach 5 to 15. The power requirement of a wind tunnel increases with the cross section, the flow density and is directly proportional to the third power of the test velocity. Hence installation of a continuous, closed circuit wind tunnel remains a costly affair. The first continuous Mach 7-10 wind tunnel with 1x1 m test section was planned at Kochel am See, Germany during WW II[1] and finally put into operation as 'Tunnel A' in the late 1950s at AEDC Tullahoma, TN, USA for an installed power of 57 MW. In view of these high facility demands, also intermittently operated experimental facilities like blow-down wind tunnels are designed and installed to simulate the hypersonic flow. A hypersonic wind tunnel comprises in flow direction the main components: heater/cooler arrangements, dryer, convergent/divergent nozzle, test section, second throat and diffuser. A blow-down wind tunnel has a low vacuum reservoir at the back end, while a continuously operated, closed circuit wind tunnel has a high power compressor installation instead. Since the temperature drops with the expanding flow, the air inside the test section has the chance of becoming liquefied. For that reason, preheating is particularly critical (the nozzle may require cooling).

NASA Langley's Hypersonic Facilities Complex, 1969

Technological problems

There are several technological problems in designing and constructing a hyper-velocity wind tunnel:

  • supply of high temperatures and pressures for times long enough to perform a measurement
  • reproduction of equilibrium conditions
  • structural damage produced by overheating
  • fast instrumentation
  • power requirements to run the tunnel

Simulations of a flow at 5.5 km/s, 45 km altitude would require tunnel temperatures of over 9000 K, and a pressure of 3 GPa (see discussion).

Hot shot wind tunnel

One form of HWT is known as a Gun Tunnel or hot shot tunnel (up to M=27), which can be used for analysis of flows past ballistic missiles, space vehicles in atmospheric entry, and plasma physics or heat transfer at high temperatures. It runs intermittently, but has a very low running time (less than a second). The method of operation is based on a high temperature and pressurized gas (air or nitrogen) produced in an arc-chamber, and a near-vacuum in the remaining part of the tunnel. The arc-chamber can reach several MPa, while pressures in the vacuum chamber can be as low as 0.1 Pa. This means that the pressure ratios of these tunnels are in the order of 10 million. Also, the temperatures of the hot gas are up to 5000 K. The arc chamber is mounted in the gun barrel. The high pressure gas is separated from the vacuum by a diaphragm.

Prior to a test run commencing, a membrane separates the compressed air from the gun barrel breech. A rifle (or similar) is used to rupture the membrane. Compressed air rushes into the breech of the gun barrel, forcing a small projectile to accelerate rapidly down the barrel. Although the projectile is prevented from leaving the barrel, the air in front of the projectile emerges at hypersonic velocity into the working section. Naturally the duration of the test is extremely brief, so high speed instrumentation is required to get any meaningful data.

Hypersonic Wind Tunnel Facility in India

ISRO commissioned two major facilities — a Hypersonic Wind Tunnel and Shock Tunnel — at the Vikram Sarabhai Space Center as part of its continuous and concerted efforts to minimize cost of access to space. ISRO Chairman A. S. Kiran Kumar said commissioning of such facilities would provide adequate data for design and development of current and future space transportation systems in India.

MARHY, Hypersonic Wind Tunnel Facility in Orléans FRANCE
Photo of the wind tunnel MARHy

The MARHy Hypersonic low density Wind Tunnel, located at the ICARE[2] Laboratory in Orléans, France, is a research facility used extensively for fundamental and applied research of fluid dynamic phenomena in rarefied compressible flows, applied to space research(contact Viviana Lago: head of the Fast team, viviana.lago@cnrs-orleans.fr). Its name is an acronym for Mach Adaptable Rarefied Hypersonic and the wind tunnel is recorded under this name under the European portal MERIL.

gollark: https://www.fda.gov/drugs/development-approval-process-drugs/frequently-asked-questions-patents-and-exclusivity
gollark: > Patent terms are set by statute. Currently, the term of a new patent is 20 years from the date on which the application for the patent was filed in the United States. Many other factors can affect the duration of a patent.
gollark: Again, I'm pretty sure that is not how patents work.
gollark: If you change it slightly, you can patent the *new* thing, not the *old* one.
gollark: That... is not how patents work.

See also

References
  1. Eckardt, Dietrich: "The 1x1 m hypersonic wind tunnel Kochel/Tullahoma 1940-1960", CEAS Space Journal, March 2015, Vol. 7, Issue 1, pp. 23-36
  2. ICARE Laboratory, CNRS, Orléans
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.