Apple Watch SE Screen Replacement

Written By: Dominik Schnabelrauch
  • Comments: 6
Apple Watch SE Screen Replacement

Difficulty

Moderate

Steps

19

Time Required

1 - 2 hours

Introduction

Use this guide to replace a broken, cracked, or defective display on your Apple Watch SE.

Replacing the display can cause issues with Apple Pay. If possible, to reduce the likelihood of problems, delete all your Apple Pay account info before the replacement, and then re-enter it with the new display installed.

You’ll need replacement adhesive to reattach components when reassembling the device.

  1. mo33KfMq6MFg3cTl
    mo33KfMq6MFg3cTl
    3hHPP6iIqOmNJMih

  2. Y64ELMHTmEDpMRTL
    Y64ELMHTmEDpMRTL
    44l5RQKvKgBSGeAb
    Qe1UlpsaJFPNFsNq

    • Because the gap between the screen and watch body is so thin, a sharp blade is needed to separate the two. Read the following warnings carefully before proceeding.

    • Protect your fingers by keeping them completely clear of the knife. If in doubt, protect your free hand with a heavy glove, such as a leather shop glove or gardening glove.

    • Be careful not to apply too much pressure, as this might cause the knife to slip and cut you, or damage the watch.

    • Wear eye protection. The knife or glass may break, sending pieces flying.

    • Attach or remove the watch band as needed to provide more control as you make repairs.

  3. 2uIcbKOlKLYdYmYo

    • Prepare an iOpener (or use a hair dryer or heat gun) and heat the face of the watch to loosen the display adhesive.

    • Leave the iOpener on the watch for at least two minutes to fully heat the screen and soften the adhesive holding it to the case.

    • You may need to reheat the iOpener and repeat this procedure several times until the display adhesive softens.

  4. rdKLuZuLUr56gONk
    rdKLuZuLUr56gONk
    mRo164BHGmqrUByF
    UW4fWyQUt1G3OnXp

    • Place the edge of a curved blade into the thin gap between the display and the outer case. Start at the short side of the display, closest to the digital crown.

    • Press firmly straight down into the gap.

    • Once inserted, tilt the blade to pry the display open slightly.

  5. ApqFhhVhjoSiIR2d
    ApqFhhVhjoSiIR2d
    CyPqkoeRDVO1R6fM
    mVeXqLuXQSXKpX4H

    • Insert an opening pick in the gap you've created.

    • Slide the opening pick along the short edge of the watch to cut the adhesive.

  6. OfhNyvPrUr6qRjr1
    OfhNyvPrUr6qRjr1
    VoKpKPMocUe3Yjoe

    • When slicing near the crown, don't insert the opening pick deeper than 1/16th of an inch (~2 mm).

    • Slide the opening pick around the corner and along the long edge where the crown is located to cut the display adhesive.

  7. JWPL6WGJgRkmrDpa
    JWPL6WGJgRkmrDpa
    tAZPGUDRWYqQmibA

    • Slide the opening pick around the corner to cut the remaining adhesive on the short edge farthest away from the crown.

  8. cPmjlmFRcOvTVKtx
    cPmjlmFRcOvTVKtx
    UGQTuHkZhFSZDIfM

    • Place the watch on a flat surface and use an opening pick to slice through any remaining adhesive.

    • When slicing near the crown, don't insert the opening pick deeper than 1/16th of an inch (~2 mm).

    • Slide an opening pick under the opposite display edge of the watch crown.

  9. muJHDTyHhPi3f1Jf
    muJHDTyHhPi3f1Jf
    ifHvtCaDjbAeUwaS

    • Reinsert the opening pick on the short edge of the watch, next to the watch crown.

    • Twist the opening pick to loosen the display off the watch case.

    • Don't try to remove the display. It is still connected to the watch assembly.

  10. 5ySdc6aIDDqSx6u4
    5ySdc6aIDDqSx6u4
    vbHHFmcB4t1Nn6Yh
    KQxILsMjIYmr1ZVK

    • Be careful not to strain the display cables when you fold the display to the side.

