Introduction

The battery is located inside the camera. It will require uninstalling the battery housing, illustrated in the guide below.

  1. QYAPnfNEvKb1LrTV
    • Remove the 5.00mm screw on the right of the LCD display towards the bottom of the device by using a Phillips #00 screwdriver.

    You also have to remove the screws at the bottom of the threaded stand mount hole, and inside the USB cover.

    Deen Hubin -

  2. aDHBBbVwSiVgLMqJ
    aDHBBbVwSiVgLMqJ
    ZtgEBoGPTCtcMJUd
    upPeWbNGkYRldUhE
    • Use the plastic opening tool to separate and remove the bottom red casing. Do this by, pushing the tool into the seam and prying up the red casing as you move along the edges.

    • Make sure to separate all the corners before removing the red casing.

  3. qimSZIDWFtUVa62O
    qimSZIDWFtUVa62O
    TDfiUWptwhQxLCsn
    • Using the plastic opening tool, separate and pull away the red casing on the right of the LCD screen.

    • Make sure to separate all the corners before removing the red casing.

    Also, remove the screw next to the SD card port before proceeding.

    Deen Hubin -

  4. LWZyrk3HkTJaCnyd
    LWZyrk3HkTJaCnyd
    NvFcwXu55IBKmdML
    • To access the HDMI slot, move slider towards the bottom of the casing on the other side of the camcorder. The lid casing will lift up upon doing so.

    • After accessing the HDMI slot you will find a 5.00mm screw. Using a Phillips #00 screwdriver, remove the screw.

  5. yDy4apJjnDYUWESe
    yDy4apJjnDYUWESe
    BUCMfhv4Gm5PAYkj
    • Using the plastic opening tool, separate and pull away the red casing to the left of the LCD screen.

    • Make sure to separate all the corners before removing the red casing.

  6. d64WmZGQaKnLuUHE
    d64WmZGQaKnLuUHE
    WZGxyhrgOcROWGGT
    • Remove the six 5.00mm screws by using a Phillips #00 screwdriver.

  7. tT4wC6nPLEJXrOQN
    tT4wC6nPLEJXrOQN
    AEFIEhiAIhAXdxiq
    FLsPoFERbsZdnC6u
    • Lift the two plastic tabs on the left side of the LCD screen and the single one on the right side on the black casing to open the device.

  8. SdG1Gw1gwc5Vvh33
    • Separate the front and back casing.

  9. yW1k2UZLQnIiDui6
    yW1k2UZLQnIiDui6
    ACkokUTslrGHxjiT
    • Remove the four 4.00mm screws holding the battery brace using a Phillips #00 screwdriver.

  10. eicTb6BGL5cxNvxs
    • Using a plastic opening tool, lift the copper tab holding the battery brace in place.

  11. GbJx2oH1AFtAVMUT
    GbJx2oH1AFtAVMUT
    5R2KOws4sAt1koo6
    • Remove the battery brace and battery from the camera casing.

    • Remove the old battery from the brace and place the new one.

    • Your battery might be held to the brace by a copper tape. If so, you'll need to peel the tape away to remove it. This tape does not affect the battery's operation in any way, so it is safe to remove it.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Ashton Esparza

Member since: 04/10/16

101 Reputation

0 comments