Introduction

This guide will show you how to remove the motherboard so you can replace it.

  1. SJKZhwv5Q1kN2BiV
    • Move the switch on the battery door to the Open position.

    • The door will automatically swing open after you let it go.

  2. 3ZKsYoVItMVCPGWq
    3ZKsYoVItMVCPGWq
    XHScTkUwv5U2KKFg
    • Push the small gray tab on the top right corner to the left. The battery will pop out slightly.

    • Keep your finger clear of the battery when it pops out.

  3. MMZ2WGveTdsohiOf
    • Push the memory card in and let go.

    • The memory card will pop out slightly.

    • Pull out the memory card.

  4. vqO6xXrIFebmGlX3
    vqO6xXrIFebmGlX3
    tMJMAsJH3KmxEltC
    • Unscrew the small screws on the sides of the camera.

    • The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm).

  5. wjY555FG4V1uqISP
    wjY555FG4V1uqISP
    2YPpJAvFdj1tWDGB
    • Unscrew the three small screws on the bottom(#00P, 3.3mm).

    • The bottom will fall off.

  6. tsHbrJGmgDDRjpI2
    tsHbrJGmgDDRjpI2
    BQpHIUX3aohXG3lR
    WMVuJKPbJDuoSVSJ
    • Lift up the bottom back cover by prying the bottom edge with the spudger.

    • Gently lift up the back cover with your hand from the bottom to the top.

  7. vBpfLUMnqIboLRGL
    vBpfLUMnqIboLRGL
    FdxXLQkor6qMlYWR
    WsSyjuHAouCy2piE
    • Lift the tabs on the ZIF connectors.

    • The ribbon cables should easily come out of the ZIF connectors.

  8. QqEjD3X1swIb15jJ
    QqEjD3X1swIb15jJ
    dOIZiPDuuWsmA6pC
    • Using the spudger, pry off the top cover by gliding the spudger along the entire edge between the top cover and the front cover.

    • Be careful not to damage the cylindrical capacitor on the circuit board under the top cover.

  9. lZKVdhXcOhoHTGD3
    • Remove the small screw in the hole towards the top of the camera(#00P, 5.4mm).

  10. O2UErUOCGFGswIuT
    O2UErUOCGFGswIuT
    6DNQ6Xw2ZvEBR1sj
    • Use the spudger to lift up the back logic board.

    • Using your fingers, gently wiggle and pull off the back motherboard.

    • You will hear a click when you lift it up.

  11. uoZW2ZbtHaB1po6m
    • Remove the small screw holding down the lower motherboard(#00P, 3.2mm).

  12. mMiWmnSBMLCaNXMl
    mMiWmnSBMLCaNXMl
    j4C5PFc4pZUk4OW4
    GqbvvuKlnK1RuDor
    • Use the spudger to lift the upper tab from the main housing.

    • Gently lift the lower tab from the main body by prying it with your finger.

    • Gently pull off the plastic motherboard housing sideways.

  13. rMZlC2WKTanndUcW
    rMZlC2WKTanndUcW
    LnKG52Q6jEnFjDLv
    HrLo6AkYMYPuDAlk
    • Gently lift the tabs on the ZIF connectors connecting the lens to the front motherboard.

    • Once you lift the tabs the ribbons should fall right out and the front motherboard should be free.

    Sir we buy motherboard for this

    Adnan Khan -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Karissa

Member since: 13/04/12

50 Reputation

0 comments