Samsung Galaxy A5 (2017) Motherboard Cover including NFC Antenna and Loudspeaker Replacement

Written By: Dominik Schnabelrauch
  • Comments: 2
Samsung Galaxy A5 (2017) Motherboard Cover including NFC Antenna and Loudspeaker Replacement

Difficulty

Moderate

Steps

6

Time Required

20 minutes

Introduction

Use this guide to remove the cover of the motherboard including the NFC antenna of your Samsung Galaxy A5 (2017) smartphone.

  1. UNT3BQFCLaKkOkBa

    • Power off your phone before beginning disassembly.

    • Use an iOpener to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes. You might want to repeat this step several times during the back cover removal.

    • The adhesive of the Samsung Galaxy A5 (2017) is very strong. A hair dryer, heat gun, or hot plate may also be used if you aren't able to open the device with the iOpener. Be careful not to overheat the phone—the AMOLED display and internal battery are both susceptible to heat damage.

  2. jmXFNCYJkWlJP1Er
    jmXFNCYJkWlJP1Er
    OvfoOcIZJyW2HvRW
    QO6sKv4HWRKe1RBr

    • Insert an opening pick at the bottom end of your phone.

    • If you can't manage to insert the opening pick between the back cover and the frame, you can use a suction handle to create a small gap.

    • Start to slide the tip of the opening pick to the bottom left corner and cut the adhesive with it.

    • Leave the opening pick in the bottom left corner to prevent the adhesive from resealing. Insert a new opening pick and start to cut the adhesive on the left side of the phone.

    Found it impossible to lift the back with out cracking the glass. However, once it was cracked and I didn’t care so much it was quicker to lie a hairdryer on it’s side and basically just peel the cover off (shattering the glass in multiple places). I’d recommend just factoring in a replacement back cover as part of replacing the screen, and then this step becomes a lot easier and less frustrating!

    David Barkhausen -

    Falls man den Jimmy besitzt, sollte man lieber diesen dafür benutzen. Dieser Schritt funktioniert damit wesentlich leichter als mit dem Plektrum.

    Philipp Schäfer -

  3. 3hRf5MEevtsN2l5S
    3hRf5MEevtsN2l5S
    EQmVdGujq6cYvuvX
    svDTKGLDGXraW6ig

    • Use an opening pick to cut the adhesive on all sides of the phone. Leave one opening pick in every corner to prevent the adhesive from resealing.

    • Reuse an iOpener if the adhesive becomes hard to cut. During the removal process the back cover is under tension all the time and is likely to break if the adhesive isn't loose enough.

    • Insert an opening pick on the right side of the phone after you cut the adhesive on all sides. Flip it sideways until you can get a good grip on the back cover.

  4. aIrV2oIrHptJIxnf

    • Remove the back cover from the phone.

    • Before applying new adhesive remove any remaining adhesive from the back cover and the frame and clean the areas with isopropyl alcohol and a lint-free cloth.

  5. KAwVROONLqbl114Y

    • Remove the eight Phillips #00 screws that hold the motherboard cover in its place.

  6. Ux3mKySApgEimXDn
    Ux3mKySApgEimXDn
    Tc2Lrm5NCpXct5EN
    kCoZajHRelXX1cl4

    • Use a pair of tweezers to lift the mother board cover on both upper corners of the phone out of its clamps.

    • Remove the motherboard cover including the NFC antenna and the loudspeaker.

Conclusion

To reassemble your device, follow these instructions in reverse order. When reassembling apply new adhesive where it's necessary.

Author

Dominik Schnabelrauch

Member since: 23/11/16

201132 Reputation

0 comments