HP Photosmart c3180 Control Panel Circuitry Replacement

Written By: Jim
  • Comments: 2
HP Photosmart c3180 Control Panel Circuitry Replacement

Difficulty

Moderate

Steps

11

Time Required

5 - 10 minutes

Introduction

  1. OKnwwk4wKnmRT1TC
    OKnwwk4wKnmRT1TC
    4mMrqMtB2SbxGwDb

    • Before disassembling your printer, be sure that the printer has been unplugged to avoid any risk of injury.

    • Rotate the printer 90 degrees counter clockwise so that the side panel next to control panel is facing you.

    • Remove the two T10 12mm Torx screws from the left side panel.

  2. 6tGoCT5KMFM5Tujb
    6tGoCT5KMFM5Tujb
    sol1ObLCA3Fi5bCP

    • Firmly pull the the back of the side panel until it separates from the body of the printer.

    • Rotate the side panel upwards while pulling it towards yourself to remove the panel.

  3. CJLV3tKkxatgK3C6
    CJLV3tKkxatgK3C6
    VUrdBBDEuq3CDUmO

    • Rotate the printer 90 degrees clockwise.

    • Grasp the paper tray and rotate it down.

    • Insert your fingers into the slot in the printer door and pull to rotate the gate down.

  4. MQNKnT1dnoAeoGPb
    MQNKnT1dnoAeoGPb
    oeKScQC6qWbRxPgM

    • Rotate the printer 90 degrees clockwise.

    • Remove the two T10 12 mm Torx screws.

    • Grasp both sides of the side panel and pull it forward to remove the panel.

  5. lwpt6KWNfsIpZUtp
    lwpt6KWNfsIpZUtp
    ZfvKNRS54AeP1RaT

    • Rotate the printer 90 degrees counter clockwise.

    • Lift the scanner lid to expose the scanner glass.

  6. UATXBmLKNIQvWHWj

    • Remove the two T10 12 mm Torx screws.

    • Do not attempt to lift the top panel off the printer yet because it is still connected to the printer body by a cable.

  7. MCf1iKQovxZeKoOs
    MCf1iKQovxZeKoOs
    tRdaT6fmasSfwWJE

    • Rotate the printer 90 degrees counter clockwise.

    • Inside the printer is a small white tab. Press it inward with a spudger until a pop is heard.

    • Remove the front panel by grasping its front and pulling away from the printer.

    Änderung des Textes: die kleine Lasche verriegelt die kleine Frontblende: mit leichtem Druck Richtung “rechte Druckerseite entriegeln, gleichzeitig jene Blende nach vorn lösen.

    Garofalo -

  8. b4wmJyCQ4dGIfRQm
    b4wmJyCQ4dGIfRQm
    noxLPZnY6FFCoqRa

    • Rotate the printer 90 degrees clockwise.

    • Remove the cable connecting the top panel of the printer to the power button assembly.

  9. I5PMnusHEehpT52Y

    • Carefully lift the top panel of the printer away from the printer body.

    nur die dünne weiße Abdeckung, die graue bleibt noch; zuerst hinten anheben, vorn ist mittig eine Nase zu lösen.

    Garofalo -

  10. jkjXnGxBSLIUB1LH

    • Set aside the printer body.

    • Remove the three T10 12 mm Torx screws from the back of control panel circuit board.

  11. xSWvjZYZMHdlli5B

    • Using both hands, carefully lift the control panel circuit board from the top panel of the printer.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Jim

Member since: 06/10/11

1590 Reputation

0 comments