1
2
Is it a good practice to ignore IDNF errors in smart logs if no other evidence of problems (including smart self test and badblocks run) has been found? Does anyone have a experience with this? The details follows.
During checks to see if a 2 year old drive is still fine (for my notebook), and I noticed the following errors in smart log (excerpt from smartctl -a /dev/sdd):
SMART Error Log Version: 1
ATA Error Count: 33 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 33 occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 00 00 00 00 00 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 00 00 00 00 a0 00 00:05:34.511 IDENTIFY PACKET DEVICE
25 00 00 00 00 00 e0 ff 00:05:34.500 READ DMA EXT
25 00 01 00 00 00 e0 00 00:05:30.790 READ DMA EXT
25 00 01 00 00 00 e0 00 00:05:29.550 READ DMA EXT
25 00 01 00 00 00 e0 00 00:05:29.549 READ DMA EXT
Error 32 occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 32 9c fd ff 0f Error: IDNF 50 sectors at LBA = 0x0ffffd9c = 268434844
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 32 9c fd ff e0 00 00:00:51.163 READ DMA EXT
25 00 32 9c fd ff 0f 04 00:00:51.156 READ DMA EXT
25 00 32 9c fd ff e0 00 00:00:51.074 READ DMA EXT
25 00 32 9c fd ff 0f 04 00:00:51.068 READ DMA EXT
25 00 32 9c fd ff e0 00 00:00:50.985 READ DMA EXT
All remaining 3 errors stored in smart log are the same as the last one (IDNF error at 0x0ffffd9c).
As I understand it, the error means sector ID not found, so it does not directly mean that the drive is bad, but it's still fishy.
No smart attributes shows problems (eg. no reallocated sectors):
# smartctl --attributes /dev/sdd
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.13.10-200.fc20.i686] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 217 217 033 Pre-fail Always - 1
4 Start_Stop_Count 0x0012 099 099 000 Old_age Always - 1659
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 3856
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1659
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 29
193 Load_Cycle_Count 0x0012 056 056 000 Old_age Always - 441546
194 Temperature_Celsius 0x0002 206 206 000 Old_age Always - 29 (Min/Max 14/46)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
Also smart selftest reports no problems:
# smartctl -t long /dev/sdd
... after a while ...
# smartctl -l selftest /dev/sdd
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.13.10-200.fc20.i686] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 3853 -
# 2 Extended offline Completed without error 00% 3851 -
# 3 Short offline Completed without error 00% 3847 -
And just to be sure, I run badblocks overwriting the whole disk with random data to check if there are some bad sectors. And no problems found either:
# badblocks -s -w -v -t random /dev/sdd
Checking for bad blocks in read-write mode
From block 0 to 312571223
Testing with random pattern: done
Reading and comparing: done
Pass completed, 0 bad blocks found. (0/0/0 errors)
marbu
Posted 2014-04-27T15:48:07.603
Reputation: 173
Did you get a solution for this? Did you try to change cable and power supply? – JohnnyFromBF – 2014-07-28T08:18:14.973
I moved mentioned HDD from one computer into another as a replacement (so I changed both cable and power supply by doing this :) and during the transition process I wanted to make sure the drive is still ok. And the smart error shown above was the only indication that something may be wrong. Now I'm using it for few months and I haven't seen any other error so far. – marbu – 2014-07-28T18:27:52.537