    • Lift the display and carefully pull it in direction of the short edge farthest away from the crown.

    • Swing the display open to an upward position.

  11. UCJx6GedKlgjNsAX
    UCJx6GedKlgjNsAX
    BwTHy5wojSMa6O4G

    • The black foil which covers the display connectors is very fragile and likely to rip. To keep the tape intact while peeling it off, it's necessary to use high isopropyl alcohol or an iOpener.

    • Prepare an iOpener (or use a hair dryer or heat gun) and heat the face of the watch to loosen the adhesive tape.

    • You may need to reheat the iOpener and repeat this procedure several times until adhesive softens.

    • Alternatively, apply a little bit of high-concentration isopropyl alcohol (>90%) to a Q-tip and apply it to the black adhesive foil on top of the display connectors. Let it penetrate the adhesive for about two minutes.

  12. jAXfNNFfQo52fMxS
    jAXfNNFfQo52fMxS
    rAOLLgMXrydifcL6

    • Use a pair of tweezers to carefully peel off the tape covering the right display cable connector.

  13. YXOJADeJehcmNqCt
    YXOJADeJehcmNqCt
    OJOdTZuce3BlD1a5

    • Use a pair of tweezers to carefully peel off the tape covering the middle and left display cable connector.

  14. FEFCZQ5l6HCCyHHi
    FEFCZQ5l6HCCyHHi
    FeNPe3I2C5HhqUAs

    • Use the pointed end of a spudger to open the right ZIF connector on the rear side of the display by bringing its flap in an upright position.

  15. N6DSBOoPSldJLTXP
    N6DSBOoPSldJLTXP
    baoCHMfI42jaHmcu

    • Use the pointed end of a spudger to open the middle and left ZIF connectors by bringing their flaps to an upright position.

  16. 2YfIrQXOmyQeobED
    2YfIrQXOmyQeobED
    mi1qmeaO1Y1fJQxC

    • Use a pair of tweezers to peel the left edge off the display cable sticker off the rear side of the display.

    • Do not try to remove the sticker all the way, you will reuse it when reassembling your watch. Only peel the area off which adheres the cable to the rear side of the display.

  17. KyXYqcP55LxETDXZ
    KyXYqcP55LxETDXZ
    JxflmIEveZDjfCea

    • Use a pair of tweezers to peel the right edge off the display cable sticker off the rear side of the display.

  18. JB1U1WaoDhOuGyci
    JB1U1WaoDhOuGyci
    binD1XNYIKZDQJfl
    PrgDamMbSdG2LRGW

    • Carefully pull the display flex cables out of their ZIF connectors.

    • Only pull close to the ZIF connector and not on the watch body. Otherwise the display cable might rip.

  19. pgnGPfC2vIf2WBjW

    • Separate the watch assembly and the display.

    The NFC chip will need to be transferred from your old display to your new one or you need to remove the watch from your iPhone fully and then treat it like a new watch,

    Dan -

Conclusion

To reassemble your Apple Watch SE follow these instructions in reverse order to reattach the screen and the battery.

Apply a little bit of high isopropyl alcohol (>90%) to a Q-tip or use a cleaning pad to gently remove the leftover adhesive on the edges of the watch case and the screen before installing new adhesive.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Author

Dominik Schnabelrauch

Member since: 23/11/16

201132 Reputation

5 comments

any idea where I can purchase the replacement screen itself?

donald maida -

Would have nice to know about the NFC antenna before this. I now have no Apple Pay.

Care O -

Where is the NFC antenna? I wish they showed how the new one will adhere to the body. They have listed to buy a roll of adhesive tape but I don't get it.

David -

Does the pre-cut adhesive card have the necessary cuts to re-attach the crystal ?

RLRams -

Will I be able to preserve the NFC antenna after replacing the screen?

Jake_a_spade -