G-Wolves Hati Paracord Replacement

Written By: Ayaan
  • Comments: 0
G-Wolves Hati Paracord Replacement

Difficulty

Easy

Steps

20

Time Required

15 - 25 minutes

Introduction

This guide is used to replace or swap the cord/paracord on the G-Wolves Hati mouse.

The paracord is the wire which connects the mouse to the computer and allows the mouse to function and guide the cursor. It is a lighter form of cable which is used in gaming mice in order to alleviate the feeling of having a cable attached to a mouse. With a faulty paracord, the mouse sensor could not only be stuttering, but there is a chance the entire mouse will disconnect or not function whatsoever (even if the rest of the components are all in working condition).

Steps 2 and 3 involve removing mouse skates from the feet. Be careful not to create, bend, or fold lines on these feet as they will be felt when moving the mouse. Peel them slowly.

Make sure to have the mouse disconnected before beginning the guide.

  1. fjDuxIHn3mPYSjLt

    • Flip your mouse upside down.

  2. wqvZKrNZKVhsYCvx
    wqvZKrNZKVhsYCvx
    UkCy3Qp3IQ13xQTT
    BmyaqxWKXsudTPDU

    • Peel off the back right mouse skate.

    • Peel slowly, you don't want to create bends on your skate.

  3. NTUTjTXMqfGBlgRI
    NTUTjTXMqfGBlgRI
    GMVKyZBrunMXZVFp
    Qw23vA4UHwKRFVaD

    • Peel off the back left mouse skate.

    • Peel slowly, you don't want to create bends on your skate.

  4. YgNFS4yPHLHWrAqC
    YgNFS4yPHLHWrAqC
    uLDja4PAHkIZVPwa
    wUyxorLkWfgxvsPg

    • Unscrew both of the uncovered screws.

    • 6.4mm Phillips-head screws.

  5. Fl6UOpYQinhms4Zn
    Fl6UOpYQinhms4Zn
    jCIDvlIFt2xM3A1F

    • Squeeze the mouse under second mouse button until the bottom opens.

  6. HaIQfqiGXfXISOHK
    HaIQfqiGXfXISOHK
    MjjJdxtTfDHoMSQg

    • Pull the bottom piece towards the back of the mouse and upwards to remove it.

    • Pull carefully there is a ribbon cable still connected.

  7. xMCtCM6WQQiAYHvn
    xMCtCM6WQQiAYHvn
    OI2igmb1CoBVkrpx

    • Remove the ribbon cable connecting the bottom piece to the upper piece.

  8. qTcKbkwaSUfO6VE5
    qTcKbkwaSUfO6VE5
    GHMBEYNEGUtFTaIM

    • Unscrew the following screws:

    • 4.8 mm Phillips-head screws.

  9. XwIUXt5Jw1YuM4NU
    XwIUXt5Jw1YuM4NU
    5sJXGuc41xtoSbhD

    • Flip the bottom piece upside down.

    • Pull the circuit board off without pulling on the cable.

  10. kJpVRNDgCsXJoAS1
    kJpVRNDgCsXJoAS1
    WcaWfXuTQIUA2N6M
    Q5RNW5PqWYH6SRYE

    • Grab the side ridges and remove the connection.

    • Do not wiggle till slightly removed to not bend pins.

  11. PBe5ouBlgbvXIkCN
    PBe5ouBlgbvXIkCN
    bdlodCRZvxHRDrCp

    • Pop off the paracord from the bottom piece.

  12. X2DKZ5wwBYUYji4R
    X2DKZ5wwBYUYji4R
    ivprI5F1GUmW6LxV

    • Press in the new paracord.

  13. PW6QtI5LhZdWLjUP
    PW6QtI5LhZdWLjUP
    iRRwVhH3xUnyrNeD
    fqaoEVmZS63PNcyO

    • Rearrange wires to follow the guide ridges.

  14. 2CqhAK4oP4yPrOtu
    2CqhAK4oP4yPrOtu
    4AKpxRAIZe4R6An2

    • Re-insert the circuit board by lining up the scroll wheel with the front piece and pressing down.

  15. hU5KkCq5IgrdJFyq
    hU5KkCq5IgrdJFyq
    CArqtECGuFm3RFYh

    • Re-insert the screws.

    • 4.8 mm Phillips-head screws.

  16. wWxSvVPM1cAg2Gej
    wWxSvVPM1cAg2Gej
    6LyaJNpHvuRtcIVj

    • Thread the wire through the side opening.

    • Insert the paracord connection.

  17. 1CJLKJDiPaYInFbg
    1CJLKJDiPaYInFbg
    UQIYvcXFFGTFLeCf

    • Insert the ribbon cable.

    • Cable is located on the upper mouse piece.

  18. tc2gcNmbUTMnGyug
    tc2gcNmbUTMnGyug
    gk2Q3IQxmuEGFZya
    cQAF6SujXwDUbUkh

    • Hover the bottom piece over the upper piece flipped over.

    • Press the bottom piece down and forward till under clip pieces.

    • Press down where skates where removed till there is a click.

  19. AFjlsjUhxfU1DYl6
    AFjlsjUhxfU1DYl6
    FCBtrSqqHtyXG26X

    • Insert the screws.

    • 6.4mm Phillips Head Screws.

  20. hQMBQMXZWQHUGBu1
    hQMBQMXZWQHUGBu1
    FhVNReHfGREmTuLq
    wMZHL5TC2hvK4Pls

    • Press on the skates.

Author

Ayaan

Member since: 23/10/23

301 Reputation

0 comments