Introduction

Some things to consider before you work on the Sony Cyber-shot DSC W800 to replace the Motherboard:

  • The Motherboard is an integral part of the device and any improper handling can cause issues in other parts of the camera.
  • Be cautious when removing ribbon wires.
  • Be sure to keep track of all pieces that are taken apart.
  1. GUpTQtwboDrXYMtm
    GUpTQtwboDrXYMtm
    6JWdBUKJNLKdTRcU
    lUfZpSNNexmO1f6T
    • Remove the five 4.0 mm Phillips #000 screws on the back panel.

  2. outaTM3MNyES5oSc
    outaTM3MNyES5oSc
    c2jbyUXMKFHrOoVr
    • Using the Spudger, remove the back panel from the device.

    • The loose piece circled in the picture will most likely fall off the camera housing.

  3. NOEynXhFVV3QPweD
    NOEynXhFVV3QPweD
    lIJhSDlqMRpkTHcd
    vVLNlgUj1FpBeUZh
    • Remove the two 2.15mm Phillips #000 screws from the circuit board.

    • Gently pull on the ribbon wire from ZIF connector with the tweezers to remove the button board.

    • Ribbon wires can easily be damaged.

  4. vovXEsjq5UljFZR4
    • Remove the four 3.75 mm Phillips #000 screws from the LCD back panel.

  5. rIvy3mqNYEgtwnOH
    • Lift the back panel and separate the LCD Screen by prying it up.

    • Remove the back panel.

  6. PX6lfORPLn2gNEkF
    PX6lfORPLn2gNEkF
    n4liU2PYyR6aY1es
    • Gently pull on the ribbon wire disconnecting from the ZIF connector (connecting the LCD screen to the motherboard) with the tweezers.

    • Ribbon wires can be easily damaged.

  7. xBmnKZMrXSO6oph1
    xBmnKZMrXSO6oph1
    gWCjBb1K44l62XXs
    • With plastic opening tool, gently pry loose the front panel.

    • Separate front panel from the camera housing.

  8. 2OLSAdrvmW4J2YHF
    2OLSAdrvmW4J2YHF
    QKPlAcFedFNOriAV
    O2VEKWfCyFBrU5ZO
    • Remove the lens housing by pushing it, from the front, through the housing and lifting it out.

    • Gently pull on the large ribbon wire (connecting the Lens housing to the motherboard via ZIF connector) with the tweezers.

    • Gently pull on the small ribbon wire (connecting the Lens housing to the motherboard) with the tweezers.

    • Be careful not to damage either of the ribbon wires.

  9. bOIu2d6iKi6NoZmJ
    • Remove the single 3.75 mm Phillips #000 screw from the base of the motherboard.

  10. HKJa22x2fCcXdB1W
    • Remove the two 3.5 mm Phillips #000 screws from the secondary board that is attached to the flash bulb.

  11. qfuoXDfNgtcDnOnQ
    qfuoXDfNgtcDnOnQ
    lB3Vlls1Y5aUcMgS
    jixywaunjW6HgbBg
    • Use the tweezers. Move the thick red cable, attached to the secondary board, outside of its place in the camera housing.

    • Gently pull on the red/black wire in order to free the photo lens cylinder from the housing.

    • Remove the secondary board from its position and move it upward, out of the way.

    • From this point on, do not damage the connection between the motherboard and the secondary board.

  12. NJyRDNHbQsgfSc6q
    NJyRDNHbQsgfSc6q
    VFAxDdjxmOhVwfPc
    • Using the tweezers, pull the indicator bulb out , freeing it from its position on the housing.

    • Thread the indicator bulb under and through the secondary boards position.

  13. GgK4LvaEAKPUVeOg
    GgK4LvaEAKPUVeOg
    4NJeUKYcmo2I2MPE
    ATDAfdALvq2XWEgB
    • Using the tweezers, remove the black/red speaker wire from camera housing.

    • Pry loose and remove the speaker from the camera housing.

    • The speaker is attached with adhesive and must be removed with the spudger and moderate force.

  14. Qa5FToKRXPJZTcoj
    Qa5FToKRXPJZTcoj
    YClL4JZXYshdQtX4
    • Using the spudger, remove the mini speaker from the housing.

  15. x2Ewtw1sDYTtLheb
    x2Ewtw1sDYTtLheb
    XIOUy1YKqXevKwQB
    XR6PG6aHOlZYYYoL
    • Pull up on the bottom-half of the motherboard, slightly removing it from its position in the housing.

    • With enough force, pull up on the top right of the motherboard, pulling it entirely from its position in the housing.

    • Once again, be sure to keep the motherboard and secondary board connection intact.

  16. jOuJJPEGRCwoPfIG
    • Once apart, completely separate motherboard from the housing.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Thomas Campo

Member since: 09/02/16

788 Reputation

0 comments