Ethernet in the first mile

Ethernet in the first mile (EFM) refers to using one of the Ethernet family of computer network protocols between a telecommunications company and a customer's premises. From the customer's point of view it is their first mile, although from the access network's point of view it is known as the last mile. A working group of the Institute of Electrical and Electronics Engineers (IEEE) produced the standards known as IEEE 802.3ah-2004, which were later included in the overall standard IEEE 802.3-2008.

Although it is often used for businesses, it can also be known as Ethernet to the home (ETTH). One family of standards known as Ethernet passive optical network (EPON)) uses a passive optical network.

History

With wide, metro, and local area networks using various forms of Ethernet, the goal was to eliminate non-native transport such as Ethernet over Asynchronous Transfer Mode (ATM) from access networks.

One early effort was the EtherLoop technology invented at Nortel Networks in 1996, and then spun off into the company Elastic Networks in 1998.[1][2] Its principal inventor was Jack Terry. The hope was to combine the packet-based nature of Ethernet with the ability of digital subscriber line (DSL) technology to work over existing telephone access wires.[3] The name comes from local loop, which traditionally describes the wires from a telephone company office to a subscriber. The protocol was half-duplex with control from the provider side of the loop. It adapted to line conditions with a peak of 10 Mbit/s advertised, but 4-6 Mbit/s more typical, at a distance of about 12,000 feet (3,700 m). Symbol rates were 1 megabaud or 1.67 megabaud, with 2, 4, or 6 bits per symbol.[1] The EtherLoop product name was registered as a trademark in the US and Canada.[4] The EtherLoop technology was eventually purchased by Paradyne Networks in 2002,[5] which was in turn purchased by Zhone Technologies in 2005.[6]

Another effort was the concept promoted by Michael Silverton of using Ethernet variants that used fiber optic communication to residential as well as business customers. This was an example of what has become known as fiber to the home (FTTH). The Fiberhood Networks company provided this service from 1999 to 2001.[7][8]

Some early products around the year 2000, were marketed as 10BaseS by Infineon Technologies, although they did not technically use baseband signalling, but rather passband as in very-high-bit-rate digital subscriber line (VDSL) technology.[9] A patent was filed in 1997 by Peleg Shimon, Porat Boaz, Noam Alroy, Rubinstain Avinoam and Sfadya Yackow.[10] Long Reach Ethernet was the product name used by Cisco Systems starting in 2001.[11] It supported modes of 5 Mbit/s, 10 Mbit/s, and 15 Mbit/s depending on distance.[12][13]

In October 2000 Howard Frazier issued a call for interest on "Ethernet in the Last Mile".[14] At the November 2000 meeting, IEEE 802.3 created the "Ethernet in the First Mile" study group, and on July 16, 2001 the 802.3ah working group. In parallel participating vendors formed the Ethernet in the First Mile Alliance (EFMA) in December 2001 to promote Ethernet subscriber access technology and support the IEEE standard efforts.[15] At an early meeting, the EtherLoop technology was called 100BASE-CU and another technology called EoVDSL for Ethernet over VDSL.[16]

The working group's EFM standard was approved on June 24, 2004 and published on September 7, 2004 as IEEE 802.3ah-2004. In 2005 it was included into the base IEEE 802.3 standard. In 2005, the EFMA was absorbed by the Metro Ethernet Forum.[17]

In early 2006, work began on an even higher-speed 10 gigabit/second Ethernet passive optical network (10G-EPON) standard, ratified in 2009 as IEEE 802.3av.[18] The work on the EPON was continued by the IEEE P802.3bk Extended EPON Task Force,[19] formed in March 2012. The major goals for this Task Force included adding support for PX30, PX40, PRX40, and PR40 power budget classes to both 1G-EPON and 10G-EPON. The 802.3bk amendment was approved by the IEEE-SA SB in August 2013 and published soon thereafter as the standard IEEE Std 802.3bk-2013.[20]

In November 2011, IEEE 802.3 began work on EPON Protocol over Coax (EPoC).

Description

EFM defines how Ethernet can be transmitted over new media types using new Ethernet physical layer (PHY) interfaces:

EFM also addresses other issues, required for mass deployment of Ethernet services, such as operations, administration, and management (OA&M)[22] and compatibility with existing technologies (such as plain old telephone service spectral compatibility for copper twisted pair).

Copper wires
  • 2BASE-TL -- defined in clauses 61 and 63. Full-duplex long-reach point-to-point link over voice-grade copper wiring. 2BASE-TL PHY can deliver a minimum of 2 Mbit/s and a maximum of 5.69 Mbit/s over distances of up to 2700 m (9,000 ft), using ITU-T G.991.2 (G.SHDSL.bis) technology over a single copper pair.
  • 10PASS-TS -- defined in clauses 61 and 62. Full-duplex short-reach point-to-point link over voice-grade copper wiring. 10PASS-TS PHY can deliver a minimum of 10 Mbit/s over distances of up to 750 m (2460 ft), using ITU G.993.1 (VDSL) technology over a single copper pair.

