Introduction

  1. bbmlHeqJ2AcAAfZC
    bbmlHeqJ2AcAAfZC
    uWuPnSoENURFjnXJ
    • Remove battery and card

  2. SFY2y4bIcFaEHkCg
    SFY2y4bIcFaEHkCg
    SprAdAZHqPXUxXSv
    GD34JjAKgADaMqeh
    • Right side, remove 1 M1.4x3.7 screw

    • Left side, remove 3 M1.4x3.7 screws

    • Bottom side, remove 5 M1.4x3.7 screws, including 2 in battery bay. 2 of them out of this photo, you can find them.

    • Do NOT touch screws on the bottom of LCD assembly.

  3. hGFMlxleZcJAGpBX
    • Pop the flash.

    • In flash room, remove 1 (one) M1.4x3.8 black screw.

  4. HkZhyWqijQoj4UNY
    HkZhyWqijQoj4UNY
    ebJLVB6oYdVcDHsP
    jfANQmLymrxIClEK
    • Remove LCD hinge cover, by sliding to the left.

    • Remove back cover, actually just a plastic frame.

  5. AXLdgtqhOpu4t5IZ
    AXLdgtqhOpu4t5IZ
    piNTK5EGJveScKpr
    • Remove 1 M1.4x2 screw

    • Remove another M1.4x2 screw, sorry for the angle.

  6. rlBMAbDYPTWAuXAn
    rlBMAbDYPTWAuXAn
    hIKIndM2Aj5RR36l
    2BjKPxUyAh21lsMW
    • CAUTION. Sony makes world's MOST BRITTLE FPC!

    • Loosen LCD assemble with caution!

    • Release FPC cable, the connector is flip type.

  7. D4gxMAohfcFPUDlH
    • The LCD assembly

  8. WM4YXYOq4AABXTRF
    WM4YXYOq4AABXTRF
    g5JFBv1biBELPr4w
    Dg6EEjyGJd2VTfcD
    • Remove 1 M1.4x2 screw

    • Lift the keypad.

    • Detach FPC

  9. AYpJ1QafgEIQXRmb
    • Remove 3 M1.4x3.6 black screws, 2 of them out of focus

  10. uUIFXLJExLQnu5Y6
    uUIFXLJExLQnu5Y6
    BdGiXTPBneMRsnFC
    • Slide the flash assembly backwards with caution.

    • Detach flash FPC by pulling it out of the socket.

    • High Voltage! Do NOT touch metal on FPC.

    • Then remove the flash assembly.

  11. LOTZCcXjgDpG4iHr
    • Remove that part whatever called, by sliding it backwards.

  12. 3lsqUf6G5h2WWaWj
    3lsqUf6G5h2WWaWj
    yLdnOSSbfJKKqIH1
    JQVNQeMTHQVPuZ1P
    • 1 ST1.7x5

    • 2 ST1.7x5

    • 1 M1.4x3.6 black

  13. e2BFKJJZbOqHahW2
    e2BFKJJZbOqHahW2
    iBTmCZtI36GPspQD
    • Remove 2 ST1.7x5 screws from inside the battery bay. (one of them not shown, deeper inside) insert screw driver through a hole in the shielding cover.

    • Pop the grip off. From back, push to the right, then it flies forward.

  14. bgJmmwaJNKbWNFfw
    • Remove 2 M1.4x2 black screws

  15. fWRWjVYpdVBJsThR
    fWRWjVYpdVBJsThR
    AS5KmZALPWNWv1IK
    • with caution and patient.

  16. DkTtftZWS1JTabRB
    DkTtftZWS1JTabRB
    uFIWJUPYxXTEGsLO
    jJVUvEWh5ZZFjl3r
    • 1 M1.4x3.6

  17. oBoHQCB3MoooiUbo
    • Sensor power, flip

    • Sensor signal, flip

    • Shutter, pull

    • Lens contacts, pull. Did I mention that Sony makes world's most brittle FPC?

    • Whatever, pull

    • Whatever, pull

    • Shutter charger motor FPC, (backside, pull out)

  18. wGDTbCbggFhsNMPK
    • Flip the Mainboard up

    • Pull out one more FPC

    • Discharge then desolder 4 wires.

    • CAUTION! Possible high DC voltage >300V

  19. ZJKHiHwAPNfXqsDn
    • Lift main board and plastic frame with flash capacitor.

  20. 5rCebElXP4m3lDel
    • Detach sensor Power (L)and Signal(R) FPC

  21. bo3uMxQ6ar16BIu4
    • Remove 3-4 ST1.7x5 screws

    • Remove 1 M1.4x5 screw

  22. KCvLlumsSdwTGBrD
    KCvLlumsSdwTGBrD
    hIHR1t2dfGHgpnZV
    • Remove 4 ST1.7x5 screws for the E-Mount

    • Remove mount metal ring

  23. TGTfPh22LjpOwXTs
    TGTfPh22LjpOwXTs
    JOi24IC5fSITZGKp
    O12yOgiVIvqQhTAi
    • Remove mount metal ring

    • Remove mount plastic ring

    • remove mount spring ring

  24. Fdn3HvHnGUVvGYXQ
    • Sensor + Shutter assembly comes off

  25. GpyRRQ3FQJKtnxDE
    • Separate sensor + shutter from another frame

  26. HCwOS3ABi3fIUqTn
    HCwOS3ABi3fIUqTn
    j14rajOTS6oRCDwO
    u3apPuLaZVAXnBWH
    • Remove 3 ST1.7x5 screws

    • Remove sensor shield / heat sink. Sensor PCBA might sticks to the shield, just separate them.

  27. sxXwWIXePYxyhMdn
    sxXwWIXePYxyhMdn
    DBOWTEUhEMTNvSkk
    • Remove sensor. the shutter assembly comes off.

    • Careful with 3 tiny spacers. Do NOT lose them.

  28. YOSuyE2GfWppheoO
    • Separate Shutter assembly form the mount body.

  29. qTKGSFuTw4VPml2H
    qTKGSFuTw4VPml2H
    2qHIkbAdvSbnAFPW
    RdFm1bMEiIbEuyxZ
    • Remove 1 screw (from the "Front" side)

    • Separate shutter curtain (Photo 3) from charging motor (not shown).

  30. RHGXe25LYhUcNcqT
    • Yes, replacing this little innocent part needs 3+ hours!

  31. aMeDfD2Yd5StQ6PQ
    • After removing the mount+shutter+sensor, it appears.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Terrance

Member since: 18/11/09

6359 Reputation

0 comments