Ninja Mega Kitchen System BL770 Circuit Board Replacement

Written By: Tommee Walker
  • Comments: 17
Ninja Mega Kitchen System BL770 Circuit Board Replacement

Difficulty

Moderate

Steps

5

Time Required

20 - 25 minutes

Introduction

In the chance that your circuit board stops working, this step-by-step guide will show you how to replace it. For soldering help, follow the How to Solder and Desolder Connections guide.

  1. JLqY1bSiWEmExw46
    JLqY1bSiWEmExw46
    OYEJIVAamIPcRN1S

    • Remove the five screws (13mm long, 6mm head) attaching the Base Cover using a Phillips screwdriver (Ph2).

    • Remove the two screws (13 mm long, 6mm head) attaching the Base Cover using a T10 screwdriver.

  2. SJWePFDgCtIKYmQB

    • Carefully remove the second layer from the base. You will not need a screwdriver for this step.

  3. WRAwfOqGoxRXUEEj
    WRAwfOqGoxRXUEEj
    ed1WJUCCSKCPdjmZ
    Whu1UiPQPE3svTXH

    • Remove the 2 screws (13mm, 6mm head) connected to the plastic piece holding down the power cord.

    • Then remove the additional 4 screws (13mm, 6mm head) and 2 screws (11mm, 5mm head) securing the base.

    • Carefully lift the base up from the rest of the blender.

  4. y2TUD22VPjCxOesu

    • Remove 4 screws (11mm, 4mm head) connecting the circuit board to the base.

    Where can I buy a new board?

    Forrest Lowe -

    Mein yeh circuit board kharidna chahta hoon kha se milega

    Pravjot Singh -

    Same question here

    Diego -

  5. BTvZ5DqOoTjcrprq
    BTvZ5DqOoTjcrprq
    4fYELAnl1ZHLRbIa

    • Cautiously desolder all the wires connecting the circuit board to the unit.

    • Carefully slide the circuit board free of the wires are place the new board in.

    • Solder the wires back onto the new board, keeping track of which wire goes where in order for your unit to properly function.

    Hi,

    I would like to know the specification of the metal oxyde varistor MOS as I need to change it.

    Thank you

    James -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Tommee Walker

Member since: 23/08/17

823 Reputation

13 comments

Thanks for the post… this is helping me with my blender…. by any chance do you have a better picture of the resistor on the back of the circuit board… it seems to be a yellow blue blue gold sequence resistor… my board just burned that resistor and I am trying to find and replace just that resistor if possible… but I am not sure of the colors so I can locate the right now.

Jose Gonzalez -

Does somebody know where can I buy this circuit board ??

castro_73 -

Anyone know the chip on this circuit board?? Proprietary I assume??

Nathan Walter -

Great info but i’m looking to purchase a replacement circuit board for my ninja blender and can not find one. Any ideas?

Rich -

hi,, i need to know the reference of transistor with position Q2. in the main board BL770 , thanks.

kolin camacho -

Hi, where did you buy this circuit board?

palmamail -

Hi, where do I find this circuit board please?

Daniel -

Hi Tom:

My BL770 turns the button on and off as soon as any button is pressed.  To turn it on again, it must be disconnected.  What could be the damage?  Thank you.

Jaime David -

Hi anyone know the reference of the varistor MOS on circuit board as I need to replace it.

Thanks !

James -

Hey, were you able to replace that varistor?

Amr -

Where can I buy the circuit board for the bl770 blender?

Idelf Roa -

Hello . Did you find the pcb anywhere?

orlando cortes -

Are you have pcb nijnja blender BL685.How much price??..

The Red Cool -