Introduction

Use this guide to replace the motherboard of your HP 14-dq0051dx laptop. The motherboard is the central part to a laptop that enables it to function as a whole. Many components are connected to the motherboard which allows data to travel within those parts.

Before beginning this replacement, turn your laptop off and unplug from the AC adapter.

  1. qE1MK6D4tX2pgIIB
    qE1MK6D4tX2pgIIB
    FXLaYCV1nwvNGLsY
    • Turn the laptop upside down so the backside is facing up.

    • Remove the eight 2.5mm screws from the back case using the Phillips #1 screwdriver.

  2. RbFQ3EYagZKLEL1P
    • Turn the laptop over and open the screen.

    • Insert the blue opening tool into the seam between the keyboard and bottom panel.

    • Run the blue opening tool along the entire seam in order to separate the bottom panel.

    • You may hear clicking as you release the taps that secure the case.

  3. Q6EJxUKMBmCGucAE
    • Once the bottom panel is separated from the laptop, carefully close the laptop.

    • Turn the laptop upside down again so the backside is facing up.

    • Place both hands on opposite corners of the bottom panel and carefully lift it up to remove the panel.

  4. SRLq5GxSQHtcBOHa
    SRLq5GxSQHtcBOHa
    bXKwOqXSLFTMLhxi
    OTedJZEesswBx5KR
    • Remove the five 2.5 mm screws that secure the motherboard cover using a Phillips #1 screwdriver.

    • Using your hands, remove the motherboard cover from the laptop.

  5. JwaVVHAuw3eDuxXU
    JwaVVHAuw3eDuxXU
    RFTofEivtEDtiMMC
    21qucOnDDHTpAoQU
    • Use a Phillips #1 screwdriver to remove the four 2.5 mm screws that secure the battery.

    • Remove the battery from the laptop.

  6. sRd2HSplD3aLtVUj
    sRd2HSplD3aLtVUj
    YUalcUbOBBxprqG1
    QKKsP4PbcF4Rii1X
    • Use the blue opening tool to flip up the small locking flap from the ZIF connector that attaches the touchpad cable to the motherboard.

    • Gently pull the ribbon cable out from the connector.

  7. lvB2GNlexyJFGCE6
    lvB2GNlexyJFGCE6
    IhpiluDSRmD4QPRy
    • Gently unplug the keyboard connector from the motherboard.

  8. LHJDFn46HovhVScE
    LHJDFn46HovhVScE
    eYrlJQyhOdGP6QQU
    • Lift up the small compartment with your finger.

    • Pull the flat cable out of the connector.

  9. SSEIfOHFgWtvqxVy
    • Unplug the battery connector from the motherboard using both fingers.

  10. tnRqmdArCxCdUZvt
    tnRqmdArCxCdUZvt
    UwFGQCpeVAMl6fGm
    62AVqeDHygVeUhAi
    • Lift the black square card covering two small cables connected to the WIFI card.

    • Unplug the small wires one and two with your fingers.

    • Use a Phillips #0 screwdriver to unscrew the single 1mm screw that secures the WIFI card.

    • Remove the WIFI card by gently pulling it out of its slot.

  11. 4iMpQuoAh1ScscUn
    4iMpQuoAh1ScscUn
    iq1YgeYDMEhQFSaL
    • Pull the charging port cable away from the connector in the same direction as the individual wires to unplug the charge port connector.

    • Remove the charging port.

  12. 2SqxDrIkjkhGFTJc
    2SqxDrIkjkhGFTJc
    bTVCQs11HCxmMlYJ
    • Lift up the port using the blue opening tool.

    • Continue to lift up until it is unplugged from the motherboard.

  13. XX1hLpKoUZTcJPdx
    XX1hLpKoUZTcJPdx
    kNVUDZFLINRN1HAC
    • Place both hands on opposite corners of the motherboard and carefully lift it up to remove it from the laptop.

    • Now the motherboard has been successfully removed and is ready to be replaced!

Conclusion

To reassemble your device, follow these instructions in reverse order.

Akash

Member since: 09/11/23

601 Reputation

0 comments