APAO

APAO is an acronym that stands for Amorphous (or Atactic) Poly Alpha Olefin(s). APAO is a commodity chemical used in multiple applications.

History

In the mid-to-late-1950s, atactic polypropylene was a by-product of the synthesis of isotactic polypropylene (iPP) using first and early second generation Ziegler-Natta (Z-N) catalysts, which typically produced about 10-15 wt% of APP. Polymerization reactions using those catalysts were based on solution processes that simplified the elimination of the APP due to solubility differences. In other processes, such as slurry or suspension, the APP had to be eliminated from the isotactic fraction by washing/extracting the polypropylene product with hydrocarbon solvents.

With the development in the 1980s of more active and stereospecific supported Z-N catalysts, the proportion of atactic polymer to crystalline isotactic polypropylene in the polymers produced was substantially reduced, to typically less than 2 or 3 wt%. Therefore, the polypropylene product generally did not require additional purification steps to remove the atactic or low crystalline fraction. This meant that the APP supply from polypropylene plants using standard first- and early second-generation Z-N catalysts decreased as commercial plants adopted the new catalysts. Little by-product APP was thereafter produced.

Because APP is a by-product, it frequently has broad product specifications . Starting in the late 1970s and the early 1980s, several chemical companies identified the need to have an APP-like polymer produced to tight specifications. This type of polyolefin became known as on-purpose APAO, or just APAO, or APO. APAO synthesis and manufacture has been accomplished by properly designing the process of synthesizing the amorphous polyolefin, specifically, by the proper choice of catalyst system and the use of olefinic co-monomers. This process results in products with defined properties, such as melt viscosity, softening point, needle penetration, open time and tensile strength.

Production

The amorphous polyalphaolefins are synthesized by a catalyst system based on a Z-N supported catalyst and an alkyl aluminum co-catalyst. The polymerization process produces a mostly amorphous polymer with low crystallinity. Crystallinity depends on the catalyst system and on the use of co-monomers.

Product types

The four distinctive commercially available product types of on-purpose APAO are:

  • Homopolymers of propylene
  • Copolymers of propylene and ethylene
  • Copolymers of propylene and 1-butene or other higher a-olefins
  • Terpolymers of ethylene, propylene and 1-butene

Properties

The composition of the APAO is typically determined by using infrared spectroscopy, specifically, FT IR.

Typical properties for APAO are:

  • Melt Viscosity (MV) - indicates processability and is typically determined at 375°F (190°C), as per the ASTM D-3236 or DIN 53019 test methods.
  • Needle Penetration (NP) - indicates resistance to deformation and hardness, and is typically determined as per ASTM D-1321, ASTM D5 or DIN EN 1426 test methods
  • Ring and Ball Softening Point (RBSP) - indicates resistance to heat, and is typically determined as per ASTM E-28 or DIN EN 1427 test methods.
  • Open Time (OT) - indicates how long it takes for a film of adhesive to set to a destructive bond. Typically determined as per ASTM D-4497.

Other tests carried out to determine product properties are:

  • Rheology- measured with a rheometer
  • Tensile strength and Modulus - measures mechanical properties - measured using a tensile tester
  • Molecular weight - used to obtain the molecular weight distribution, MWD, determined by Gel Permeation Chromatography, GPC
  • Shear Adhesion Failure Temperature (SAFT) Peel Adhesion Failure Temperature (PAFT)

Applications

Applications include:

  • Personal hygiene Baby diapers
  • Adult incontinence
  • Feminine hygiene
  • Paper and packaging
  • Paper lamination
  • Cardboard and case sealing
  • Pressure sensitive labels
  • Bookbinding
  • WoodworkingEdge banding
gollark: Completely beestructure the entire system!
gollark: Then the rules shall be editatteed.
gollark: Probably not, just add a rule talking about how the existing processing rules map to batch tasks.
gollark: What? No, probably not, you would just wait 150 minutes.
gollark: I mean more like being able to queue up batch operations on furnaces/mines or something, so you can say "process 10 clay into 10 brick" and your stuff will be busy for 150 minutes.

References
  • Pellon, B.J. and A. Sustic. 1991, TAPPI Hot Melt Symposium Notes. p.193
  • Pellon, B.J. and A. Sustic. 1991, Journal of The Adhesion and Sealant Council 20(2):41
  • Pellon, B.J. and A. Sustic. 1991, Adhesives Age, 34(12):17-20
  • Krishnamurthy, V. and A. Sustic. 1992. TAPPI Hot Melt Symposium Notes. p.77
  • Sustic, A. 1997, TAPPI Hot Melt Symposium Notes. p. 69
  • McLaughlin, K.W. and D.D. Latham. 1988. Polymer Preprints. ACS Division of Polymer Chemistry, 29(2):406
  • Pizzi, A. (Antonio), 1946- editor. Mittal, K. L., 1945- editor. Handbook of adhesive technology. ISBN 978-1-315-12094-2. OCLC 1016156120.CS1 maint: multiple names: authors list (link)
  • Krevelen, D. W. van (Dirk Willem) (1991). Properties of polymers : their estimation and correlation with chemical structure. Elsevier. ISBN 0-444-88160-3. OCLC 828158183.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.