Active fiber optics
  • 100BASE-LX10 defined in clause 58, providing point-to-point 100 Mbit/s Ethernet links over a pair of single-mode fibers up to at least 10 km.
  • 100BASE-BX10 defined in clause 58, providing point-to-point 100 Mbit/s Ethernet links over an individual single-mode fiber up to at least 10 km.
  • 1000BASE-LX10 defined in clause 59, providing point-to-point 1000 Mbit/s Ethernet links over a pair of single-mode fibers up to at least 10 km.
  • 1000BASE-BX10 defined in clause 59, providing point-to-point 1000 Mbit/s Ethernet links over an individual single-mode fiber up to at least 10 km.

Passive optical network

Fiber to the home can use a passive optical network.[23]

  • 1000BASE-PX10 defined in Clause 60 (added by IEEE Std 802.3ah-2004), providing P2MP 1000 Mbit/s Ethernet links over PONs, at the distance of at least 10 km, at the split of at least 1:16.
  • 1000BASE-PX20 defined in Clause 60 (added by IEEE Std 802.3ah-2004), providing P2MP 1000 Mbit/s Ethernet links over PONs, at the distance of at least 20 km, at the split of at least 1:16.
  • 1000BASE-PX30 defined in Clause 60 (added by IEEE Std 802.3bk-2013), providing P2MP 1000 Mbit/s Ethernet links over PONs, at the distance of at least 20 km, at the split of at least 1:32.
  • 1000BASE-PX40 defined in Clause 60 (added by IEEE Std 802.3bk-2013), providing P2MP 1000 Mbit/s Ethernet links over PONs, at the distance of at least 20 km, at the split of at least 1:64.

Additionally clause 57 defines link-level OA&M, including discovery, link monitoring, remote fault indication, loopbacks, and variable access.

2BASE-TL

2BASE-TL is an IEEE 802.3-2008 Physical Layer (PHY) specification for a full-duplex long-reach point-to-point Ethernet link over voice-grade copper wiring.[24][25]

Rates and distances

Unlike 10BASE-T, 100BASE-T and 1000BASE-T PHYs, providing a single rate of 10, 100, or 1000 Mbit/s respectively, 2BASE-TL link rate can vary, depending on the copper media characteristics (such as length, wire diameter or gauge, number of pairs if the link is aggregated, amount of crosstalk between the pairs, etc.), desired link parameters (such as desired SNR margin, Power Back-Off, etc.), and regional spectral limitations.

2BASE-TL PHYs deliver a minimum of 2 Mbit/s over distances of up to 2.7 kilometres (8,900 ft), using ITU-T G.991.2 (G.SHDSL.bis) technology over a single copper pair. These PHYs may also support an optional aggregation or bonding of multiple copper pairs, called PME Aggregation Function (PAF).

For a single pair, the minimum possible link bitrate is 192 kbit/s (3 x 64 kbit/s) and the maximum bitrate is 5.7 Mbit/s (89 x 64 kbit/s). On a 0.5 mm wire with 3 dB noise margin and no spectral limitations, the max bitrate can be achieved over distances of up to 1 kilometre (3,300 ft). At 6 kilometres (20,000 ft) the max achievable bitrate is about 850 kbit/s.

The throughput of a 2BASE-TL link is lower than the link's bitrate by an average 5%, due to 64/65-octet encoding and PAF overhead, both factors depend on packet size.[26]

10PASS-TS

10PASS-TS is an IEEE 802.3-2008 Physical Layer (PHY) specification for a full-duplex short reach point-to-point Ethernet link over voice-grade copper wiring.

10PASS-TS PHYs deliver a minimum of 10 Mbit/s over distances of up to 750 metres (2,460 ft), using ITU-T G.993.1 (VDSL) technology over a single copper pair. These PHYs may also support an optional aggregation or bonding of multiple copper pairs, called PME Aggregation Function (PAF).

Details

Unlike other Ethernet physical layers that provide a single rate such as 10, 100, or 1000 Mbit/s, 10PASS-TS link rate can vary, similar to 2BASE-TL, depending on the copper channel characteristics, such as length, wire diameter (gauge), wiring quality, the number of pairs if the link is aggregated and other factors.

VDSL is a short range technology designed to provide broadband over distances less than 1 km of voice-grade copper twisted pair line, but connection data rates deteriorate quickly as the line distance increases. This has led to VDSL being referred to as a "fiber to the curb" technology, because it requires fiber backhaul to connect with a carrier network over greater distances.

VDSL Ethernet in the first mile services using may be a useful way to standardise functionality on Metro Ethernet networks, or potentially to distribute internet access services over voice-grade wiring in multi-dwelling unit buildings. However, VDSL2 has already proven to be a versatile and faster standard with greater reach than VDSL.

gollark: For example, if the US government looks bad because unemployment is up 10 million, they can just buy 10 million employment from, say, Saudi Arabia, which has unelected leaders who don't really care, and their unemployment looks fine!
gollark: It makes sense, if you think about it. Some countries have lots of money and want to optimize for good-looking statistics. Some need money and don't really care what their unemployment figure is.
gollark: That would be unethical.
gollark: But nobody is actually forced to work anywhere else, that would be unethical.
gollark: If one country sells 10 million employment, their unemployment goes up by 10 million and whoever buys it has a 10 million reduction in unemployment.

