Wireshark

Wireshark is a free and open-source packet analyzer. It is used for network troubleshooting, analysis, software and communications protocol development, and education.

Installation

Install the wireshark-qt package for the Wireshark GUI or wireshark-cli for just the tshark(1) CLI.

Note: The deprecated GTK interface has been removed in Wireshark 3.0.

termshark is an alternative terminal UI.

Capturing privileges

Do not run Wireshark as root; it is insecure. Wireshark has implemented privilege separation, which means that the Wireshark GUI (or the tshark CLI) can run as a normal user while the dumpcap capture utility runs as root.

The wireshark-cli install script sets packet capturing capabilities on the /usr/bin/dumpcap executable.

/usr/bin/dumpcap can only be executed by root and members of the wireshark group, so to use Wireshark as a normal user, you have to add your user to the wireshark user group.

A few capturing techniques

There are a number of different ways to capture exactly what you are looking for in Wireshark, by applying capture filters or display filters.

Note: To learn the capture filter syntax, see pcap-filter(7). For display filters, see wireshark-filter(4).

Filtering TCP packets

If you want to see all the current TCP packets, type tcp into the Filter bar or in the CLI, enter:

$ tshark -f "tcp"

Filtering UDP packets

If you want to see all the current UDP packets, type udp into the Filter bar or in the CLI, enter:

$ tshark -f "udp"

Filter packets to a specific IP address

  • If you would like to see all the traffic going to a specific address, enter display filter , replacing 1.2.3.4 with the IP address the outgoing traffic is being sent to.
  • If you would like to see all the incoming traffic for a specific address, enter display filter , replacing 1.2.3.4 with the IP address the incoming traffic is being sent to.
  • If you would like to see all the incoming and outgoing traffic for a specific address, enter display filter , replacing 1.2.3.4 with the relevant IP address.

Exclude packets from a specific IP address

ip.addr != 1.2.3.4

Filter packets to LAN

To only see LAN traffic and no internet traffic, run

(ip.src==10.0.0/8 AND ip.dst==10.0.0/8) OR (ip.src==172.16.0.0/12 AND ip.dst==172.16.0.0/12) OR (ip.src==192.168.0.0/16 and ip.dst==192.168.0.0/16)

This will filter traffic within any of the private network spaces.

Filter packets by port

See all traffic on two ports or more:

tcp.port==80||tcp.port==3306
tcp.port==80||tcp.port==3306||tcp.port==443

Headless capturing with dumpcap

dumpcap is part of Wireshark and can be used for capturing packets without the GUI. Used in combination with tmux will allow the capture of packets in a detached session.

To see all dumpcap options, use the flag.

The following example will provide a ringbuffer capture. It captures twenty .pcap files of 100MB each, replacing the oldest file with the twenty-first file and so on… This allows a continuous capture without exhausting disk space.

# dumpcap -i 1 -b filesize:100000 -b files:20 -w mycapture.pcapng
  • − interface number (listed from dumpcap -D)
  • − file size in kB before starting a new .pcap file
  • − the number of files to capture before overwriting the oldest
  • − write the output to the file
gollark: <@185325259673698304> TE lets you manually set input/output slots and sides in the GUI.
gollark: What I usually do is have all my headless EEPROMy devices boot from a code file on the interwebs.
gollark: I would say Thermal stuff.
gollark: It can do some stuff, like redstone IO with a card, or wireless networking also with a card.
gollark: Those are external components.
This article is issued from Archlinux. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.