Logitech G502 Proteus Core Cable Replacement

Written By: Sen
  • Comments: 2
Logitech G502 Proteus Core Cable Replacement

Difficulty

Moderate

Steps

9

Time Required

20 minutes

Introduction

This guide shows how to replace the mouse cable for the Logitech G502 Proteus Core gaming mouse, whether it's due to a broken cable or to swap to a better paracord. It should be a relatively easy and quick repair and doesn't require any previous experience of fixing mice. Unplug your mouse before starting this repair.

  1. JkUFBTVXfFZZLpSG
    JkUFBTVXfFZZLpSG
    mdwCuHACyLXOiyiu

    • Use a hairdryer to heat three mouse feet briefly.

    • Each mouse foot should take 7-8 seconds to heat up.

  2. 2wLCZNr3et1pjhUS
    2wLCZNr3et1pjhUS
    EU1r4N4kHmLptdSF
    HYBpatSVRwDvI6C2

    • Remove the mouse feet gently.

    • Avoid bending the mouse feet.

  3. kCWHVeLZIdc4DAcw
    kCWHVeLZIdc4DAcw
    sNOZRmNSwx2sUHLy

    • Use a screwdriver to remove the four 12.5 mm screws.

  4. MdnCYHjucUBKZOTX
    MdnCYHjucUBKZOTX
    HNxgmdHoWomWC4yH
    mAvPGQGIbtIwHGEL

    • Use a spudger to pry open the bottom case.

    • A screwdriver is shown in the photo but screwdrivers shouldn't be used for prying. They might accidentally damage internal components with a slip.

  5. H4hihEn4O4HPBPcB
    H4hihEn4O4HPBPcB
    X6MEPwPsvKNfMVph

    • Raise the tabs to disconnect the ribbon.

  6. WQCXLTrDHxH4D3ii
    WQCXLTrDHxH4D3ii
    rAaom1yKE2bmVq2V

    • Pull out the pin and remove the scroll wheel assembly.

    • Take out the two springs under the scroll wheel assembly.

    • Be careful when lifting the scroll wheel assembly. Do not lose the two specified springs.

  7. pB2YG13XaBjJiPxB

    • Unscrew five 12.5mm screws from the motherboard.

  8. hLrL54U2ONwJ2uHQ
    hLrL54U2ONwJ2uHQ
    BllWBNxasGOWWBXt
    iHNayOYOyUjbayjk

    • Open the tabs lock on each side so you can disconnect the ribbon.

    • Disconnect the PCB from the mouse cable.

  9. X3fbtapjHDpjjkHA
    X3fbtapjHDpjjkHA
    F1JHnSFhZUx6XNRe
    OgcecPspAsFVKvk4

    • Pull out the plastic piece.

    • Remove the mouse cable.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Sen

Member since: 19/09/21

331 Reputation

2 comments

Let's say you're trying to fix your G502 without a legit logitech cord, you can just splice a usb cable and solder the correct wires to the pins. I did this twice and it works flawlessly

Black.Technician -

If you are careful enough, you don't need to remove the side button ribbon.

Yueh Tse Chen -