See also

References
  1. Patrick H. Stanley (January 8, 2001). "Robust Ethernet in the First Mile" (PDF). Elastic Networks, Inc. Retrieved August 15, 2011.
  2. Laura Kujubu (April 6, 1998). "Nortel forms EtherLoop group". InfoWorld. p. 46. Retrieved August 15, 2011.
  3. Bob Metcalfe (March 9, 1998). "Nortel combines best of DSL with best of Ethernet for 10Mbps Internet access". InfoWorld. p. 139. Retrieved August 15, 2011.
  4. "EtherLoop, Serial Number: 75560747". US Patent and Trademark office. September 28, 1998. Retrieved August 15, 2011.
  5. "Paradyne Gets Elastic". Light Reading news release. December 28, 2001. Retrieved August 15, 2011.
  6. "Elastic Networks Elite Modem Installation Guide" (PDF). Elastic Networks, Inc. November 1999. Retrieved August 15, 2011.
  7. "Fiberhood Networks". company web site. Archived from the original on September 22, 2001. Retrieved August 16, 2011.
  8. Michael Silverton (March 3, 2001). "Ethernet in the first mile" (PDF). Retrieved August 16, 2011.
  9. "Infineon's Octal-10BaseS Ethernet over QAM-VDSL Selected by Telson I&C to Enable Broadband Access in Nationwide Korean MTU/MDU Deployment". News release. Infineon Technologies AG. July 2, 2002. Archived from the original on April 13, 2014. Retrieved August 27, 2011.
  10. "Infineon Strengthens Leadership in MDU/MTU Market with Ethernet over VDSL Technology Patent Award". News release. Infineon Technologies AG. January 8, 2001. Archived from the original on April 13, 2001. Retrieved August 27, 2011.
  11. "Infineon Announces Second Quarter Results". News release. Infineon Technologies. April 24, 2001. Retrieved August 28, 2011. ...strategic design-win with Cisco for new long range Ethernet products incorporating Infineon?'s 10BaseS? technology
  12. "Cisco Long-Reach Ethernet Solution" (PDF). Cisco Systems, Inc. May 22, 2002. Retrieved August 27, 2011.
  13. James Evans (February 20, 2001). "Cisco Offers New Long-Reach Ethernet: No new wiring needed; system uses existing phone lines". PC World. Archived from the original on January 20, 2010. Retrieved August 28, 2011.
  14. Howard Frazier (October 12, 2000). ""Ethernet in the Last Mile" Call for Interest". IEEE 802.3. Retrieved August 6, 2011.
  15. "Extreme Launches Ethernet Alliance". Light Reading news release. December 11, 2001. Retrieved August 15, 2011.
  16. Hugh Barrass (July 9, 2001). "EFM Copper Objective" (PDF). IEEE 802.3. Retrieved August 28, 2011.
  17. "MEF Absorbs EFMA". Light Reading news release. March 8, 2005. Retrieved August 15, 2011.
  18. "10Gb/s Ethernet Passive Optical Network". official working group web site. IEEE 802. Retrieved August 6, 2011.
  19. "IEEE P802.3bk Extended EPON Task Force".
  20. IEEE Std 802.3bk-2013, IEEE Standard for Ethernet - Amendment 1: Physical Layer Specifications and Management Parameters for Extended Ethernet Passive Optical Networks. IEEE. 2013.
  21. Gerry Pesavento (July 9, 2001). "Point to Multipoint Ethernet Passive Optical Network (EPON)" (PDF). IEEE 802.3. Retrieved August 28, 2011.
  22. Yaakov (Jonathan) Stein (2006). "Ethernet OAM" (pdf). White paper. RAD Data Communications Ltd. Retrieved August 6, 2011.
  23. "FTTH Council - Definition of Terms" (PDF). FTTH Council. January 9, 2009. Archived from the original (PDF) on September 24, 2017. Retrieved September 1, 2011.
  24. IEEE 802.3ah - Ethernet in the First Mile Task Force archive
  25. "Metro Ethernet Forum". Archived from the original on 2014-04-10. Retrieved 2014-04-17.
  26. Implementation and Applications of DSL Technology (book), Auerbach Publications 2008, ISBN 0-8493-3423-3, Table 13.6.

Further reading
  • Beck, Michael (2005). Ethernet in the First Mile: The IEEE802.3ah EFM Standard. McGraw-Hill Professional. ISBN 978-0-07-145506-0.
  • Wael Diab; Howard M. Frazier (2006). Ethernet in the First Mile: Access for Everyone. IEEE Standards Information Network. ISBN 9780738148380.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.