How to Clean a YardWork LH3185A Snow Blower Carburetor

Written By: Demitri Roopnarine
  • Comments: 0
How to Clean a YardWork LH3185A Snow Blower Carburetor

Difficulty

Moderate

Steps

11

Time Required

30 - 40 minutes

Introduction

Cleaning a snowblower’s carburetor helps to maintain its performance and prevent issues such as starting problems, fuel-related issues, and poor performance due to the buildup of debris and impurities in the fuel. Utilize this step-by-step guide as a resource to effectively maintain the carburetor for peak performance.

Make: YardWork
Model: LH3185A

  1. I1k4GlOYRpXWAEw4
    I1k4GlOYRpXWAEw4
    3ASG5jM1XLbHBsMR
    noDHw2vPv4IvlRJX

    • Block the gas from coming out of the fuel tank using a locking plier.

    • Alternatively, some snowblowers come with a shut-off valve to lock off the gas line.

  2. 1qfQJrhYrkoGYBB1
    1qfQJrhYrkoGYBB1
    FtZLCjfTauVGPYVh

    • Remove the stop key by pulling outwards.

  3. o1GHnEND1OOYiBcB

    • Remove the choke key using a flat screwdriver.

  4. ZE4SnZueRoJxay4X
    ZE4SnZueRoJxay4X
    DpMAKCyIwPWMBhGV

    • Remove the two support bolts from the outer shield using an 8 mm socket.

  5. nT6NuvYdyHTTJh5c

    • Remove another two support bolts from the outer shield using a Phillips head screwdriver.

  6. ZdWlnFVpGWNd1jQM

    • Loosen the handlebar by turning the knob counterclockwise until there's enough room to safely remove the shield.

  7. tDheNNgto1KsYUHp
    tDheNNgto1KsYUHp
    E2aZgWrThtwXTXGU

    • Remove the inner switch using the 8mm socket.

  8. TtxlWZSiLv1ELleZ
    TtxlWZSiLv1ELleZ
    qjcLrZ2ZXBjHfRja
    QyLcoHWBu4w6wnNc

    • Remove the bolt that holds the reservoir in place using a 13mm socket or spanner.

    • Gas can leak when removing the jet, so have a bucket or towel in place.

  9. qFOyLyJjIOZ4AVnP

    • Remove the reservoir by pulling downwards.

  10. xV1AlEjk5osULlgU
    xV1AlEjk5osULlgU
    RIIiSc5CQLCyVCbR

    • Clean the jet nozzle (all three holes) using a pin or small wire.

  11. T3X2q2V4ZaEyCZS6
    T3X2q2V4ZaEyCZS6
    jaHyAaEtiDVTGBEg
    HP2yKFrQ4IGLwFur

    • Clean the inside of the reservoir, the rubber, and the jet using the carburetor cleaner.

    • When reassembling the reservoir, it is crucial to carefully position the rubber component. Improper alignment of the rubber, combined with excessive tightening of the bolt, can result in damaging the rubber seal.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Demitri Roopnarine

Member since: 28/05/23

293 Reputation

0 comments