Introduction

Learn how to replace the filter of your Enagic Water filter SD501 Platinum to maintain its function with this filter replacement guide.

It is important to do this replacement since we would want to keep your water source as clean as possible. The filter should be always replace in 6-9 months. You can always make sure by marking the dates down.

Make sure you have prepared a brand new filter for steps 7 and 8 to replace the old one.

Before beginning, you might want to clean up the surroundings. You don’t want anything getting in your water filter machine.

  1. naufN4lWfHbOVlJc
    • Turn off and unplug the machine before cleaning it.

    • Clean the machine with a damp cloth or paper towel.

    • Make sure nothing dirty will get in the machine during the process.

  2. GGOYEogMXMg4RM1H
    GGOYEogMXMg4RM1H
    tQUmEQ1P3mqNZYLJ
    jmSt3k6qTf4HGTWC
    • Open the filter door by pushing the "Push" button.

  3. mbc36L5dxVfXgFfG
    mbc36L5dxVfXgFfG
    JTCFmibcG3uThAie
    nvJJUVKOhTljuZjl
    • Turn the ring at the bottom of the filter to the left until you hear a "click".

  4. 2gaHNSrfWciZu4eY
    2gaHNSrfWciZu4eY
    TOH3li4aqXFLxTmu
    • Remove the ring for now.

  5. TsdLFLAkCCgtwpAI
    TsdLFLAkCCgtwpAI
    A4YXVSBiyGqT55vq
    • Lift up the old filter and discard or recycle appropriately.

    • Some water might be dripping out from the bottom of it. Have a towel ready to clean it up.

  6. cEksFXLm4lUvxNRM
    cEksFXLm4lUvxNRM
    egRgdWo3ANiT1UF1
    YWWWsRXVvljTgiBI
    • Remove the two black rubber rings.

    • They are NOT components of the machine. The new filter you have prepared should come with new ones.

  7. qGVGNnsDM52lNy1F
    qGVGNnsDM52lNy1F
    RWNpvGMhepI1Ykmn
    O5IQcpPoVvVoYGiM
    • Put your new filter in it.

    • Make sure that the two holes match the two popped-out parts from the filter.

    • The one that is bigger should be on the middle and the smaller one should be on the side.

    • This filter should be the new one that you have prepared and NOT the one that is removed from Step 5.

  8. MdBZJo6D4WPQNiK1
    MdBZJo6D4WPQNiK1
    tfpXTtDeR1Hu26MU
    OQF4oscjHSmmAs3q
    • Put the ring component back in.

    • Turn it to your right until you hear a click.

    • Make sure it is successfully locked in.

  9. XCkBG3lBR5iRye2u
    XCkBG3lBR5iRye2u
    DLekuSLt4M5wVXxi
    xRrXalHaWJ3wWx1p
    • Turn the filter back on.

    • Press the "Reset Switch"

    • "FILTER RESET" should be shown on the display.

  10. 6yqQDWMxkPPIhPWL
    6yqQDWMxkPPIhPWL
    Fxda5cJXBRP3DEjG
    425RqmbLgQTAnuKo
    • Attach the filter door.

    • There are three holes to slide the door edge into.

    • And push the "push" button to close it.

Conclusion

To change another filter, simply just follow the instructions once more.

Edwin Ng

Member since: 13/09/21

181 Reputation

0 comments