Introduction

Suspension springs maintain your washing machine's stability similar to automotive shock absorbers. If damaged, faulty, or worn-out, your appliance will vibrate or shake more than usual. If you need to replace your Whirlpool WTW4800XQ2’s suspension springs, this guide will show you how to replace them. You can buy this component in home improvement stores, or through online shops such as Amazon.

Please do note that this guide may not work on other washing machine models. Also be sure to unplug your machine from the outlet before starting this guide.

  1. I5OFXYPsf6kthBCI
    • Disconnect the electrical cord from the power outlet.

  2. HNOtHRaGJLShWWXB
    HNOtHRaGJLShWWXB
    dW65eVpFkTLHrmrR
    • Turn the water hose fitting counterclockwise to unplug it from the machine.

    • Make sure you clean any water spillage to avoid electrical shock or a fall during reassembly.

  3. xnEDgbFt6CY1E1Ei
    xnEDgbFt6CY1E1Ei
    HpCBrE6ZSLmIDfPC
    • Use an 1/4 inch nut driver to remove the four 9.5 mm hex screws on the back of the machine that secure the upper machine loading lid and console.

  4. KaEco2pjFc3LIqnB
    • Remove the two brackets on the back by tilting them slightly upwards and then outwards.

  5. B5H2hUWs2u3A5fH3
    B5H2hUWs2u3A5fH3
    2Od5CAWSkSKRZAYx
    NKGBbVvmAPBPUnlF
    • Remove the 9.5 mm hex screw securing the console wiring cover with an 1/4 inch nut driver.

    • Remove the wiring cover by opening by and sliding it out.

  6. 5b2iWMJuhuxPsacc
    5b2iWMJuhuxPsacc
    oGdVRlDCfnuBoQrj
    • Gently pull the upper machine loading lid towards you to the to release the front latch mechanism.

  7. aFp5qTEOyqB34UKk
    aFp5qTEOyqB34UKk
    ALgQXLVJAAdqfJV4
    • Lift the loading lid off the machine and set it down gently in a secure place.

  8. gIPIfW1vKQ1XiMUr
    gIPIfW1vKQ1XiMUr
    IwLvF6hArqD5KsiF
    spnTcCGjeFbFUVWH
    • Hold the corner suspension spring (inside the machine) and lift it to release the end plastic joint.

    • Once the joint is in the air, rotate counterclockwise and push down to release the rod from the joint lock mechanism.

  9. TTSGyoHVCHovdeuk
    TTSGyoHVCHovdeuk
    dYtAxTKBbjCKmsSC
    ugCGwVymbsHVDngb
    • Lift the corner of the machine and remove the rod from the bottom of the machine.

    • Install the new rod while it's lifted up, and make sure it goes through the provided washing drum eyelid.

    • Lower the machine slowly.

  10. n4y6lNbVhGtPExMI
    n4y6lNbVhGtPExMI
    Nlx2uD3BTJXnuIjp
    LZBJExeyYcWeALQ1
    • Lift the rod and pass it through the upper joint bushing hole to secure.

    • Insert the rod through the suspension joint and make sure it locks in the correct slot.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Isabel Velázquez Vélez

Member since: 18/03/22

205 Reputation

2 comments

Es mas fácil acostar la lavadora hacia un lado

kelvin mantilla -

Yes, it's much better to set the washer on its side. There is a plastic bushing at the bottom of the washer that can be removed by pressing the locking tabs with your fingers and then the spring rod can be removed and replaced easily.

Ylberto Ruiz -