Karcher Rotary Floor Cleaner 17833080 2017 Vacuum Motor Replacement

Written By: Arthur Shi
  • Comments: 2
Karcher Rotary Floor Cleaner 17833080 2017 Vacuum Motor Replacement

Difficulty

Moderate

Steps

15

Time Required

No estimate

Introduction

This guide shows how to remove and replace the vacuum motor/turbine for the Karcher Rotary Floor Cleaner 17833080 2017.

  1. cvdMERNHLdUGDK3b
    cvdMERNHLdUGDK3b
    StNjh5BI2IvnEQgF

    • Before you begin, make sure to power off and unplug the device.

    • Lift the tank by the handle and remove it from the device.

  2. jBy4DhMReckHQHZh
    jBy4DhMReckHQHZh
    Hnij1DGCDlHW4sWX
    2LQL2UnDUNjrlHnq

    • Press the yellow button near each wheel base to release the wheels.

    • Remove both wheels from their sockets.

  3. IYb1ZxJGGNdsuakj

    • Use a T20 driver to remove the three screws securing the pump cover.

  4. NZ5EyFkomPZKLavV
    NZ5EyFkomPZKLavV
    OdPYSm3UEYqN5aHp
    fivHaIJQuYuAlWa5

    • Remove the pump cover.

  5. Lh2dOXITBv3cLbZj
    Lh2dOXITBv3cLbZj
    AliCXjXZuJCxpuOZ

    • Squeeze the left plug by the edges and pull it out of its socket.

    • During reassembly, make sure that all plugs are firmly seated in their sockets.

  6. f2WGVZPrwjWKAhOJ

    • Use a T20 driver to remove the two screws securing the vacuum cover.

  7. vUuD4OQRQO2PwHoB

    • Remove the vacuum cover.

  8. 2VIx11RJI5JkwU11
    2VIx11RJI5JkwU11
    AXg2JwaucOoUaGBl

    • Pull the clear hose off the vacuum cover.

  9. egID6ox2YE32VeNt

    • Reassembly tip: Use this photo as a reference on how to route the motor wires in the vacuum housing.

  10. xvYQurU1HWCWPTf3
    xvYQurU1HWCWPTf3
    rFDfZYsfWSNj41Rv
    UwYYRrVlgKu3VdMO

    • Disconnect the two motor wires by pulling the plugs off their spade sockets.

  11. VfgjmOAFbmMI6y6a

    • Use a T20 driver to remove the five screws securing the vacuum housing.

    Remove five screws not four.

    STEVE -

    Thanks for the comment! I think I corrected it. If I didn’t, please leave a message.

    Arthur Shi -

  12. XKRavOELNl5qHkhA
    XKRavOELNl5qHkhA
    nUHgRd1oeQD3rwZn
    KICk6w54ZTX43Ts5

    • Lift the vacuum housing to remove it.

    • Reassembly tip: During reassembly, be sure to thread the motor wires through cutout on the side of the vacuum housing.

    • Reassembly tip: Be sure to properly align the vacuum housing to the rubber motor seal.

  13. H1EljxPBsBvjoSLr

    • Lift the vacuum motor from the device to remove it.

  14. OBtBaZAvYrsklfA5

    • Peel the lower rubber seal from the motor and transfer it to the replacement part.

  15. DdKZkkVEISXB4aCF
    DdKZkkVEISXB4aCF
    SCktNhWUfL1ENKSP

    • Peel the upper rubber seal from the motor and transfer it to the replacement part.

    • The upper seal is keyed to the motor. Be sure to properly align it during assembly.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Arthur Shi

Member since: 03/01/18

248651 Reputation

0 comments