Cromemco Bytesaver

The Bytesaver, introduced by Cromemco in 1976, was the first programmable memory board for the MITS Altair and S-100 bus microcomputer systems. The Bytesaver had sockets for 8 UV-erasable EPROMs providing up to 8 Kbytes of storage. The EPROMs could be programmed by the Bytesaver, or read as computer memory. In the history of microcomputer systems, the Bytesaver was the first viable alternative to the use of punched paper tape for storing programs, and has been called “a great advance in microcomputer technology”.[1]

Cromemco 8K Bytesaver (1976)

Background

The Altair 8800, which began the personal computer revolution, was introduced in January 1975 with no hardware or software support for floppy disk or hard disk storage. When Paul Allen travelled to the MITS factory in Albuquerque, New Mexico to demonstrate what would become Microsoft BASIC, he brought with him a punched paper tape of the code that he and Bill Gates had developed. According to Allen, the 7168 byte program took 7 minutes to load from a Teletype Model 33 paper tape reader.[2]

To reduce the time required to load software, and to support a more convenient storage medium than paper tape, Cromemco developed the first programmable solid-state storage system for the Altair microcomputer. Cromemco called it the "Bytesaver" and introduced it in the February 1976 issue of Byte magazine.[3] With the Bytesaver the time to load Microsoft 8K Basic was reduced from 7 minutes to less than one second.[4]

Technology
Intel 2708 EPROM installed in a Cromemco 8K Bytesaver S-100 Board

The Bytesaver used solid-state UV erasable EPROMS that provided up to 8K bytes of program or data storage. The original Bytesaver could support either the type 2704 or 2708 EPROM. The Bytesaver came with one 2704 EPROM containing a program called “Bytemover” to facilitate EPROM programming. The EPROMS to be programmed were selected from the front panel switches of the Altair computer.

A switch on the Bytesaver card was used to turn on or off the EPROM programming voltage. With this switch off there was no chance for accidental programming of the memory. Once programmed the information was retained in the EPROMS, but the memory chips could be erased by removing them from the Bytesaver and placing them under an ultraviolet light.

Cromemco also offered a 3K Control Basic interpreter, developed by Li-Chen Wang. This very compact Basic was supplied on three 2708 EPROMS that could plug into the Bytesaver.[5]

Product family
Cromemco 16KPR Memory Card (1977)

The original Bytesaver, introduced in 1976, was called the 8K Bytesaver since it could store up to 8K bytes of information using eight 2708 EPROMS. One limitation of early S-100 bus microcomputer systems was the 64 Kbyte address space. Cromemco introduced the concept of bank-switching to the S-100 bus which allowed memory to be place in one of 8 banks of 64 Kbytes, thus expanding the effective address space to 512 Kbytes.[6] The Bytesaver II succeeded the 8K Bytesaver in 1978, and supported memory bank switching.[7]

For applications that required a ROM memory card, but did not require the ability to program the EPROMS, Cromemco also introduced a 16K ROM card. This card was named the 16KPR and was introduced in 1977.[8]

When the 2716 EPROM was introduced, with twice the storage capacity of the 2708, Cromemco designed the 32K Bytesaver to support that chip. Unlike earlier Bytesavers that had 8 EPROM sockets, the 32K Bytesaver had 16 sockets to provide up to 32K bytes of programmable memory.[9]

Cromemco Bytesaver Product Family
ModelYear IntroducedEPROM typeProgrammerBank-switchingMaximum Capacity
8K Bytesaver19762704/2708yesno8 kB
16KPR19772704/2708noyes16 kB
Bytesaver II19782704/2708yesyes8 kB
32K Bytesaver19792716yesyes32 kB
gollark: I don't have mod powers.
gollark: Yes.
gollark: Yes, GTech™ actually uses infinite bases mostly.
gollark: Anyway, we are hoping that there will be no groups using ultraviolet/infrared/71TeV gamma rays in their flags until JPEG-XL comes out.
gollark: No.

References
  1. Veit, Stan (1993). "Cromemco: Innovation and Reliability". Stan Veit's History of the Personal Computer. Asheville, North Carolina: WorldComm. pp. 104–106. ISBN 1-56664-023-7. in 1976 it was a great advance in microcomputer technology
  2. Allen, Paul (2011). Idea Man : a memoir by the cofounder of Microsoft. New York: Penguin Group. p. 81. ISBN 978-1-59184-537-9. People grabbed coffee breaks while computers loaded paper tape in those days.
  3. Cromemco (February 1976). "Now a lower-priced and easy way to save your Altair 8800 programs". Byte Magazine. 0 (6): 31. Retrieved May 20, 2013.
  4. Hawkins, William J. (November 1977). "Plug-in circuits make home computers talk, listen, play music, and more". Popular Science. 211 (5): 91.
  5. "3K Control Basic Instruction Manual" (PDF). Cromemco. Archived from the original (PDF) on 2013-12-22. Retrieved 2013-02-18.
  6. Garland, Harry (1979). Introduction to Microprocessor System Design. New York: McGraw-Hill. p. 93. ISBN 0-07-022871-X. With memory bank select, memory is arranged in a number of separate banks of up to 64K each.
  7. Watzman, Barry. "Some Cromemco notes". retrotechnology.net. Retrieved May 20, 2013.
  8. "Cromemco 16K KPR ROM Board". S100Computers.com. Retrieved May 20, 2013.
  9. "Cromemco 32K Bytesaver Board". S100Computers.com. Retrieved May 20, 2013.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.