Introduction

Do you want to change out your RAM on your iMac, but don't want to spend more time, or risk getting shocked by the Power Supply? This is an easer way to Replace or upgrade the RAM in your iMac without removing the Logic Board or the Power Supply. You may want prior experience upgrading RAM for this.

  1. APiXVT4PIRhrfkbf
    APiXVT4PIRhrfkbf
    EGywusYCDsmWLohv
    • The first step to getting into the iMac is to open the display. To do this, insert a iMac opining tool or an iFixit Opining Pick into the bottom left of the iMac, right above the chin.

  2. ysrPsmROUgY32gGa
    ysrPsmROUgY32gGa
    LxAKYhuKTZaDmZgd
    • The next step to getting the screen off is to slide the pick around the screen. Move the iFixit oping pick around the display, and be very carefull around the edges; you could break the glass.

  3. er4pSRVQfkXvSaHF
    er4pSRVQfkXvSaHF
    HtsakVN5Avi1gPuA
    GEGKhedjWZLnIYV6
    • Once you have slid the opening tool around the iMac, get a Plastic card, then slide that around the display, and finally, use the cards to pull out on the display, and open it to about 4"

  4. cr4rPfVFZA1y1HKP
    cr4rPfVFZA1y1HKP
    cpN322ZmuaJRKHTx
    • Next, open the display wide enough to fit your hand or a spudger inside, and disconnect the Display Power Cable.

  5. 1LO2cdyrZVgVVW21
    1LO2cdyrZVgVVW21
    56pOQcRaLm3Om4ME
    gYHvDan641NO3HlT
    • Use a spudger or your hand to disconnect the Display Data Cable.

  6. YPLwLAbaAoDcMflF
    YPLwLAbaAoDcMflF
    VFcu5OfVxmxMRWI6
    • Pull the display off the iMac, and use an Oping pick to remove the adhesive off the bottom of the iMac screen. Then it should be able to come right off. Set the display somewhere safe.

  7. xfANZdnQVjYQQonQ
    xfANZdnQVjYQQonQ
    FQTfxOlxrPVJRKmG
    • Disconnect the fan cable from the Logic Board.

  8. BXuT6VcX33aeoNeN
    BXuT6VcX33aeoNeN
    Um2LvoQWhfjaFfTv
    ZdIqvxYoC2oO6Grw
    • Unscrew the 3 T10 screws from the fan, and pull it gently out of the iMac.

  9. TuNLZyqyMaRMFeqX
    TuNLZyqyMaRMFeqX
    1qC3BaYjokOomlSI
    f2uSXwSYnOksCuB5
    • Detach the iSight camera cable from the iMac Logic Board.

    • Use your fingers or a Spudger to pull out the RAM retaining clips. This step is a lot harder.

    • Remove the first RAM module from their socket.

    • Use a Spudger or your fingers to pull out the last RAM module.

    • Insert your new RAM by putting it into the socket and pushing down, until you hear a click

Conclusion

To reassemble your device, Reattach the screen, and make sure to connect the cables.

Ottobunny

Member since: 15/12/22

605 Reputation

0 comments