Garmin Vívoactive 4 Battery Replacement

Written By: Bryan Chavez

Comments: 4

Difficulty

Moderate

Steps

Time Required

45 minutes - 1 hour

Introduction

Replacing the battery of the Garmin Vívoactive 4 (M/N: 03618) is not simple, although it does not require any soldering.

You may want to replace your battery if you suspect that it is going bad or otherwise not functioning properly. Before going ahead with this, we suggest you take a look at the Device Battery Drains Fast section in our Vívoactive 4 Troubleshooting Guide.

If you notice that your battery is swollen, take precautions to avoid injury. This article, What to do with a swollen battery offers helpful information on what to do. Make sure to recycle the battery or dispose of it properly.

This guide requires the use of a heat gun and iOpener. See these articles, How to Use a Heat Gun to Soften Adhesive and iOpener Instructions for instructions and safety information.

Tools

Parts

Garmin Vivoactive 4 Watch Main Board PCB

Step 1

Flip the watch on its back to reveal the watch band connection pins.

Step 2

Wedge your fingernail or the tip of a spudger underneath the watch band's small metal pin.
Push on the pin to release the strap from it's hinge.
Pull the strap away from the watch to disconnect it.
The strap will not pull away if the pin isn't fully pushed in.

Step 3

With both straps removed, a new replacement watch band may be inserted.

Step 4

Use a heatgun to loosen the adhesive beneath the screen, it should take a 5-10 minutes for adhesive to loosen.
Handle the watch with care to avoid burning yourself after it has been heated. Review the How to Use a Heat Gun to Soften Adhesive guide.

5-10 minutes is too long and too short at the same time. I didn't even heat it for 5 minutes on low and the watch was already too hot to touch. I put on some gloves and tried to wedge my jimmy in between the screen and the case but the seam is much too thin, even when I broke out my knife for it. I thought the glue must not be loose enough yet, so I heated it for a couple more minutes and tried again. Even though I did completely discharge my battery before doing any of this, my battery started to bulge and the back of my watch deformed. I followed these instructions as closely as possible, along with the "how to use a heat gun to soften adhesive" guide, and I never got my screen off and now my watch is beyond reasonable repair. If you decide to try this, I hope you have better luck, but I don't know how you're supposed to be able to get this done.

cram C -

Step 5

Wedge a thin opening tool or your iFixit Jimmy in between the seam where the screen and the watch’s housing connect.
Pry the screen off the device.
There is a cable underneath the screen that needs to be disconnected - be careful not to rip it.
Work quickly so the adhesive doesn’t cool too much.

Step 6

Carefully disconnect both cables from the motherboard by placing the tip of your spudger under the edge of the connector, and prying the connector straight up from its socket.

Step 7

Remove the screen.

Step 8

Carefully peel off the ribbon tape that is holding down the motherboard.

Step 9

Place the tip of your spudger under the edge of the connector, and pry the connector straight up from its socket to disconnect the battery from the motherboard.
Do this carefully to avoid ripping the cable.

Step 10

Use a Phillips #00 screwdriver to remove the 3.2 mm screw on the motherboard.
Use a Phillips #00 screwdriver to remove the 4.8 mm screw on the motherboard.

Step 11

Pull the battery cable up to dislodge the motherboard.
Gently remove the motherboard from the socket.
The motherboard may get caught under the housing due to the clips on the edge.

Step 12

Use the pointed tip of a spudger to carefully push on each side of the battery connector to disconnect the battery from the motherboard.

Step 13

Use a spudger to pry the battery from the case.
Be careful not to damage any surrounding components.
There is an adhesive holding the battery down. Use an iOpener if it is too difficult to remove the battery with the spudger alone.