Armoured vehicle-launched bridge

An armoured vehicle-launched bridge (AVLB) [1] is a combat support vehicle, sometimes regarded as a subtype of military engineering vehicle, designed to assist militaries in rapidly deploying tanks and other armoured fighting vehicles across gap-type obstacles, such as (and primarily) rivers. The AVLB is usually a tracked vehicle converted from a tank chassis to carry a folding metal bridge instead of weapons. The AVLB's job is to allow armoured or infantry units to cross craters, anti-tank ditches, blown bridges, railroad cuts, canals, rivers and ravines[2]), when a river too deep for vehicles to wade through is reached, and no bridge is conveniently located (or sufficiently sturdy, a substantial concern when moving 60-ton tanks).

A Valentine bridgelayer of the 3rd Independent Bridge Building Company, Royal Armoured Corps, spans a damaged bridge near Meiktila, 28 March 1945.

The bridge layer unfolds and launches its cargo, providing a ready-made bridge across the obstacle in only minutes. Once the span has been put in place, the AVLB vehicle detaches from the bridge, and moves aside to allow traffic to pass. Once all of the vehicles have crossed, it crosses the bridge itself and reattaches to the bridge on the other side. It then retracts the span ready to move off again. A similar procedure can be employed to allow crossings of small chasms or similar obstructions. AVLBs can carry bridges of 60 feet (19 metres) or greater in length. By using a tank chassis, the bridge layer is able to cover the same terrain as main battle tanks, and the provision of armour allows them to operate even in the face of enemy fire. However, this is not a universal attribute: some exceptionally sturdy 6x6 or 8x8 truck chassis have lent themselves to bridge-layer applications.

External video
Video of FV4205 Chieftain Armoured Vehicle-Launched Bridge (AVLB) showing an AVLB in action and the various steps of laying the bridge

Origins
British Mark I tank at Cambrai.

The roots of the modern AVLB can be found in World War I, at the dawn of tank warfare. Having developed tanks, the United Kingdom and France were confronted with the problem of mounting tank advances in the face of the trenches that dominated the battlefields. Early engagements, such as at Cambrai demonstrated the tank's utility, but also highlighted its vulnerability to battlefield geography—many early tanks found themselves ignominiously stuck in the trenches, having insufficiently long tracks to cross them (as at right). To counter this disadvantage, tanks (especially the common British Heavy tanks) began to go into battle with fascines hanging over their bows, sometimes as simple as a bundle of heavy sticks. By dropping these into the trenches, they were able to create a wedge over which the tank could drive. Later, some tanks began to carry rails on their decks—the first AVLBs.

By 1919, the British Army had, at its training centre in Christchurch, a Mark V** tank with lifting gear able to carry and place a bridge or carry out mine clearing and demolition.[3]

World War II and subsequent use
A Churchill AVRE with Small Box Girder Bridge and Churchill Crocodile flame-throwing tank in 1945

It was in the World War II era that the importance of armoured bridge layers, as well as combat engineering vehicles and armoured recovery vehicles, became fully clear. With the advent of Blitzkrieg warfare, whole divisions had to advance along with tanks, which were suddenly far out-pacing the speed of infantry soldiers. Besides leading to the advent of self-propelled artillery/assault guns, mobile anti-aircraft and armoured personnel carriers/cars, it became clear that functions like vehicle repair, mine-clearing, and the like would have to be carried out by armoured vehicles advancing along with tanks. Moreover, these forces would have to be able to cross all forms of terrain without losing speed, and without having to concentrate their thrusts over certain bridges (and the rising weight of armoured vehicles meant that fewer and fewer bridges could support these massed crossings). The only feasible solution to the dilemma posed by the mobility of all-mechanised armed forces was a dedicated platform that could improvise river and obstacle crossings at short notice and in otherwise inconvenient locations. Tracked and armoured, it was capable of operating right alongside combat units, crossing rough terrain and advancing in the face of light fire. To maximize on common parts and ease maintenance complications, they were usually based on existing tank chassis.

Circa 1943, a Covenanter deploys its bridge.
Circa 2007, a Covenanter tank bridgelayer with bridge folded
Circa 2008, a Covenanter tank bridgelayer at the 1/15th Royal NSW Lancers awaiting restoration.
The Covenanter tank bridge-layer

One of the earliest series-produced examples is the Brückenleger IV, a German AVLB based on the Panzer IV, which entered service with the Wehrmacht in 1940. Twenty were built, but problems of excessive weight limited the vehicle's effectiveness, and eventually all 20 were converted back to tanks. A new scissors bridge design was brought out by the British in response to the war, sufficient to support a 24-ton load over 30 ft (9.1 m). This was developed for the Covenanter tank. Eventually, it developed into a 30-ton capacity and therefore was carried by a turretless Valentine tank. It was used in Italy, North West Europe and Burma.

The Allies developed similar equipment, mostly based on the ubiquitous Churchill infantry tank (carrying the Small Box Girder) and the Sherman medium tank of the British and U.S. armies, respectively. In some early designs, bridge-layers could emplace bridges, but not retract them. Other vehicles were integral to the bridge themselves (such as the Churchill Ark), wading to the middle of a river or driving up against an obstacle and extending simple ramps in both directions; following vehicles would drive directly over the bridge layer.

Modern

Most modern bridge layers are based on current main battle tank chassis.[4] An example of a modern main battle tank (MBT) chassis being converted to a bridgelayer is the creation of the M104 Wolverine Armored Bridgelayer. Based on a modified M1A2 SEP MBT chassis, the Wolverine replaces the MBT turret with a bridge fitted atop the chassis. The bridge atop the M104 Wolverine measures 26m in length, and taking just 4 minutes to place across an obstacle securely. The bridge is built to be able to withstand countless crossings of vehicles as heavy as the M1A2 Abrams, which weighs in at around 70 tonnes. Another approach to bridge laying across water is the use of amphibious vehicles which act as combination of pontoon and roadway. These enter the water and join together to form a bridge. An example is the German M3 Amphibious Rig, a bridging vehicle used by Germany, the UK, Singapore, and Taiwan.

Notable AVLBs in service
gollark: At this point I would probably quite like to go to a saner country in some years, but there are not really that many majority-english-speaking ones which also are good.
gollark: yeees, except *slightly* less insane.
gollark: I mean, yes, compared to third-world countries like... most African ones, or the US, we're doing okay.
gollark: No.
gollark: I mostly read my news in the afternoon, to prolong the suffering.

See also

References
  1. "Fatigue Life Prediction for Armoured Vehicle-Launched Bridge for MLC70 and MLC80 Loads". RDECOM. Retrieved 6 May 2013.
  2. "Armored Vehicle-Launched Bridge (AVLB)". Olive-Drab. Retrieved 6 May 2013.
  3. Tank, Mark V** (Female) (E1949.325)
  4. "ENGINEER AND COUNTERMINE EQUIPMENT" (PDF). AUSA.Org. Retrieved 6 May 2013.
  5. Titan Armoured Vehicle Launcher Bridge - British Army Website Archived 3 September 2011 at the Wayback Machine
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.