How to Patch a Hole in Damaged Carpet

Written By: Kaleigh Smith
  • Comments: 2
How to Patch a Hole in Damaged Carpet

Difficulty

Easy

Steps

9

Time Required

20 minutes

Introduction

If your carpet has an unseemly stain, hole, or burn, use this guide to replace the section without the unnecessary fuss and expense of replacing the entire carpet.

Before beginning the fix, make sure the carpet and the sample piece are clean. Some homes have extra matching carpet leftover; however, carpet can always be purchased at a home improvement store.

  1. vQbeClVHMo3fvDHk
    vQbeClVHMo3fvDHk
    1Ohgk4Ugf46WMHDO
    XSfBS3Gf4dnQu4Gy

    • Place a can over the hole.

    • The can should completely cover the hole.

  2. LtHCIikL2oBxJ5cV
    LtHCIikL2oBxJ5cV
    5JVPUbAH1hXy2l4w
    hy5W1mo2IPUUYIgh

    • Press down firmly on the can.

    • Cut around the can with a utility knife.

    • Utility knives are sharp, so handle with care.

    • Only cut through the carpet. Do not cut through the carpet pad underneath.

  3. ErX5Altv2TJ2AYqE
    ErX5Altv2TJ2AYqE
    L1sovWRZTgOlN2rk
    XO6LV2R6fNlUWBlc

    • Remove the can.

    • Lift out the old carpet.

  4. NYFoVoqL3V3cYtv4
    NYFoVoqL3V3cYtv4
    2piFTVNhWkXpVMWC
    DrTKBlHFRYSktvJg

    • Flip sample carpet onto its back and place down on a stable surface.

    • Place the can onto the sample carpet.

    • Trace the shape of the can with a marker.

  5. LrYMlDTBT1mShCgO
    LrYMlDTBT1mShCgO
    YNQoVpRfpodkTrwJ
    Q6tWqDMhZ1KpMcUS

    • Remove the can from the sample carpet.

    • Cut out the shape from the sample carpet using scissors.

    • Kitchen scissors are sharp. Always cut away from yourself.

  6. cyRpR6TUIpeQPMCm
    cyRpR6TUIpeQPMCm
    yBaVbwO4GFHYx6Zl
    Cp6lpBg4k4mGvyLx

    • Check to make sure the replacement piece of carpet fits into the hole.

    • If necessary, trim sample to fit or cut another piece.

  7. 3yNjoKJ1auebhE2i
    3yNjoKJ1auebhE2i
    VtGcdiuLN4YXpPll

    • Evenly spread glue on the underside of the replacement carpet.

    • The carpet should be placed down before the glue dries.

  8. yObUVPae6gnsyjQk
    yObUVPae6gnsyjQk
    OHHJ2gOVoUIB1uHC

    • Place the glue side of the carpet down into the hole.

    • Press down firmly on the carpet with your hand.

    • Let glue dry before using the carpet.

  9. GkSjMdJVqrlXQVNF
    GkSjMdJVqrlXQVNF
    hZpBk3QNotkmxPRS

    • Trim carpet fibers to blend the replacement carpet with the original.

Conclusion

Once the glue has dried the carpet can be walked on or vacuumed. By cutting the longer carpet fibers the replacement patch should seamlessly blend in with the original carpet.

Author

Kaleigh Smith

Member since: 16/01/20

250 Reputation

2 comments

Very good. I suppose if you don't have same carpet you can match as close as possible with a new piece.

Brian Taylor -

Excellent tip - thank you for sharing!!

Rama Narsing -