HTC One X LCD Display & Touch Screen Glass Digitizer Replacement

Written By: ZFix
  • Comments: 4
HTC One X LCD Display & Touch Screen Glass Digitizer Replacement

Difficulty

Very difficult

Steps

8

Time Required

35 - 40 minutes

Introduction

HTC One X is also known as S720E.

How to disassemble the phone and change the LCD Display & Touchscreen / Digitizer (the complete spare part).


Please SUBSCRIBE to my channel ツ

  1. 1ulvFrTUAJMBkGkc
    1ulvFrTUAJMBkGkc
    HJERLOqUein5u1Uo
    FRYLeohaCu5K1mZi

    • Switch-off the phone (if you can).

    • Remove the SIM tray.

    • The back cover is sticked to the phone with adhesive tape. Is good to use some hot air to do removing of the back cover easier.

  2. GH6fSyWQGNGVtSLJ
    GH6fSyWQGNGVtSLJ
    JovqSZlIhJQyR5SR
    GmsCTiPqXCpwA1Vy

    • Start opening from the bottom side.

    • For separating the back cover, use only plastic tools.

    Be careful around the bottom corners and edges, that you don't put your guitar pick in to deep and break a pin off the logic board.

    Josh Ginsberg -

    There are 3 types of screens! Sony, Sharp and AUO (or something). Look at the color of the flexwire before you order or install. I made the mistake and burned the backlight coil.

    35i -

    hi. which flexwire to whach?

    dkdanniell -

  3. rZZWAsfDyvGYXucp
    rZZWAsfDyvGYXucp
    csZbRQpK3brBvNmi
    VOxsPaM3sIAwaOrO

    • The mother board is held by 6x Philips screws.

  4. KGlIZck4CocduieI
    KGlIZck4CocduieI
    BX1JKPF64gHXaqNW
    en2DqqYibRmNnft1

    • Disconnect one by one:

    • the Touchscreen flex cable

    • the Volume buttons & Mic flex cable

    • the Dock connector flex cable

    • Use a plastic tool to unstick the battery.

    • Be careful, there are flex cables under the battery. At the last picture in this step you can see the cables and the place were is adhesive tape.

    • Now you can separate the Dock flex cable.

  5. DJT4xClPZbXdoHuD
    DJT4xClPZbXdoHuD
    fw4nP65ZK5mctPgF
    xTxapNsnMi6wQUKv

    • Lift the motherboard slightly to disconnect two flex cables:

    • the LCD Display flex cable

    • the Navigation buttons flex cable

    • Disconnect the Power On button flex cable at the upper side of the phone

    • Now the mainboard and the battery are free.

    • Disconnect the battery from the mainboard.

  6. QTHGjtZ5YpTOZgyB
    QTHGjtZ5YpTOZgyB
    cLqFRdfUdGNoMSSf
    fElaYKCDxw6Sh1Hw

    • At the beginning you can use a cutter to make a room for the plastic tool.

    • During the procedure of the separating the LCD Display & Touchscreen from the frame, you can use again hot air. This will make separating more easy.

  7. vwcR6BW6S1RPAxk3
    vwcR6BW6S1RPAxk3
    TqcrRn3s2qxxv5xn
    RXJZwmwNIymoRCpB

    • The original adhesive tape is left on the frame, but I prefer to put new. I put it onto the original.

    • Gently assemble the screen to the frame.

  8. IQUInXWnyHIJZCEA
Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

ZFix

Member since: 09/12/13

191079 Reputation

One comment

i need touch panel do you have available

osama siddique -